Safety Precautions - Haier 50FREE-1 User Manual

Safety precautions

Please plug the power plug on special receptacle.
Be sure to use three-pins power receptacle. Ensure
that the earthing prong of the power receptacle is
earthed reliably. Use leakage protector if possible.
Earth
Do not bend ,extend,twist,bind by force.Do not press or nip it with weight.
Keep the pin of the power plug clean,if the power plug is polluted with dust,
please wipe with dry cloth carefully.
If the power cord or the power plug is bad, to avoid risk it is
required to have it replaced by the technicians of our
special shop or our customer care agent.
In case the washing machine is installed on ground with
carpet, do not block the ventilation hole with carpet.
The ventilation
holes at the bottom
Carpet
Do not put the machine at damp place like
the bathroom. Never wash it with water. Do
not put wet laundries on the control panel.
Do not let the machine share one receptacle with other
electric appliances. If the plugging into the receptacle
is loose, do not use the plug any more.
2
The washing machine must be positioned so that
the plug is accessible. Be sure to pull the plug off
and close the water faucet in following cases:
power failure, delivering the machine, setting the
machine idle or cleaning the machine. Do not plug
or pull the power plug with wet hand.
Do not use water hotter than 50 .
Do not wash water-proof laundries like
the raincoat, bike covers etc. to avoid
abnormal vibrations in spinning and
damages to the laundries.
Trouble-shooting answer to question
(If there's breakdown, please pull off the power plug before checking) The following phenomena are not
breakdowns sometimes. Please confirm again before sending it to repair. Do not repair it by yourself.
Phenomena The reason
The digitron displays E0.
The top lid is opened during reserve procedure.
The drainage cannot work, or is too slow.
Is the drain hose blocked?
The digitron displays E1.
After long running of pump in the hot
weather, power will be cut automati-
cally for safe.
It stops running in midway. The digitron
The top lid is not closed.
displays E2.
Are the laundries put slantingly?
The safety switch acts, and the
Is the machine slanting?
spinning cannot work. The
digitron displays E3.
Is the water tap opened, or is there water
The water filling does not work, or is
supply failure?
slow. After a period of time, the digital
Is the water inlet valve blocked?
displays E4.
Is the water pressure too low?
The digitron displays E6.
The water level sensor is bad.
Is there power failure?
Not wash
Is the power plug inserted tightly?
Is the water level reached preset position?
The machine does
not act
Is the power plug inserted tightly?
Not spin
Is the top lid closed reliably?
Are the laundries set flat?
There's abnormal sound Is the machine slanting?
Are the laundries put slantingly in spinning?
inside the machine
Are there any foreign materials?
Is the jointer of water inlet hose loose
The water faucet leaks
or awry?
Common phenomena
Phenomena
Balance the laundries to avoid slanting.
The spinning is intermittent when it starts.
The cloth sensor is checking the cloth, it willadd waterafter 48 seconds.
The wash procedure is paused.
The program is setting the drain time. Some time is needed
Push the SPIN button , but it doesn't work.
before it starts spinning.
The pulsator pauses during water inlet
It is to avoid splashing during water inlet.
in wash and rinse.
There may be some water flowing out of the
It is the water remained in the factory inspection of performance.
drain hose in the first use of the machine.
How to settle
Close the top lid.
Clean the foreign material. Open and close The top Lid Once.
Some minutes later the machine will
continue to work
Close the top lid.
Reorder the laundries.Close the top lid.
Th machine will start running after 10
seconds of being placed horizontally.
Open the water tap. Push the start/Pause
button once.
Clean the water inlet valve then push
the start/Pause button once.
Push the Start/Pause button once.
Please contact the customer care
agent.
Please use it when there's power supply.
Insert the power plug tightly.
Fill water to the preset position.
Insert the power plug tightly.
Close the top lid.
Set the laundries flat.
Adjust the machine to be even
Reorder the laundries and close the top lid.
Remove the foreign materials.
Fasten the jointer properly.
Explanation