Page 1: Table Of Contents
MODEL 4734 SECURITY SYSTEM OWNER'S MANUAL TABLE OF CONTENTS Page SYSTEM OVERVIEW Introduction System components Features Types of alarms Other audible signals Access codes Model 3825 touchpad System status lights Touchpad function buttons SYSTEM OPERATIONS If you make a mistake...
Page 2 PROGRAMMING Entering programming mode Selecting a menu Viewing menu selections Accept programming changes If you make a mistake while programming Exiting a menu Exit programming mode Time windows (menu 0) Access menu (menu 1) 3.10 Holidays menu (menu 2) 3.11 DST dates (menu 3) IN CASE OF TROUBLE What happens when an alarm occurs...
Page 3: System Overview
4720 security system, designed especially for businesses needing to control access for a large number of users. The 4734 enables you to easily control a large facility with access for 1,000 users and provides your business with dependable, 24-hour protection.
Page 4 Control panel The 4734's control panel is the electronic center of the system, the part housed in the metal cabinet. All sensors, card access stations, and touchpads are connected to the panel.
Page 5: Features
Zones are protection points within your building. A zone can be a room, a section of a room, or a group of rooms. The 4734 allows you to assign up to 80 different zones. Some special types of zones are described below.
Page 6 When the system is disarmed, chime zones emit a warning sound whenever anyone enters them. Multi-area System The 4734 can divide your premises into up to 8 "areas," or groups of zones, that can be armed and disarmed independently. Special menus display on the touchpad allowing you to control your system easily.
Page 7 A programmed number of minutes before the system auto- arms, the touchpads display the number of minutes until arming will occur. The touchpads also beep every 10 seconds during this period. If you are using this feature, your installer will perform the necessary programming.
Page 8: Types Of Alarms
The alarms are ranked in priority order. Fire If the 4734 senses a fire, a high volume, high pitch pulsing alarm will sound and the system will send a fire alarm signal to the central station.
Page 9: Other Audible Signals
Auxiliary Alarms Flooding and furnace failure are two examples of auxiliary alarms. You and your alarm installer will decide if your installation needs any auxiliary alarms. Auxiliary alarms produce alternating high/low pitch pulsed tones. Other Audible Signals Other conditions, besides alarms, that cause audible signals are: Trouble condition A one-second beep every few seconds while a trouble...
Page 10 NOTE 1: Because the main access code can activate the WALK TEST, a system test during which the 4734 is temporarily unable to respond to fire alarms, this code cannot be used by an end-user in a UL commercial fire installation.
Page 11: System Status Lights
Door System Status Alert Tone Sounder (Liquid Crystal Display) Lights READY ARMED BYPS NO DELAY INTERIOR CHIME R E G E N C Y MODEL 4660C CODE MUTE TEST STAT ICOM DOOR FIRE Function Buttons Digit Buttons Function Buttons MODEL 4660C System Status Lights The lights on the top left of the touchpad tell you information about your system, including whether...
Page 12 indicates that some of the areas controlled by this touchpad have not ready zones. ARMED ON - All areas controlled by this touchpad are armed. OFF - All areas controlled by this touchpad are disarmed FLASHING - Some, but not all, areas controlled by this touchpad are armed.
Page 13: Touchpad Function Buttons
OFF - Chime feature disabled. (If the system is armed, an alarm, not a chime tone, sounds when anyone enters the zone.) FLASHING - Some, but not all, areas controlled by this touchpad have the chime feature enabled. Touchpad Function Buttons Some keys, when used for multi-area operation or programming, have different functions than those described here.
Page 14 ICOM Activates the telephone feature. Other Touchpads Other touchpads may be used with the 4734 but these may have slightly different buttons or indicator lights. The differences you will encounter if you are using one of the compatible touchpads are described below.
Page 15 *Model 4433 Touchpad The Model 4433's two keys, when pressed simultaneously, cause a panic alarm. There is no "No Delay" indicator light or button with this model. The key is used for both the Code 2 and Door DOOR functions. The key is used for both the Chime CHIME and Interior functions.
Page 16 Section 2: Access Control Operations NOTE: The Model 4734 Security System is not UL Listed for door access control. Up to 1,000 users can gain access to your secured premises by using card readers or touchpads. Up to 15 doors can be set up as access stations. Card readers can be either the card-swipe or proximity-reader type.
Page 17 If you prefer that system users use only cards, not codes, to access doors, you can program this by selecting a "card only" profile number. See section 4.11 for more information. Technical Manuals Online! - http://www.tech-man.com...
Page 18 Remote Door Access Users can access any door/ touchpad they have been given access from any other door/touchpad. This would be useful, for example, for allowing another person to enter a door after an intercom conversation. Enter the number of the door (1-15). Press (or present your access card).
Page 19: System Operations
Section 3: Other System Operations If You Make a Mistake Press any time to erase an incorrect command. Entering Access Codes Many system operations, including resetting an alarm, bypassing a zone, and conducting a system test require you to enter a valid access code. When you enter your code at a touchpad, you have five seconds to enter each digit.
Page 20 When used in the area menu, most keys have the same function as described in section 1.9, but a few are different. For your convenience, the table below lists all the keys available with the area menu. Function Disarms all areas to which the user has access and returns to the normal operating display.
Page 21: Arming The System Single Area System
Arming the System Single Area System See Section 3.8 for multi-area system information. Make sure the touchpad's green READY light is lit and the ARMED light is off. Enter your access code at any touchpad. When you finish, the green READY light will go off and the ARMED light will go on.
Page 22 Your system will not be fully operational during a trouble condition. Residential System If you are using the 4734 in your home, you may want to follow the procedure below when arming your system. Arm your system when your home is unoccupied or when residents are sleeping.
Page 23: Controlling Auto-Arming
disarm the system. The warning tone will stop as soon as you enter the first digit of your access code. To disarm the system, enter your access code at the touchpad. Controlling Auto-Arming Your system may be programmed for auto-arming. In this case, the entire system or certain areas can be armed or disarmed automatically at specified times.
Page 24 Enter the number of the zone to bypass. Press BYPS If your system is programmed to require an access code, the LCD will display the number of the zone you are attempting to bypass and will prompt you to enter the access code. If, for example, you are attempting to bypass zone 5, the touchpad will display "5-ENTER CODE."...
Page 25: Unbypassing A Zone
Unbypassing a Zone Unbypassing a zone makes it ready once again to detect alarms. Enter the number of the zone to unbypass. Press BYPS If the touchpad displays "RESTRICTED ZONE," you have attempted to unbypass a fire or panic zone or a not ready zone with an armed system.
Page 26: Resetting An Alarm
2 STAT touchpad you are currently using. displays the installed version of the 4734 4 STAT software. Resetting an Alarm To reset an alarm in a single-area system, enter your access code.
Page 27: Viewing Event History
The alarm memory feature records alarm information. Press to display the location of any alarms that have occurred. This function only remembers activity from a single arming period. The next time you arm the system, the memory from the previous period will be erased automatically.
Page 28: Access Codes
Code 2 feature Press followed by your access code to turn the CODE 2 code 2 feature on when arming the system. This will allow secondary code users, (that is, users whose profiles have been enabled for the code 2 feature), to disarm your system one time.
Page 29 If you are using the duress alarm feature, make certain that no access codes begin with the digit(s) you selected as a duress trigger. Write down new access code numbers and keep them in a secure location. Changing a code (or adding a new code) Do not reprogram access codes unless your installer has recommended it.
Page 30 When you are finished making all the changes, press to return to normal operation. MUTE MUTE Deleting an access code (Never delete your main access code Code 1.) An access code is deleted when you clear it from the system without changing it. Here are the steps. Follow steps 1 through 5 for changing an access code.
Page 31: Intercom Operation
Intercom Operation In conjunction with the model 4640 intercom system, the touchpad can be used as an intercom providing two- way or listen-only communications. Two-Way Communication To turn on one intercom only, press the number of the touchpad you wish to call (1-8), then press .
Page 32 Telephone Operation In conjunction with the 4640 intercom system, the touchpad can be used as a hands-free telephone with many features, including, basic operation (place, answer, and hang up a call); redial; mute or place a call on hold; transfer a call to another touchpad; memory dialing; and automatic timeout.
Page 33: Setting The Time (And Date)
To erase a memory phone number (that is, remove it from memory so you can replace it with another number), follow these steps. Press and 1 or 2, depending on which TEL MEM number you want to erase. Press again. Telephone Timeout The programmed telephone timeout function allows you to automatically limit use of the touchpad telephone...
Page 34 Setting the Date You will be prompted to enter the date whenever you reset the time. If the date shown does not need to be changed, press TEST If you need to change the date, enter it in the MM/DD/YY format. Use leading 0's. Press TEST when you finish entering the date.
Page 35: System Testing
Setting (or Clearing) Holiday Status You can select the current day to be a holiday so that it will follow holiday time windows. You can also de- select the current day so that it will not follow holiday time windows. This procedure is a short-cut method that allows you to quickly change holiday status (for example, to allow holiday access).
Page 36 Fire Test Procedure The test described below must be performed weekly in a UL household fire installation. This procedure tests the bell(s) attached to the system using standby power only. Call the central station to inform them that you will be conducting a test.
Page 37: Programming
Section 4. Programming The 4734's user-friendly menu system allows you to easily program some system features directly from the touchpad. The sections below guide you through the steps. Entering Programming Mode To enter programming mode, press plus 1 1 TEST your access code.
Page 38: Exiting A Menu
If you make a mistake while programming and you have not yet pressed , press to restore the TEST MUTE previous selection for the option. If you have already pressed , you must press TEST to exit the current menu, re-enter the correct MUTE menu, and locate the option.
Page 39: Time Windows (Menu 0)
Time Windows (Menu 0) The 4734 allows you to specify 32 time windows, or periods, which you can use to control when users can access the system or when arming/disarming can occur. For auto-arming systems, you can program a delay period which would allow you to cancel the auto-arm or extend the delay period.
Page 40 EXAMPLE: To program Monday through Friday, press 1 2 3 4 5 . When you've finished selecting days for this time window, press TEST . Assigning Days Digit Sunday Monday Tuesday Wednesday Thursday Friday Saturday Holiday Cards/Codes (Menu 1) This menu allows you to program user codes and select "profiles"...
Page 41 "CODE#:__" Enter the number of the user (2-999) that you want to work with. "#2PROFILE:0" Select a profile number for this user. There are 16 possible profiles, numbered 0-15. "#2 CODE:______" Enter a 4 to 6 digit access code for this user. Be sure to record the number in the system data section at the back of this guide.
Page 42 window group for profile 0 and press . If TEST you want the profile to have access any time (no time restrictions), select window group 32, ALWAYS. If you never want the profile to have access to your building, (because, for example, a card has been lost,) select window group 33, NEVER.
Page 43: Holidays Menu (Menu 2)
Press for Yes or for No. Selecting Yes means the profile will be allowed to program cards and codes and all other user-programmable options and perform special system operations, such as the walk test. 11. "CODE 2#0:YES/NO" Press for Yes or for No.
Page 44: Dst Dates (Menu 3)
TEST as many times as necessary to locate the holiday, then make the changes. As with any programming changes you make with the 4734, always press TEST when you're finished. DST Dates (Menu 4)
Page 45: In Case Of Trouble
Section 5: In Case Of Trouble What Happens When an Alarm Occurs If your system goes into alarm, the following things will happen: A loud audible warning will be heard from all system speakers. The touchpad will display the type of alarm, (for example, fire, panic, or police), and the location of the zone where the alarm is occurring.
Page 46: Appendix
worker knows the location of the exit nearest his or her work area. Make sure workers are familiar with and can quickly recognize your system's audible alarm signals. (See section 1.4.) Instruct workers to feel closed doors BEFORE opening them. If a door is warm, DO NOT OPEN IT. Use an alternate route, such as through a bedroom window.
Page 47 ACCT COMP COMPANY X VICE PRES RECEP GARAGE BOILER ROOM INTERIOR DOOR SENSORS EXTERIOR DOOR & WINDOW SENSORS SMOKE ALARMS HEAT SENSORS MOTION DETECTORS Technical Manuals Online! - http://www.tech-man.com...
Page 48: Lcd Display Messages
LCD Display Messages Message What it Means NORMAL SYSTEM MESSAGES ZONE BYPASS A zone has been bypassed. DOOR BYPASS A door has been bypassed. ZONE DOOR Both doors and zones have been bypassed. BYPASS CODE 2 Users with secondary codes can disarm the system. *FIRE ALARM A zone is in alarm.
Page 49: System Data
System Data Keep the following code numbers and information confidential and stored in a safe place. System installation company: ____________________________________ Name of installer: _____________________________________________ For service, call: ______________________________________________ Before testing, call: ____________________________________________ Your account # is: _____________________________________________ Your central station password is: _________________________________ Number of seconds programmed for exit delay: ______________________ Number of seconds programmed for entry delay: _____________________ Begin recording your access codes on the next page.
Page 50 11. ____________________________ 26. ___________________________ 12. ____________________________ 27. ___________________________ 13. ____________________________ 28. ___________________________ 14. ____________________________ 29. ___________________________ 15. ____________________________ 30. ___________________________ (continued on next page) Technical Manuals Online! - http://www.tech-man.com...
Page 51 Zone locations (continued) 31. ____________________________ 56. ___________________________ 32. ____________________________ 57. ___________________________ 33. ____________________________ 58. ___________________________ 34. ____________________________ 59. ___________________________ 35. ____________________________ 60. ___________________________ 36. ____________________________ 61. ___________________________ 37. ____________________________ 62. ___________________________ 38. ____________________________ 63. ___________________________ 39. ____________________________ 64. ___________________________ 40. ____________________________ 65. ___________________________ 41.
Page 52 51. ____________________________ 76. ___________________________ 52. ____________________________ 77. ___________________________ 53. ____________________________ 78. ___________________________ 54. ____________________________ 79. ___________________________ 55. ____________________________ 80. ___________________________ Technical Manuals Online! - http://www.tech-man.com...
Page 53 Time Windows In this space, your installer can note the time windows that have been set up for your system. Time Window Start Days S M T W TH F S H S M T W TH F S H S M T W TH F S H S M T W TH F S H S M T W TH F S H...
Page 54 S M T W TH F S H S M T W TH F S H S M T W TH F S H S M T W TH F S H S M T W TH F S H S M T W TH F S H S M T W TH F S H S M T W TH F S H...
Page 55 Window Groups Use this form to record which time windows have been assigned to which groups. Window Group # Windows Technical Manuals Online! - http://www.tech-man.com...
Page 56 Technical Manuals Online! - http://www.tech-man.com...
Page 57 User Profiles You can use this form to record the options available to each profile. High Card Areas Door Bypass Disarm Code 2 Sec. Only 1 2 3 4 5 6 7 8 Y / N Y / N Y / N Y / N Y / N Y / N...
Page 58 1 2 3 4 5 6 7 8 Y / N Y / N Y / N Y / N Y / N Y / N Y / N 1 2 3 4 5 6 7 8 Y / N Y / N Y / N Y / N...
Page 59 X-10 Compatible Module Data If your installation uses X-10 compatible modules for automatic control of devices, such as doors, lights, and so on, your installer will record here the keystrokes necessary to activate each doors/devices. To Activate Press Device House code Unit 1 0 1 DOOR 1 0 2 DOOR...
Page 60 X-10 Compatible Module Data (continued) To Activate Press Device House code Unit 2 0 1 DOOR 2 0 2 DOOR 2 0 3 DOOR 2 0 4 DOOR 2 0 5 DOOR 2 0 6 DOOR 2 0 7 DOOR 2 0 8 DOOR 2 0 9 DOOR 2 1 0 DOOR...
Page 61: Quick Reference Guide
Regency 4734 Security System Quick Reference Guide ACCESS OPERATIONS ACCESS A DOOR Present your card or tag within 6 inches of proximity reader Swipe your card through the slot in the card reader Press DOOR + valid ID code at a touchpad.
Page 62 CHANGE AN ACCESS CODE 1. Press 7 TEST . 2. Select Yes or No for Bulk Load. 3. Enter # of user you want to change (2-999). 4. Press CLR + New access code + TEST 5. Press MUTE MUTE DELETE AN ACCESS CODE 1.
Page 63 SILENCE TROUBLE MUTE MUTE TEST OVERALL SYSTEM TEST + Access code MULTI-AREA SYSTEM OPERATIONS DISARM ALL AREAS/RESET Access code + 0 ALARM TOGGLE ARM/DISARM 1. Access code 2. TEST (as many times as necessary until area you want to select displays) 3.

Regency 4734 Owner's Manual

System Overview

System Operations

Programming

In Case of Trouble

Appendix

Quick Links

TABLE OF CONTENTS

Related Manuals for Regency 4734

Summary of Contents for Regency 4734

Table of Contents