GE Monogram ZV750 Installation Instructions Manual
36" vent hood
Hide thumbs
Also See for Monogram ZV750:
- Installation instructions manual (56 pages) ,
- Owner's manual (32 pages) ,
- Technical service manual (30 pages)
Advertisement
Quick Links
Advertisement
Related Manuals for GE Monogram ZV750
Summary of Contents for GE Monogram ZV750
- Page 1 GE Monogram ® Installation Instructions 36" Vent Hood Model ZV750 Monogram°...
- Page 2 See "Electrical Supply", page 4. I OBSERVE THE FOI,I,OWING: If you have questions concerning installation of tiffs product, call the GE Answer A. Use tiffs unit only in the manner intended Center _> Consumer Information Service at by the manufacturer.
- Page 3 Design Intormation 36" Vent Hood Model Model This vent hood is designed to be used in vented installations. ZV750 Available A decorative duct cover is provided to cover the duct flom tile top of tile hood to an 8 ft.
- Page 4 Design Information 36" Vent Hood ZV750SYInstallationHeights Advance Using Duct Cover Accessories Actual • A duct cover accesso_ y may be required Plannin Ceiling * PossibleHood your hood installation height. Refer to this Duct Cover Heitlht InstallationHeight chart to determine the need for the ZX10SY 7' 11"...
- Page 5 Installation Preparation 36" Vent Hood Duct Use this chart Total compute maximum fittings Equivalent Quantity Equivalent permissable lengths Duct Piece Dimensions I,ength* Used I,ength for duct runs to lit. RotlI](1, outdoors. straight (per foot length) Note: Do not exceed 3-1/4" x l 0" lit.
- Page 6 Installation Preparation 36" Vent Hood 7bols & • Tape measure • Safety glasses • I_dfe • Tape to mount template Materials • Spirit level • Gloves to protect against sharp edges Required • Wire cutter • 120V 60Hz. 15 oI 20 Amp, 2 wire with (not supplied) •...
- Page 7 Installation 36" Vent Hood I,ocate tim hardware accessory box packed with range hood and check contents. Wall 2 Large Check FlatWashers Fasteners Installation 2 Mounting Hardware Brackets Wood Screws Decorative Duct Ph,,,, ead Screws Utility Bars with Screws 3 Filters Wall Mount Template To determine ductwork...
- Page 8 Installation 36" Vent Hood Whenever possible, the vent hood should secured to wall studs. • XVith the template roped in place, use a puncll to mark all mounting screw locations. Install • Drill 1/8" pilot holes at the 6 punched Mounting locations.
- Page 9 Installation 36" Vent Hood Install the 2 small screws into tile sides of tile duct bracket. Remove tile screws. This will insure ease of final installation. Temporarily install a piece of 6" duct cut to Install Duct length between tile hood oudet tile ductwork...
- Page 10 Installation 36" Vent Hood Do not use sheet metal screws at hood flange connection. Doing so will prevent proper Duct Tape damper operation. Seal connection with Over Seam Connect rope only. and Screw Screw Ductwork Install ductwork, making connections direction of airflow as illustrated.
- Page 11 Installation 36" Vent Hood Install Filters • To remove the filters, grasp the knob and Remove protective film on filters. push the filter towards the rear and tilt Tip the filter into the lower slots at the downwards. rear of the opening, lift the filter and pull the knob...
- Page 12 Note: \,_ hile perfl_rming installations described in this book, satety glasses or goggles should be _orn. For ,\hn_ogram local service i_ 3our area, call 1.800.444. 1845. Monogram: NOTE: Product improvement is a contimdng endea\_r at General Electric. There[k_re. materials, appearance specit3cations subject to change...