Grizzly G9004 Instruction Manual
  1. Manuals
  2. Brands
  3. Grizzly Manuals
  4. Planer
  5. G9004
  6. Instruction manual
Grizzly G9004 Instruction Manual

Grizzly G9004 Instruction Manual

3 1/2" portable planer
Hide thumbs Also See for G9004:
Table of Contents

Advertisement

Quick Links

Download this manual
1
3
⁄
" PORTABLE PLANER
2
MODEL G9004
INSTRUCTION MANUAL
COPYRIGHT ©2000 BY GRIZZLY INDUSTRIAL, INC.
1821 VALENCIA ST., BELLINGHAM, WA 98227
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
MARCH, 2000 PRINTED IN U.S.A.

Advertisement

Table of Contents
loading

Related Manuals for Grizzly G9004

Summary of Contents for Grizzly G9004

  • Page 1 INSTRUCTION MANUAL COPYRIGHT ©2000 BY GRIZZLY INDUSTRIAL, INC. 1821 VALENCIA ST., BELLINGHAM, WA 98227 WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. MARCH, 2000 PRINTED IN U.S.A.

  • Page 3: Safety Instructions For Power Tools

    Keep work area well lighted. G9004 Portable Planer SAFETY Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury.
  • Page 4 A guard or other part that is damaged should be properly repaired or replaced. UNATTENDED. TURN POWER OFF. Don’t leave tool until it comes to a complete stop. G9004 Portable Planer PARTS.
  • Page 5 ENSURE PLANER IS PROPERLY ADJUSTED BEFORE STARTING. Always use a test piece to check the adjustment and operation before starting on the actual workpiece. G9004 Portable Planer DO NOT REMOVE EXCESSIVE AMOUNTS OF WOOD IN A SINGLE PASS. Better results...

  • Page 6: Control Location

    Wrench, Sharpening Jig, Blade Setting Jig, Replacement Belt and Replacement Motor Brushes ON/OFF Trigger Fig 1. Location of controls. ⁄ HP, 110V, 5.0 Amp ⁄ " ⁄ " Trigger Lock Rear Foot Belt Cover Fence G9004 Portable Planer ⁄ "...
  • Page 7 Move the straight- edge back and forth across the width of the blade to make sure G9004 Portable Planer the amount of contact is the same all the way across. 3. If there is too much contact, or...

  • Page 8: Blade Installation

    Cutterhead. See Figure 5. Fig 5. Inserting blade assembly on Blade Assembly and line up the three mounting holes. Install three hex head bolts and washers, and tighten with the supplied T-handle wrench. blade. G9004 Portable Planer Plate...

  • Page 9: Blade Sharpening

    Planer and from the Back Plate in order for it to be safely sharpened. Follow the preceding instructions for Blade Removal. The blade set in the G9004 Planer is reversible, so that once one side becomes dull, the blade can be simply reversed to provide a new cutting edge.
  • Page 10 The Planer can be used to cut right down to a scribe line by taking selective cuts This Planer can also be used for face plan- ing, that is, to clean up the rough surface of a board.
  • Page 11 See Figure 7. Be sure the workpiece is firmly secured with clamps or other holding devices. Start the Planer and let it get to full speed before moving the Cutterhead into the workpiece. Apply steady, even pressure and keep the Planer moving along the edge.

  • Page 12: Maintenance

    Insert the new brush, check to make sure it goes into the slot and comes out against the commutator. 5. Replace the brush cover. 6. Repeat for the other brush. 7. Replace the motor cover. Fig 10. Replacing motor brushes. G9004 Portable Planer...

  • Page 13: Operating Tips

    Always have this device serviced by a qualified electri- cal repair technician. Serious injury will result. G9004 Portable Planer Operating this equipment has the potential to propel debris into the air which can cause eye injury. Always wear safety glasses or goggles when operating equipment.
  • Page 14 NOTES G9004 Portable Planer...

  • Page 15: Troubleshooting

    Planer starts, cutter- head turns, no cut. Rough or fuzzy cut. Cut not smooth or straight. G9004 Portable Planer POSSIBLE CAUSE 1. Low voltage. 2. Brushes worn or sticking. 3. Open circuit in motor or loose connections.
  • Page 16 G9004 Portable Planer...
  • Page 17 035 P9004035 Washer 036 P9004036 Depth Set Knob 037 P9004037 Scale 038 P9004038 Washer 039 P9004039 Thrust Washer G9004 Portable Planer Ref. # Part # Description 040 P9004040 Trigger/Switch 041 P9004041 Noise Suppressor 042 P9004042 Terminal 043 P9004043 Cord Assembly...

  • Page 18: Warranty And Returns

    WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main- tenance.

  • Page 19: Warranty Card

    14. Do you think your purchase represents good value? 15. Would you recommend Grizzly to a friend? 16. Would you allow us to use your name as a refer- ence for Grizzly customers in your area? Note: We never use names more than three times. 17.Comments:________________________________...
  • Page 20 Send a Grizzly Catalog to a friend: Name________________________________ Street________________________________ City______________State______Zip_______ FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE...

Table of Contents