Electrical Requirements; Range Installation - Electrolux EW30GS75KSD Installation Instructions Manual

Theconversion mustbeperformed b ya qualified service
technician i n accordance withthe manufacturer's
instructions a ndalllocal c odes andrequirements. Failure
to followtheseinstructions couldresult i n serious injury
or property damage. Thequalified agency performing
thisworkassumes responsibility forthe conversion.
Failure t o make the appropriate
conversion canresult i n serious personal injuryand
property damage.
| Electrical Requirements
120 volt, 60 Hertz, properly grounded dedicated circuit
protected by a 15 amp circuit breaker or time delay fuse.
Note: Not recommended to be installed with a Ground
Fault Interrupt (GFI).
Do not use an extension cord with this range.
Grounding Instructions
IMPORTANT Please read carefully.
For personal safety, this appliance must be properly
grounded.
The power cord of this appliance is equipped with a
3-prong (grounding) plug which mates with a standard
3-prong grounding wall receptacle (see Figure 6) to
minimize the possibility of electric shock hazard from the
appliance.
Preferred Method
Grounding type
wall receptacle
x
Do not, under any
circumstances, cut,
remove, or bypass
the grounding
prong.
Power supply cord with
3-prong grounding plug.
Figure 6
The wall receptacle and circuit should be checked by
a qualified electrician to make sure the receptacle is
properly grounded.
Where a standard 2-prong wall receptacle is installed,
it is the personal responsibility and obligation of the
consumer to have it replaced by a properly grounded
3-prong wall receptacle.
Do not, under any circumstances, cut or remove the
third (ground) prong from the power cord.
Disconnect electrical supply cord from
wall receptacle before servicing cooktop.
Moving the Appliance for
Servicing and Cleaning
Turn off the range line fuse or circuit breakers at the
main power source, and turn off the manual gas shut-off
valve. Make sure the range is cold. Remove the service
drawer (warmer drawer on some models) and open the
oven door. Lift the range at the front and slide it out
of the cut-out opening without creating undue strain
on the flexible gas conduit. Make sure not to pinch
the flexible gas conduit at the back of the range when
replacing the unit into the cut-out opening. Replace
the drawer, dose the door and switch on the electrical
power and gas to the flame size.
Range Installation
Important Note: Door removal is not a requirement for
installation of the range, but is an added convenience.
Refer to the Use and Care Guide for oven door removal
instructions.
Standard Installation
_DI The cooktop overlaps the at the
range
countertop
sides and the range rests on the floor. The cooktop
is 311/2'` (80 cm) wide.
_ Install base cabinets 30" (76.2 cm) Make
apart.
sure they are plumb and level before attaching
cooktop. Shave raised countertop edge to clear
311/2" (80 cm) wide range top rim.
_}1t Install cabinet doors 32" (81.3 cm) min. apart SO 8S
not to interfere with range door opening.
Cutout countertop exactly as shown on page 1.
Make sure the two front leveling legs and the rear
leveling wheels are setup higher than the height of
the cabinet.
_ emove and discard the two rear leveling legs,
they are only in place to solidify the unit for the
transport.
O _ Install the anti-tip bracket
at this point before placing the range at its
final position. Follow the installation instructions
on page 12 or on the anti-tip bracket template
supplied with the range.
_To provide an optimum installation, top
the surface
of the countertop must be level and flat (lie on the
same plane) around the 3 sides that are adjacent
to range cooktop. Proper adjustments to make
the top flat should be made or gaps between the
countertop and the range cooktop may occur.
_11_ To reduce the risk of damaging
your appliance, do not handle or manipulate it by
the cooktop. Manipulate with care.
7