Page 1
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE. FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 Printed In USA Form No. 769-08270...
See How-to Maintenance and Parts Installation Videos at www.cubcadet.com/tutorials ◊ Call a Customer Support Representative at (800) 965-4CUB ◊ Locate your nearest Cub Cadet Dealer at (877) 282-8684 ◊ Write to Cub Cadet LLC • P.O. Box 361131 • Cleveland, OH • 44136-0019...
Important Safe Operation Practices WARNING! This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury.
Page 4
If your machine is equipped with an internal combustion Never fuel machine indoors. engine and is intended for use near any unimproved forest, Never remove gas cap or add fuel while the engine is brush, or grass covered land, the engine exhaust should be hot or running.
When splitting in the vertical position, stabilize the log Do not alter this machine in any manner, alterations such before moving the control handle. Split as follows: as attaching a rope or extension to the control handle, or adding to the width or height of the wedge may result in Place log on the end plate and turn until it leans personal injury.
Page 6
Safety Symbols This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the machine before attempting to assemble and operate. Symbol Description READ THE OPERATOR’S MANUAL(S) Read, understand, and follow all instructions in the manual(s) before attempting to assemble and operate WARNING—...
Assembly & Set-Up Contents of Carton • One Log Splitter • One Tongue Assembly • One Operator’s Manual • One Engine Operator’s Manual WARNING! Remove the spring clip and clevis pin from the jack stand Use extreme caution unpacking this on the tongue and then pivot the jack stand towards the machine.
Page 8
Align the holes in the tongue with the holes in the tank Disconnect the dislodger from the beam weld bracket by bracket and secure with the hardware just removed. See removing the six hex screws. See Figure 3-4. Figure 3-2. NOTE: The high pressure hose, which runs from the gear pump to the bottom of the control valve, must be above Hex Screws...
Page 9
Lift and slide the cylinder up to the top of beam and into Cut the metal strap securing the log splitter to the bottom the weld brackets. See Figure 3-6. of the crate and remove the wood under the engine and/or any other wood, then roll the log splitter off the bottom of the shipping crate.
Page 10
Set-Up Check the fluid level using the dipstick. See Figure 3-9. Do not overfill. Gas and Oil Fill-Up NOTE: Approved fluids include Shell Tellus® S2 M 32 Hydraulic Fluid, Dexron® III/Mercon® automatic Service the engine with gasoline and oil as instructed in transmission fluid, Pro-Select™...
Controls & Features Cylinder Control Log Dislodger Handle Horizontal Beam Lock Tongue Wedge Beam Log Tray Plate Jack Stand Vertical Beam Lock Engine Controls Log Dislodger See the Engine Operator’s Manual for the location and function The log dislodger is designed to remove any partially split wood of the controls on the engine.
Operation Starting & Stopping the Engine To lock the beam in the vertical position, pull out on the vertical beam lock and rotate it to secure the Refer to the Engine Operator’s manual packed with your log beam. See Figure 5-2. splitter for instructions on starting and stopping the engine.
Page 13
Using the Control Handle To stabilize the log, place your left hand on the side of the log opposite the beam as shown in Figure 5-1. The control handle has three positions. See Figure 5-4. WARNING! Never place a hand on the ends of the log, between the log or end plate and the splitting Neutral wedge.
Operating Tips Transporting the Log Splitter Lower the beam to its horizontal position. Make certain the Always: beam is locked securely with the horizontal beam lock. Use clean fluid and check the fluid level regularly. Remove the spring clip and clevis pin from the jack stand. Use an approved hydraulic fluid.
Maintenance & Adjustments WARNING! Carefully unthread the inlet filter and clean it with Do not make any adjustments without penetrating oil. See Figure 6-1. first stopping the engine, disconnecting the spark plug wire and grounding it against the engine. Always wear safety glasses during operation or while performing any adjustments or repairs.
Page 16
Off-Season Storage Refill the reservoir within range marked on the dipstick. See Figure 6-2. If the log splitter will not be used for more than 30 days, prepare it for storage as follows: Dipstick WARNING! Never store the machine with fuel in the fuel tank inside of building where fumes may reach an open flame or spark, or where ignition sources are present such as hot water and space...
Service Flexible Pump Coupler Align the pump coupling half with the nylon “spider” by rotating the engine using the starter handle. Slide the The flexible pump coupler is a nylon “spider” insert, located coupling half into place while guiding the three mounting between the pump and the engine shaft.
Troubleshooting Problem Cause Remedy Cylinder rod will not move 1. Broken drive shaft. 1. See authorized service dealer. 2. Shipping plugs left in hydraulic hoses. 2. Disconnect hydraulic hoses, remove shipping plugs, reconnect hoses. 3. Set screws in coupling not adjusted properly. 3.
Page 19
Problem Cause Remedy Wood will not split or wood 1. Small gear section damaged. 1. See authorized service dealer. splits too slowly 2. Pump check valve leaking. 2. See authorized service dealer. 3. Excessive pump inlet vacuum. 3. Make certain pump inlet hoses are clear and unblocked.
SNOW THROWERS, CHIPPER-SHREDDERS, CHIPPER-SHREDDER VACUUMS, LOG SPLITTERS AND JET SWEEPS The limited warranty set forth below is given by Cub Cadet LLC with b. Log splitter pumps, valves, and cylinders have a separate one year respect to new merchandise purchased and used in the United States, warranty.
Page 25
LEA Y RESPETE TODAS LAS NORMAS DE SEGURIDAD E INSTRUCCIONES INCLUIDAS EN ESTE MANUAL ANTES DE PONER EN FUNCIONAMIENTO ESTA MÁQUINA. SI NO RESPETA ESTAS INSTRUCCIONES PUEDE PROVOCAR LESIONES PERSONALES. CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 Impreso en Estados Unidos de América Formulario No. 769-08270...
Page 26
Visite nuestro sitio web en www.cubcadet.com Ver Vídeos demostrativos de instalación de mantenimiento y piezas en www.cubcadet.com/Tutorials ◊ Llame a un representante de Asistencia al Cliente al (800) 965-4CUB ◊ Escríbanos a Cub Cadet LLC • P.O. Box 361131 • Cleveland, OH • 44136-0019...
Medidas importantes de seguridad ADVERTENCIA: La presencia de este símbolo indica que se trata de instrucciones de seguridad importantes que se deben respetar para evitar poner en peligro su seguridad personal y/o material y la de otras personas. Lea y cumpla todas las instrucciones de este manual antes de intentar operar esta máquina.
Page 28
Si la máquina está equipada con un motor de combustión Utilice sólo los recipientes para gasolina autorizados. interna y existe la intención de usarla cerca de un terreno Apague todos los cigarrillos, cigarros, pipas y otras agreste cubierto de bosque, arbustos o pasto, el escape del fuentes de ignición.
Page 29
Use únicamente la mano derecha para operar los controles. Periódicamente controle que todas las tuercas y pernos, abrazaderas de mangueras y accesorios hidráulicos estén Nunca intente cortar más de un tronco a la vez. ajustados, para verificar que el equipo se encuentra en Para los registros que no están cortados en ángulo recto, el condiciones de trabajo seguras.
Page 30
Símbolos de seguridad En esta página se presentan y describen los símbolos de seguridad que pueden aparecer en este producto. Lea, entienda y cumpla todas las instrucciones incluidas en la máquina antes de intentar realizar el montaje de la unidad y utilizarla. Símbolo Descripción LEA LOS MANUALES DEL OPERADOR...
Montaje y Configuración Contenido de la caja • Una máquina rompetroncos • Un montaje de lengüeta • Un Manual del operador • Un Manual del operador del motor ¡ ADVERTENCIA! Retire del gato que está sobre la lengüeta la abrazadera de Tenga mucho cuidado al resorte y el pasador de horquilla y luego gire el gato hacia desembalar esta máquina.
Page 32
Alinee los orificios de la lengüeta con los orificios del Desconecte el liberador del soporte soldado de vigueta soporte del tanque y fíjela con los elementos de ferretería retirando los seis tornillos hexagonales. Vea la Figura 3-4. que se acaban de retirar. Vea la Figura 3-2. Tornillos NOTA: La manguera de alta presión, que se extiende desde de cabeza...
Page 33
Levante y deslice el cilindro hacia arriba hasta el tope de la Corte la tira de metal que sujeta la máquina rompetroncos vigueta y dentro de los soportes soldados. Vea la Figura 3-6. a la base de la aja y extraiga la madera que está debajo del motor y/o cualquier otra madera, luego haga rodar la máquina fuera de la base de la caja de embalaje.
Page 34
Presión de los neumáticos Desconecte la bujía y cebe la bomba tirando del arrancador de retroceso hasta el máximo. Repita este paso aproximada- La presión de operación máxima recomendada es 30 psi. En mente 10 veces. ninguna circunstancia supere la presión en psi recomendada por Vuelva a conectar el cable de la bujía y arranque el motor el fabricante.
Controles y Características Manija de control Liberador de Cilindro la madera Bloqueo de la viga horizontal Lengüeta Montaje de la vigueta Fin del mural Cuña Gato Bandeja de troncos Vertical: Vigueta Tuerca Figura 4-1 Controles del motor Liberador de la madera Consulte el manual del motor adjunto para ver la ubicación y el El liberador de madera está...
Funcionamiento Arranque y detención del motor Para trabar la vigueta en posición vertical, tire del bloqueo de vigueta vertical hacia afuera y gírelo para Consulte el manual del operador del motor embalado con la ajustar la vigueta. Vea la Figura 5-2. máquina rompetroncos por las instrucciones sobre cómo arrancar y detener el motor.
Page 37
Uso de la manija de control Cómo cortar madera La manija de control tiene tres posiciones. Vea la Figura 5-4. Ponga en marcha el motor como se indica en el manual del operador del motor que se incluye con la máquina Neutral rompetroncos.
Page 38
Consejos de operación Transporte de la máquina rompetroncos Baje la vigueta a la posición horizontal. Asegúrese de que la Siempre: vigueta esté trabada firmemente con el bloqueo de vigueta horizontal. Use líquido limpio y controle el nivel de líquido periódicamente. Retire la abrazadera de resorte y el pasador de horquilla del gato.
Mantenimiento y Ajustes ¡ADVERTENCIA! Con mucho cuidado desenrosque el filtro de entrada y Siempre detenga el motor, límpielo con aceite penetrante. Vea la Figura 6-1. desconecte el cable de la bujía y haga masa contra el motor antes de realizar cualquier ajuste. Utilice siempre anteojos de seguridad durante el funcionamiento o mientras ajusta o repara este equipo.
Page 40
Almacenamiento fuera de temporada Vuelva a llenar el depósito dentro de los límites marcados en la varilla. Ver Figura 6-2. Si el rompe troncos no se usa por más de 30 días, prepárelo para su almacenamiento de la siguiente manera: Varilla ¡ADVERTENCIA! Nunca almacene la máquina con...
Servicio Acoplador flexible de la bomba Instalación del medio de acoplamiento de la bomba y la llave en el eje de la bomba. Gire la mitad de acoplamiento El acoplador flexible es una bomba de nylon “araña” se añade, hasta que el tornillo de ajuste hacia abajo. No apriete el situada entre la bomba y el eje motor.
Solución de Problemas Problema Causa Solución La varilla del cilindro no se 1. El eje de accionamiento está roto. 1. Consulte al distribuidor de servicio autorizado. mueve 2. Se han dejado los tapones de envío en las 2. Desconecte las mangueras hidráulicas, retire los mangueras hidráulicas.
Page 43
Problema Causa Solución La madera no se parte o se 1. La sección de engranajes pequeños está dañada. 1. Consulte al distribuidor de servicio autorizado. divide la madera con demasiada 2. La válvula de retención de la bomba tiene pérdidas. 2.
Para usos comerciales y aplicaciones: Cub Cadet garantiza este producto (salvo piezas de desgaste normal, como se describe e. Piezas de reemplazo que no son piezas originales de Cub Cadet. más abajo) contra defectos en materiales y mano de obra por un f.