Table of Contents
Advertisement
Available languages
Available languages
Quick Links
_.:::_
!i!i!!!!i
C Oi"i_ :!!!iiiii_
u ii'_ ' '_ _!!!!!!
i¸¸¸¸ i!!!iiiilk
iH_
iqd u _i!!!iiii_i_
t:: i :iO!i i
Appliances
Installation Instructions
Spacemaker®Dishwasher
If you
have questions, call 800.GE.CARES
(800.432.2737)
or visit our website at: www.GEAppliances.com
BEFORE YOU BEGIN
Read these instructions
completelg
and
carefutlg.
IM PORTANT-
Observe all governing
codes
and ordinances.
• Note to Installer-
Be sure to leave these
instructions
for the consumer
and local inspector's
use.
• Note to Consumer - Keep these instructions with
your Owner's Manual for future reference.
• Skill Level-
Installation
of this dishwasher
requires
basic mechanical, electrical and plumbing skills.
Proper
installation
is the responsibility
of
the installer.
Product
failure
due to improper
installation
is not covered
under
the GE
Appliance
Warranty.
See warranty
information.
• Completion
Time - I to 3 Hours.
New
installations
require
more time than
replacement
installations.
• Sink Requirement
- This Spacemaker
® dishwasher
is designed
to be installed
under
a special
shallow
sink. Three types
of sinks are available:
GPF95, a
single
bowl sink with the drain hole on the right
side of the sink; GPF96, a single
bowl sink with the
drain
hole on the left side of the sink; and GPF97, a
double
bowl sink. Purchase
these sinks from gour
authorized
GE appliance
dealer.
IMPORTANT-
The dishwasher
MUST be
installed to allow for future removal from the
enclosure
if service is required.
If you received
a damaged
dishwasher,
you should
immediately
contact
your
dealer
or builder.
Optional Accessories - See the Owner's Manual for
available custom panel kits.
FOR YOUR SAFETY
Read and observe
all CAUTIONS
and WARNINGS
shown
throughout
these
instructions.
While
performing
installations
described
in this booklet,
gloves
and safety
glasses
should
be worn.
J
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
Advertisement
Table of Contents
Related Manuals for GE Spacemaker GSM2200V00WW
Summary of Contents for GE Spacemaker GSM2200V00WW
- Page 1 C Oi"i_ :!!!iiiii_ u ii'_ ' '_ _!!!!!! i¸¸¸¸ i!!!iiiilk iqd u _i!!!iiii_i_ t:: i :iO!i i Appliances Installation Instructions Spacemaker®Dishwasher have questions, call 800.GE.CARES or visit our website at: www.GEAppliances.com If you (800.432.2737) BEFORE YOU BEGIN IMPORTANT- The dishwasher MUST be...
-
Page 2: Materials You Will Need
PARTS SUPPLIED IN INSTALLATION Screw Kit PACKAGE: Hex Head Phillips Head [] Two 8-18 × 5/8" Phillips heed wood screws Junction Box Screw Wood Screws [] Junction box cover ond #10 hex heod 1/2" long 5/8" long Junction Box Cover screw Droin hose (78"... -
Page 3: Installation
Installation Preparation-Enclosure • Sink opening for garbage disposer must be PREPARE DISHWASHER ENCLOSURE dimensioned as shown (7-1/2")in Area "C." This will SINK LOCATION provide clearance for disposer and plumbing in • Water line to sink faucet and drain from sink can Area "C"... -
Page 4: Prepare Drain Plumbing
Installation Preparation-Drain PREPARE DRAIN PLUMBING METHOD 1-Air Gap with Waste Tee or Disposer Drain Requirements • Follow local codes and ordinances. • Drain hose must not exceed 10 feet in length. • A high drain loop or air gap is required. See below. Drain Method Figure C The type of drain installation depends on the... -
Page 5: Prepare Electrical Wiring
Installation Preparation-Electrical Supply PREPARE ELECTRICAL WIRING r!_LVAVl.'I fl _11_ [ Cl FOR PERSONALSAFETY:Remove house Alternate fuse or open circuit breaker before Location beginning installation. Do not use an extension cord or adapter plug with this appliance. Receptacle ..l-i/2"_ia. PARA SEGURIDAD PERSONAL: Retire el fusible from 'Cabinet de la casa o abra el interruptor... - Page 6 Installation Preparation-Hot Water Supply PREPARE HOT WATER SUPPLY CAUTION Hot Water Line • The line may enter from either side, rear, or floor The hot water supply line pressure must be at least 20 PSI. Lower pressures could cause the water valve to leak and within the shaded area shown in Figure F.
-
Page 7: Dishwasher Installation
Dishwasher Installation STEP 3: REMOVE WOOD BASE CAUTION IM PO RTANT - Do not kick off wood base! Do not remove the wood bose until you ere reedy Damage will occur. to instell the dishwesher. The dishwasher will tip over when the door is opened if the bose is removed. -
Page 8: Step 5: Install Power Cord
National Electrical Code, Section/422 and/ or local codes and ordinances. Maximum power cord length is 6 feet. Power Cord Kit WX09X70910, Bracket available for purchase from an authorized GE Red Electrical 90 ° Thread Seal Connection Appliance Dealer, meets these requirements. -
Page 9: Power Supply
The GPF65 kit is ovoiloble from outhorized GE opplionce deolers. • Refer to Figure Pond follow the instructions included in Side- the kit. -
Page 10: Step 11: Slide Dishwasher Into Cabinet
Dishwasher Installation STEP 11: SLIDE DISHWASHER INTO CABINET STEP 12: POSITION AND LEVEL DISHWASHER IM PORTANT Do not push against the front IM PORTANT- Dishwasher must be level for panel with knees. Damage will occur. proper dish rack operation, wash performance, and door operation. -
Page 11: Step 14: Connect Water Supply
Dishwasher Installation STEP 14: CONNECT WATER SUPPLY STEP 13: FASTEN DISHWASHER UNDERSIDE OF COUNTERTOP OR SIDES Connect the water supplg line to the 90° elbow OF CABINET installed in Step 6. • Slide the compression nut and then the ferrule over In this step you will need the two 5/8"... -
Page 12: Drain Line
Dishwasher Installation STEP 15: CONNECT DRAIN LINE Method 1 - Air gap with waste tee or disposer The molded end of the drain hose will fit 5/8" _.i___ _/-___ through 1" diameter inlet ports on the air gap, waste tee or disposer. •... -
Page 13: Step 18: Pre-Test Check List
Dishwasher Installation STEP 17: INSTALL JUNCTION BOX COVER STEP 16: CONNECT POWER SUPPLY If junction box cover is already installed, skip to If a power cord with plug is already installed, Step 18. proceed to Step 17. In this step you will need the junction box cover ond If house wiring is not 2-wire with a ground the #10 hex heod screw from the screw kit set oside... - Page 14 Dishwasher Installation - Check the electrical connection to the water STEP 19: DISHWASHER WET TEST valve. The red electrical connector should be CHECK LIST plugged into the dishwasher water valve. If it is [] Turn on power supply or if power cord is used, not plugged in, turn off electrical power to the plug it into the wall outlet.
- Page 15 Dishwasher Installation STEP 20: REPLACE ACCESS PANEL AND STEP 21: LITERATURE TOEKICK [] Leave the Owners' Manual, Installation Instructions, samples, and/or coupons with In this step you will need the panels and the two consumer. screws set aside in Step 4. There are two tgpes of screws used.
- Page 16 SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE GE Consumer & Industrial General Electric Compang Pub. No. 31-30271 Louisville, Kentuckg 40225 Dwg. No. 206C1559P177 ND 06M-2101 (1/07) GEAppliances.com...
-
Page 17: Notice D'installation
' ¸¸¸¸¸ i!!!iiiiiii_ i-i_:i::i l,.ii !!!!ii;:iii:i i:io!i i Appliances Notice d'installation Lave-vaisselle Spacemaker ® En cas de questions, appeler le 800.GE.CARES (800.432.2737) rendre visite _ notre site web : www.GEAppliances.com AVANT DE COMMENCER IM PORTANT - Le lave-vaisselle DOlT atre... - Page 18 PII_CESFOURNIES DANS LE Ensemble de vis N#CESSAIRE D'INSTALLATION cruciforme n ° jonction 6 t6te 6 Deux (2)vis 5 bois 5 t@te cruciforme n° _Visaboisat6te VispourboTtede 8 de 518 po de six pans n ° 8-18 de 5/8 po long "_ 10- 112 po de long Couvercle de boTte...
- Page 19 Preparation pour I'installation - Enceinte PRI:!PARATION DE L'ENCEINTE DU LAVE- • Le diam_tre de I'ouverture du brogeur de d_chets duns I'_vier doit @re de 19 cm (7 1/2 po), comme VAISSELLE ET DE L'EMPLACEMENT DE L'I:!VIER indiqu6 8 lu section C. Ceci permet d'instutler le •...
- Page 20 Preparation pour I'installation - Vidange MISTHODE 1 - Intervalle d'air avec t@de vidage ou PRI_PARATION DE LA PLOMBERIE broyeur de d@chets DE VIDANGE Exigences de vidange • Respecter les codes et r_gtements Iocaux. • Le tuyau de vidange ne peut pas @re plus de 3 m (10 pi)de long.
- Page 21 Preparation pour I'installation - alimentation lectrique LE BRANCHEMENT PRI_PARATION POUR Autre I_LECTRIOUE v!Y-'_ll_l_ll[e]_l " emplacement SI_CURITI_ : Enlever les fusibles ou Troudemax.S8mm JJ / possible de d_brancher le disjoncteur de la maison -Pm-_--/(1-1/2 po)dediam_tre lOcm _ la prise avant de commencer I'installation. Ne pas _I"...
- Page 22 Preparation pour I'installation - Alimentation d'eau chaude PRI_PARATION DE L'ALIMENTATION D'EAU PRUDENCE CHAUDE Lo pression de Io conduite d'olimentotion d'eou choude Tuyau d'eou chaude doit 6tre d'ou moins 1,4 bor (20 psi). Une pression plus • Le tuyau peut entrer d'un c6t_ ou de I'autre, de couser une fuite dons le robinet et des foible risque de...
-
Page 23: Installation Du Lave-Vaisselle
Installation du lave-vaisselle I_TAPE 3 • DISPOSE DE LA PALETTE EN BOIS PRUDENCE IM PORTANT - Ne pas enlever la palette Ne pas enlever la palette en bois avant d'6tre pr6t 6 en donnant des coups de pied ! Ceci risque installer le lave-vaisselle. - Page 24 Lo Iongueur maximale du cordon est de 2 m@res (6 pi). Le kit de cordon d'atimentation WXOgX70910, )art de la vanne en vente che7 les distributeurs agr@@sd'appareils m@nagers GE, satisfait @ces crit@res. Coude 6 @lectrique rouge angle droit de filet de remplissage...
- Page 25 DU CORDON I_LECTRIQUE AU disponible chez les distributeurs agr#es d'appareils TRAVERS DE L'ARMOIRE m#nagers GE. Le tuyau de 3 m porte le num#ro • Redresser le lave-vaisselle et le placer devant piece GPFIOS. I'ouverture de I'armoire. Sice port est Cran d'arr_t de tuyau •...
- Page 26 Installation du lave-vaisselle I_TAPE II" PLACEMENT DU LAVE-VAISSELLE I_TAPE 12 • PLACEMENT ET MISE A NIVEAU DANS L'ARMOIRE DU LAVE-VAISSELLE IM PORTANT IMPORTANT- - Le lave-vaisselle doit atre 6 Ne pas pousser contre le panneau avant avec le genou. Ceci peut causer niveau pour assurer...
- Page 27 Installation du lave-vaisselle I_TAPE 13 : FIXATION DU LAVE-VAISSELLE I_TAPE 14: BRANCHEMENT AU-DESSOUS DU PLAN DE L'ALIMENTATION D'EAU TRAVAIL OU AUX C6TI_S DE Brancher le tuyau d'atimentation d'eau au coude h angle droit instatl_ h I'@ope 6. L'ARMOIRE • Gtisser 1'6crou de compression puis Io bogue sur Dams cette @ape, il faut utiliser les deux vis 6 bois 6 I'extr6mit6 du tugau d'eau.
- Page 28 Installation du lave-vaisselle I_TAPE 15 : BRANCHEMENT DU TUYAU M(_thode 1 - Intervalle d'air avec t6 de vidage broyeur de d6chets VIDANGE L'extr_mit_ mout_e du tuyau de vidange se branche sur des orifices d'admission de 5/8 po 8 1 po de diam_tre de I'intervatle d'air, du t_ de vidange ou du brogeur de d_chets.
- Page 29 (]u blanc et le fit noir (]u noir. [] V_rifier que le chbl(]ge est bien inst(]ll_ sous le I(]ve-v(]isselle, suns _tre pinc_ ou en contQct (]vec Remarque : V_rifier que lesfaisceaux de ills les ressorts de porte ou (]utres pi_ces du lave- passent au travers du petit trou du support vaisselle.
- Page 30 Installation du lave-vaisselle I_TAPE 19 : ESSAI DU LAVE-VAISSELLE AVEC - ContrSter le bronchement _lectrique ou robinet d'eau. Le roccord 61ectrique rouge doit 6tre DE L'EAU bronch6 sur le robinet d'eou du Iove-voisselle. Si ce Hettre le bloc d'atimentation sous tension ou, n'est pas le COS,couper I'alimentotion _lectrique en cos d'utilisation...
- Page 31 Installation du lave-vaisselle I_TAPE 20 : REMISE EN PLACE DU PANNEAU I_TAPE 21 : DOCUMENTATION D'ACCES ET DE LA PLINTHE Leisser le Manuel de I'utilisuteur, lu Notice d'instutlution, les _chuntillons et/ou les coupons Dans cette _tape, il faut utiliser le panneau et les de r_duction uvec le client.
- Page 32 LES DONNEES TECHNIQUES PEUVENT CHANGER SANS PREAVIS GE Consumer & Industrial General Electric Compang Louisville, Kentuckg 40225 Pub. N° de publicution 31-30271 N° de plun 206C1559P203 GE07J-2374 (10/10) GEAppliances.com...