Related Manuals for Sentry NC-GSMDE263
Summary of Contents for Sentry NC-GSMDE263
-
Page 1: Table Of Contents
GSM Intercom Door / Gate Entry System NC-GSMDE263 System Installation, Setting and Operation Manual... -
Page 2: Table Of Contents
User Manual (NC-GSMDE263) Please read this user manual completely before operating this system and keep it in a safe place for future reference. TABLE OF CONTENTS TABLE OF CONTENTS ……………………………………………………………. IMPORTANT SAFETY INSTRUCTIONS………………………………………….. SYSTEM DIAGRAMS Front View ………………………………………………………………………. Back View ………………………………………………………………………. -
Page 3: Important Safety Instructions
Thank you for purchasing the GSM Intercom Door / Gate Entry System. To ensure that you enjoy the full capacity of this product, please read this user manual before proceeding. Be sure to keep this manual for future reference in case any challenge or question should arise. We hope you enjoy your new GSM Intercom Door / Gate Entry System. -
Page 4: Front View
System Diagram (Front View) -
Page 5: Back View
System Diagram (Back View) -
Page 6: Wall Mounting Bracket
System Diagram (Wall Mounting Bracket) -
Page 7: Installation
INSTALLATION GSM Intercom Door / Gate Entry System 1. Take the wall mount bracket from the package and screw it on proper place. (As shown in Step 1 & 2 below) 2. Open the bottom cover of door unit and pass the wires through wire-hole. Then, refer to the “Wiring Diagram and Wiring Instruction”... -
Page 8: Wiring Diagram & Wiring Instructions
Wiring Instructions 1. System Power Supply Wiring The system power supply (adapter) AC 120V or 230V / DC 13V is provided along with the system (please note whether it can meet local voltage specification). The negative wire is connected to Terminal Pin 1 and the positive wire is connected to Terminal Pin 2. -
Page 9: Operation
OPERATION Before operation: Please make sure the GSM Intercom Door / Gate Entry System is installed correctly. Please also study all key functions before use. Power ON/OFF Turn the power ON Insert the plug of the power adapter into the DC power jack of door unit and the other end into an AC power outlet. -
Page 10: Manager Settings
Manager Settings: Under the Manager section, there are 3 main options: “System Setting”, “GSM Setting” and “Door Setting”. System Setting GSM Setting Door Setting Change Manager Password Manager Setting System Setting Change Password Note: The Manager Password is the key to enter Programming Mode. Please make sure to keep the Manager Password in a safe place. -
Page 11: Set Minutes For Talk Time
Set Minutes for Talk Time Manager Setting System Setting Talking Time While at the Manager menu option, press the CALL button Select System Setting and press the CALL button Select Talking Time and press the CALL button Input the number of minutes you’d like the intercom to be able to talk without having to redial, then press the CALL button to save. -
Page 12: Change Speaker Volume
Change Speaker Volume Manager Setting GSM Setting Speaker Volume Note: There are 9 levels of speaker volume level from left (softest) to right (loudest). If the GSM Intercom Door / Gate Entry System is installed in an outdoor environment, please set the speaker level to 5 or 6. Avoid setting the speaker volume to the maximum level as it may cause feedback. -
Page 13: Change Opening Door Password
Change Opening Door Password Manager Setting Door Setting Opening Password Note: This GSM Intercom Door / Gate Entry System system allows the user to open door by pressing the 4 digits Password Code. This feature is for easy access control. We suggest changing the Opening Door Password every month or every two weeks for security reason. -
Page 14: Setup Subscriber Id Number
Subscriber: The Subscriber function of the GSM Intercom Door / Gate Entry System gives the ability to set up multiple tenants and enable the user to press a subscriber number followed the by the CALL button to connect with the tenant. -
Page 15: Contacting A Subscriber
Contacting a Subscriber At the "Welcome!" screen, enter User ID number (from 1 ~ 999999) and then press the CALL button. If the ID exists, the system will start dialing and show “Calling…” on the screen. When the phone is connected, the screen will show “Talking”. -
Page 16: Go Back To "Welcome!" Screen Automatically
Go Back to “Welcome!” Screen Automatically If the manager password has been entered and then no button is pressed within 30 seconds, the screen will go back to the “Welcome!” screen If a Subcriber ID is entered and no button is pressed within 6 seconds, the screen will go back to the ”Welcome!”...