Page 2
Acknowledgments AMI is a registered trademark of American Megatrends Inc. PS/2 is a trademark of International Business Machines Corporation. ® Intel and Intel 4th Generation Core DC/QC Processor are registered trademarks of Intel Corporation. Microsoft Windows is a registered trademark of Microsoft Corporation.
The Q87 platform is made with 22-nanometer technology that supports Intel’s first processor architecture to unite the CPU and the graphics core on the transistor level. The MB980 ATX board utilizes the dramatic increase in performance provided this Intel’s latest cutting-edge technology.
INTRODUCTION Checklist Your MB980 package should include the items listed below. The MB980 ATX motherboard This User’s Manual 1 CD containing chipset drivers and flash memory utility Serial ATA cable MB980 User’s Manual...
2x5 pin-header x4 for 8 ports USB; 2x5 pin-header for front panel audio Connector 4x10 box-header for COM3 (RS232) ~ COM6 (RS232) 2x5 pin-header for Digital IO Yes (256 segments, 0, 1, 2…255 sec/min) Watchdog Timer System Voltage Others LAN Wakeup, vPro Board Size 305mm x 244mm MB980 User’s Manual...
INSTALLATIONS Installations This section provides information on how to use the jumpers and connectors on the MB980 in order to set up a workable system. The topics covered are: Installing the CPU ................5 Installing the Memory ................7 Setting the Jumpers ................8 Connectors on MB980 ...............
INSTALLATIONS Installing the CPU The MB980 board supports an LGA1150 Socket (shown below) for Intel Sandy Bridge processors. To install the CPU, unlock first the socket by pressing the lever sideways, then lift it up to a 90-degree. Then, position the CPU above the socket such that the CPU corner aligns with the gold triangle matching the socket corner with a small triangle.
INSTALLATIONS Installing the Memory The MB980 board supports four DDR3 memory socket for a maximum total memory of 32GB in DDR3 DIMM memory type. Installing and Removing Memory Modules To install the DDR3 modules, locate the memory slot on the board and perform the following steps: 1.
INSTALLATIONS Setting the Jumpers Jumpers are used on MB980 to select various settings and features according to your needs and applications. Contact your supplier if you have doubts about the best configuration for your needs. The following lists the connectors on MB980 and their respective functions.
INSTALLATIONS Connectors on MB980 Connector Locations on MB980 ............14 CN2: COM1 and COM2 Serial Ports ..........15 CN3: DVI-D and DVI-I Connector ............ 15 CN5: USB2.0 Connector ..............16 CN1: Display Port Connector ............16 CN7: Gigabit LAN (Intel I217LM) + USB 0/1 ........16 CN6: Gigabit LAN (Intel I211AT) + USB 2/3 ........
DATA 5- DDC CLOCK DATA 5+ DDC DATA SHIELD CLK VSYNC CLOCK + DATA 1- CLOCK - DATA 1+ SHIELD 1/3 Green DATA 3- Blue DATA 3+ HSYNC DDC POWER A GROUND2 A GROUND 1 A GROUND3 MB980 User’s Manual...
J1: Audio Pin Header for Chassis Front Panel Signal Name Pin # Pin # Signal Name MIC IN_L Ground MIC IN_R LINE_R Sense Ground Sense LINE_L Sense Ground J2: SPDIF I/O Pin # Signal Name SPDIF IN Ground SPDIF OUT Ground MB980 User’s Manual...
This connector supplies the CPU operating voltage. Pin # Signal Name Ground Ground +12V +12V J4, J5, J6, J7: COM3~COM6 RS232 Serial Ports Signal Name Pin # Pin # Signal Name DCD# DSR# RTS# SOUT CTS# DTR# MB980 User’s Manual...
INSTALLATIONS J9, J11, J15, J17: USB Connectors Signal Name Pin # Pin # Signal Name J8: Digital I/O Signal Name Pin # Pin # Signal Name OUT3 OUT1 OUT2 OUT0 MB980 User’s Manual...
Pin # Signal Name 3.3V 3.3V -12V 3.3V Ground Ground PS-ON Ground Ground Ground Ground Ground Power good 5VSB +12V +12V Ground +3.3V CPU_FAN1: CPU Fan Power Connector Pin # Signal Name Ground +12V Rotation detection Control MB980 User’s Manual...
INSTALLATIONS SYS_FAN1: System Fan1 Power Connector Pin # Signal Name Ground +12V Rotation detection SYS_FAN2: System Fan2 Power Connector Pin # Signal Name Ground +12V PCIE3: PCI-E X16 Slot MB980 User’s Manual...
These defaults have been carefully chosen by both AMI and your system manufacturer to provide the absolute maximum performance and reliability. Changing the defaults could cause the system to become unstable and crash in some cases. MB980 User’s Manual...
F3: Optimized Default SERR# Generation Disabled F4: Save ESC: Exit ► PCI Express Settings Above 4G Decoding Enables or Disables 64bit capable devices to be decoded in above 4G address space (only if system supports 64 bit PCI decoding). MB980 User’s Manual...
Restore PCIE Registers Disabled Relaxed Ordering Enables or disables PCI Express Device Relaxed Ordering. Extended Tag If ENABLED allows device to use 8-bit Tag field as a requester. No Snoop Enables or disables PCI Express Device No Snoop option. MB980 User’s Manual...
Page 34
On non-PCI Express aware OS’s (Pre Windows Vista)some devices may not be correctly reinitialized after S3.Enabling this restors PCI Express device configuration on S3 resume Warning : Enabling this may cause issues with other hardware after S3 resume. MB980 User’s Manual...
OS. ACPI Sleep State Select ACPI sleep state the system will enter, when the SUSPEND button is pressed. Lock Legacy Resources Enabled or Disabled Lock of Legacy Resources. S3 Video Repost Enable or disable S3 Video Repost. MB980 User’s Manual...
Disabled → ← Select Screen ↑↓ Select Item Enter: Select Change Field F1: General Help F2: Previous Values F3: Optimized Default F4: Save ESC: Exit Wake on PCIE PME Wake Event The options are Disabled and Enabled. MB980 User’s Manual...
OS (Windows Server 2003 SP1, Windows XP SP2, SuSE Linux 9.2, Re33dHat Enterprise 3 Update 3.) Intel Virtualization Technology When enabled, a VMM can utilize the additional hardware capabilities provided by Vanderpool Technology. MB980 User’s Manual...
Eup/Erp specification .[Ethernet Only] Only provide the standby power for Ethernet chip.[Disabled] Shutdown all of the standby power. ISmart Controller Setup the power on time for the system. Schedule Slot 1 / 2 Setup the hour/minute for system power on. MB980 User’s Manual...
Set timer to wait before sending ASF_GET_BOOT_OPTIONS. Activate Remote Assistance Process Trigger CIRA boot. PET Progress User can Enable/Disable PET Events progress to receive PET events or not. Watchdog Timer This configuration is supported only with MB980VF (with iAMT function). Enable/Disable Watchdog Timer. MB980 User’s Manual...
DISABLE option will keep USB devices available only for EFI applications. USB3.0 Support Enable/Disable USB3.0 (XHCI) Controller support. XHCI Hand-off This is a workaround for OSes without XHCI hand-off support. The XHCI ownership change should be claimed by XHCI driver. MB980 User’s Manual...
Page 42
Maximum time the device will take before it properly reports itself to the Host Controller. ‘Auto’ uses default value: for a Root port it is 100ms, for a Hub port the delay is taken from Hub descriptor. MB980 User’s Manual...
► Serial Port 5 Configuration F4: Save ESC: Exit ► Serial Port 6 Configuration Serial Port Configuration Set Parameters of Serial Ports. User can Enable/Disable the serial port and Select an optimal settings for the Super IO Device. MB980 User’s Manual...
Page 44
PC health status. Fan1/Fan2/Fan3 Smart Fan Control This field enables or disables the smart fan feature. At a certain temperature, the fan starts turning. Once the temperature drops to a certain level, it stops turning again. MB980 User’s Manual...
SLP_LAN# Low on DC Power Enable or Disable SLP_LAN# Low on DC Power GP27 Wake From DeepSx Wake from DeepSx by the assertion of GP27 pin SLP_S4 Assertion Width Select a minimum assertion width of the SLP_S4# signal. MB980 User’s Manual...
Enable or disable PCI Express Clock Gating for each root port. DMI Link ASPM Control The control of Active State Power Management on both NB side and SB side of the DMI link. PCIe-USB Glitch W/A PCIe-USB Glitch W/A for bad USB device(s) connected behind PCIE/PEG port. MB980 User’s Manual...
ESC: Exit USB Precondition Precondition work on USB host controller and root ports for faster enumeration. xHCI Mode Mode of operation of xHCI controller. USB Ports Per-Port Disable Control Control each of the USB ports (0~13) disabling. MB980 User’s Manual...
Enabled Azalia will be unconditionally be enabled. Auto = Azalia will be enabled if present, disabled otherwise. Azalia Docking Support Enable or Disable Azalia Docking Support of Audio Controller. Azalia PME Enable or Disable power Management capability of Audio Controller. MB980 User’s Manual...
Page 50
F3: Optimized Default ► Memory Configuration F4: Save ESC: Exit VT-d Check to enable VT-d function on MCH. Enable NB CRID Enable or disable NB CRID WorkAround. C-State Pre-Wake Controls C-State Pre-Wake feature for ARAT, in SSKPD[57]. MB980 User’s Manual...
Keep IGD enabled based on the setup options. DVMT Pre-Allocated Select DVMT 5.0 Pre-Allocated (Fixed) graphics memory size used by the internal graphics device. DVMT Total Gfx Mem Select DVMT 5.0 total graphics memory size used by the internal graphics device. MB980 User’s Manual...
2048 MB (DDR3) Enter: Select CAS Latency (tCL) Change Field F1: General Help Minimum delay time CAS to RAS (tRCDmin) F2: Previous Values F3: Optimized Default Row Precharge (tRPmin) Active to Precharge (tRASmin) F4: Save ESC: Exit MB980 User’s Manual...
Enables/Disables Quiet Boot option. Fast Boot Enables/Disables boot with initialization of a minimal set of devices required to launch active boot option. Has no effect for BBS boot options. Boot Option Priorities Sets the system boot order. MB980 User’s Manual...
Controls the execution of UEFI and Legacy Storage OpROM. Launch Video OpROM policy Controls the execution of UEFI and Legacy Video OpROM. Other PCI device ROM priority For PCI devices other than Network, Mass storage or Video defines which OpROM to launch. MB980 User’s Manual...
The password length must be F1: General Help in the following range: F2: Previous Values Minimum length F3: Optimized Default Maximum length F4: Save ESC: Exit Administrator Password User Password Administrator Password Set Setup Administrator Password. User Password Set User Password. MB980 User’s Manual...
Discard Changes done so far to any of the setup options. Restore Defaults Restore/Load Defaults values for all the setup options. Save as User Defaults Save the changes done so far as User Defaults. Restore User Defaults Restore the User Defaults to all the setup options. MB980 User’s Manual...
LAN Drivers Installation ..............61 Intel® Management Engine Interface ..........64 Intel® USB 3.0 Drivers ..............66 IMPORTANT NOTE: After installing your Windows operating system, you must install first the Intel Chipset Software Installation Utility before proceeding with the drivers installation. MB980 User’s Manual...
Plug & Play INF support for Intel chipset components. Follow the instructions below to complete the installation. 1. Insert the DVD that comes with the board. Click Intel and then Intel(R) 8 Series Chipset Drivers. 2. Click Intel(R) Chipset Software Installation Utility. MB980 User’s Manual...
Page 59
4. Click Yes to accept the software license agreement and proceed with the installation process. 5. On the Readme File Information screen, click Next to continue the installation. 6. The Setup process is now complete. Click Finish to restart the computer and for changes to take effect. MB980 User’s Manual...
DRIVER INSTALLATION VGA Drivers Installation 1. Insert the DVD that comes with the board. Click Intel and then Intel(R) 8 Series Chipset Drivers. 2. Click Intel(R) Core(TM) i3/i5/i7 Graphics Driver. MB980 User’s Manual...
Page 61
DRIVERS INSTALLATION 3. When the Welcome screen appears, click Next to continue. 4. Click Yes to to agree with the license agreement and continue the installation. MB980 User’s Manual...
DRIVER INSTALLATION 5. On the screen shown below, click Install to continue. 6. Setup complete. Click Finish to restart the computer and for changes to take effect. MB980 User’s Manual...
DRIVERS INSTALLATION Realtek HD Audio Driver Installation 1. Insert the DVD that comes with the board. Click Intel and then Intel(R) 8 Series Chipset Drivers. 2. Click Realtek High Definition Audio Driver. MB980 User’s Manual...
Page 64
DRIVER INSTALLATION 3. On the Welcome to the InstallShield Wizard screen, click Yes to proceed with and complete the installation process. 4. The InstallShield Wizard Complete. Click Finish to restart the computer and for changes to take effect. MB980 User’s Manual...
DRIVERS INSTALLATION LAN Drivers Installation 1. Insert the DVD that comes with the board. Click Intel and then Intel(R) 8 Series Chipset Drivers. 2. Click Intel(R) PRO LAN Network Driver. MB980 User’s Manual...
Page 66
DRIVER INSTALLATION 3. Click Install Drivers and Software. 4. When the Welcome screen appears, click Next. MB980 User’s Manual...
Page 67
6. Click the checkbox for Drivers in the Setup Options screen to select it and click Next to continue. 7. The wizard is ready to begin installation. Click Install to begin the installation. 8. When InstallShield Wizard is complete, click Finish. MB980 User’s Manual...
Intel® Management Engine Interface Follow the steps below to install the Intel Management Engine. 1. Insert the DVD that comes with the board. Click Intel and then Intel(R) 8 Series Chipset Drivers and then Intel(R) AMT 9.0 Drivers. MB980 User’s Manual...
Page 69
Management Engine Components, click the checkbox for Install Intel® Control Center & click Next. 3. Click Yes to to agree with the license agreement. 4. When the Setup Progress screen appears, click Next. Then, click Finish when the setup progress has been successfully installed. MB980 User’s Manual...
DRIVER INSTALLATION Intel® USB 3.0 Drivers 1. Insert the DVD that comes with the board. Click Intel and then Intel(R) 8 Series Chipset Drivers. 2. Click Intel(R) USB 3.0 Drivers. MB980 User’s Manual...
Page 71
DRIVERS INSTALLATION 3. When the Welcome screen to the InstallShield Wizard for Intel® USB 3.0 eXtensible Host Controller Driver, click Next. 4. Click Yes to to agree with the license agreement and continue the installation. MB980 User’s Manual...
Page 72
5. On the Readme File Information screen, click Next to continue the installation of the Intel® USB 3.0 eXtensible Host Controller Driver. 6. Setup complete. Click Finish to restart the computer and for changes to take effect. MB980 User’s Manual...
0F0h Clear Math Coprocessor Busy Signal 0F1h Reset Math Coprocessor 1F0h - 1F7h IDE Interface 2F8h - 2FFh Serial Port #2(COM2) 2B0h- 2DFh Graphics adapter Controller 360h - 36Fh Network Ports 3F8h - 3FFh Serial Port #1(COM1) MB980 User’s Manual...
The following table shows the IRQ used by the devices on board. Level Function IRQ0 System Timer Output IRQ1 Keyboard IRQ3 Serial Port #2 IRQ4 Serial Port #1 IRQ8 Real Time Clock IRQ14 Primary IDE IRQ15 Secondary IDE MB980 User’s Manual...