Related Manuals for HP C6388B
Summary of Contents for HP C6388B
-
Page 1: User Manual
C6388B Desktop C6389A Rack-Ready C6390A Desktop C6391A Rack-Ready C6394B Desktop C6395A Rack-Ready C6396A Desktop C6397A Rack-Ready HP SCSI Disk Drives User Manual English Japanese... - Page 3 HP C6388B HP C6389A HP C6390A HP C6391A HP C6394B HP C6395A HP C6396A HP C6397A User Manual SCSI Disk Drives Desktop & Rack-Ready Models...
- Page 5 3. HP does not warrant that the operation of HP products will be uninterrupted or error free. If HP is unable, within a reasonable time, to repair or replace any product to a condition as warranted, customer will be entitled to a refund of the purchase price upon prompt return of the product.
- Page 6 9. TO THE EXTENT ALLOWED BY LOCAL LAW, THE REMEDIES IN THIS WARRANTY STATEMENT ARE CUSTOMER’S SOLE AND EXCLUSIVE REMEDIES. EXCEPT AS INDICATED ABOVE, IN NO EVENT WILL HP OR ITS SUPPLIERS BE LIABLE FOR LOSS OF DATA OR FOR DIRECT, SPECIAL,...
- Page 7 Reproduction, adaptation, or translation without prior written permission is prohibited, except as allowed under the copyright laws. © Copyright 1998 Hewlett-Packard Company All rights reserved Publication number C6388-90001 Applicable Products: HP C6388B HP C6389A HP C6390A HP C6391A HP C6394B HP C6395A HP C6396A HP C6397A...
- Page 8 Whenever it is likely that the protection has been impaired, disconnect the power cord until the ground has been restored. Servicing Any servicing, adjustment, maintenance, or repair must be performed by HP authorized and trained service personnel. Support...
-
Page 9: Regulatory Information
Regulatory Information Federal Communications Commission (FCC) Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. -
Page 10: Declaration Of Conformity
Mountain View, CA 94043 U.S.A. Declares that the product Product Name: External Desktop Mass Storage Devices Product Type: Disk Drives C6388B, C6389A, C6390A, C6391A, C6394B, C6395A, C6396A, Model Numbers: C6397A Product Options: Conforms to the following Product Specifications: Safety: IEC 950:1991+A1+A2+A3+A4... - Page 11 Japan VCCI Class B ITE English Translation This equipment is in the Class B category information technology equipment based on the rules of Voluntary Control Council for Interference by Information Technology Equipment (VCCI). Although aimed for residential area operation, radio interference may be caused when used near a radio or TV receiver.
-
Page 13: Table Of Contents
Table of Contents 1. Overview ....................1-1 2. Disk Installation ..................2-1 1. Contents of the Kit for Desktop Models ..........2-1 2. Environment ..................2-2 3. Check Your SCSI Cable ..............2-2 4. Operating System Compatibility ............2-2 5. Set the SCSI ID Selector Switch ............2-3 6. -
Page 15: Overview
HP’s Desktop and Rack-Ready Disk Drives provide a wide range of storage flexibility and reliability: • HP offers a boot capable disk storage solution beginning with the HP C6388B Desktop 4GB drive to the HP C6396A Desktop 9GB disk drive. - Page 16 1-2 Overview...
-
Page 17: Disk Installation
Disk Installation 1. Contents of the Kit for Desktop Models Ensure that the kit contains the following parts: q Desktop Disk Drive q Rubber Feet for Stand q Stand for Vertical Mounting q Power Cord q User Manual Figure 2-1 Kit Contents Disk Installation 2-1... -
Page 18: Environment
The HP C4318B 3U-4Bay Rack Mount Kit allows you to rack mount up to four HP disk drives into a standard HP 19-inch EIA rack. The C4317A 2U 2- Bay Rack Mount Kit has a two drive capacity. See the specifications in Appendix B for more details. -
Page 19: Set The Scsi Id Selector Switch
5. Set the SCSI ID Selector Switch Follow the instructions about checking the SCSI IDs in your system owner’s guide to determine which SCSI IDs are in use on your system. Your external disk drive ships preset to SCSI ID 5. If your system already uses a SCSI device set to ID 5, change the SCSI ID of your drive to an unused ID. -
Page 20: Mount Your Drive Vertically (Optional)
6. Mount Your Drive Vertically (Optional) Your HP desktop disk drive can be used in a vertical or horizontal position, as shown in Figure 2-3. Always use the supplied stand when using the drive in the vertical position. Figure 2-3 Examples of Drive Configuration... - Page 21 If you wish to mount your disk drive in the vertical position, perform the following steps: A. Remove the backing from the four rubber feet and install them on the stand. Figure 2-4 Attaching the Rubber Feet B. Slide the notches in the foot over the pins on the bottom of the stand. Swing up the foot to lock the pieces together.
-
Page 22: Connect The Scsi Cable
C. Insert the corner of the disk unit into the rear of the stand, then swing the unit down to lock it into the stand. Figure 2-6 Inserting the Drive into the Stand 7. Connect the SCSI Cable You can connect the disk drive directly to your system or to another external SCSI device that is connected to your system. -
Page 23: Connect The Power Cable
SCSI Terminator (SE or Differential) SCSI Label SCSI DIFF SCSI Cable FAST WIDE–DIFF SCSI SCSI WIDE–SE / NARROW–SE SCSI Figure 2-7 Connecting the SCSI Cable 8. Connect the Power Cable CAUTION To ensure optimal performance, use the 3-wire power cord supplied with this unit. -
Page 24: Power On The Unit
11. Rack Mounting The Rack-Ready Drives can be mounted into a standard HP 19-inch rack by using the optional HP C4317A (2 EIA units) or the C4318B (3 EIA units) rack mount kits. See Appendix B for more details. 2-8 Disk Installation... -
Page 25: Appendix A: Specifications
Wide SCSI Single-Ended, Dual High-Density 68-pin HP 9000 Workstations & Servers: Supported on HP-UX Boot Disk Exceptions 9.XX – 10.01 as data disks only. For HP-UX 10.10 and above as data or boot disk. Rated A/C Input 100-240V 50/60Hz. Max 1.2A A/C Current Draw Typical: 0.4 A - 0.2 A... - Page 26 Fast Wide SCSI-3 Differential, Dual High-Density 68-pin HP 9000 Workstations: Supported on HP-UX 9.XX as data Boot Disk Exceptions disks only. For HP-UX 10.XX and above as data or boot disk. A/C Input Characteristics 100-240V 50/60Hz. Max 1.2A A/C Current Draw Typical: 0.4 A - 0.2 A...
- Page 27 Wide SCSI Single-Ended, Dual High-Density 68-pin HP 9000 Workstations & Servers: Supported on HP-UX Boot Disk Exceptions 9.XX – 10.01 as data disks only. For HP-UX 10.10 and above as data or boot disk. A/C Input Characteristics 100-240V 50/60Hz. Max 1.2A A/C Current Draw Typical: 0.4 A - 0.2 A...
- Page 28 Table 4: C6396A Desktop and C6397A Rack-Ready 9GB Fast Wide Differential Disk Drive Physical Dimensions 62mm(H) x 215mm(W) x 273mm(D) Weight 2.8kg (6.1 lbs) Data Interface Fast Wide SCSI Differential, Dual High-Density 68-pin Boot Disk Exceptions Boot capable on all supported operating systems. A/C Input Characteristics 100-240V 50/60Hz.
-
Page 29: Appendix B: Rack-Ready Modules
The 3U 4-Bay Rack Kit is designed for mounting into 1.1-meter, 1.6-meter, and 2.0-meter HP 19-inch racks. The HP C4317A (2 EIA units) and C4318B (3 EIA units) are designed for horizontal mounting of four half-height products. These rack enclosures include blind-mate, easy plug connectors providing easy installation and removal of Rack-Ready Modules. - Page 30 I/O plugs. Slide the drive out of the enclosure, using both hands to grasp the unit. Note For comprehensive installation instructions see HP 3U 4-Bay Rack Enclosure Installation Guide (HP part number C4318-90001) or HP 2U 2-Bay Rack Enclosure Installation Guide (HP part number C4317-90002). B-2 Rack-Ready Modules...
- Page 31 2.0m C2906A *All HP rack-ready devices connect to the rack enclosure through a blind- mate, easy-plug connector. The connectors on the back of the rack enclosure are all 68-pin. To connect a device in your rack enclosure with the host system, you may need either a 50-pin or 68-pin cable depending on the type of bus used by the host system.
-
Page 32: Appendix C: Cable Accessories
If your drive is the only SCSI device or if it is the last SCSI device in a daisy- chain of devices, you must install a terminator. C-2 Cable Accessories... - Page 34 Copyright 1998 © Hewlett-Packard Company Printed in USA 07/98 Manual Part No. C6388-90001 * C6388-90001 *...