Stanley CS05 User Manual
  1. Manuals
  2. Brands
  3. Stanley Manuals
  4. Chainsaw
  5. CS05
  6. User manual

Stanley CS05 User Manual

Hydraulic chainsaw
Hide thumbs Also See for CS05:
Table of Contents

Advertisement

Quick Links

CS05/06
HYDRAULIC

CHAIN SAW

WARNING
S
, O
M
AFETY
PERATION AND
AINTENANCE
USER'S MANUAL
Stanley Hydraulic Tools
3810 SE Naef Road
Milwaukie OR 97267-5698
© Stanley Hydraulic Tools 2005
503-659-5660
USER USA / CE
FAX 503-652-1780
Printed in U.S.A.
www.stanley-hydraulic-tools.com
66864 9/2006 ver 4

Advertisement

Table of Contents
loading

Related Manuals for Stanley CS05

Summary of Contents for Stanley CS05

  • Page 1: Chain Saw

    HYDRAULIC CHAIN SAW WARNING AFETY PERATION AND AINTENANCE USER’S MANUAL Stanley Hydraulic Tools 3810 SE Naef Road Milwaukie OR 97267-5698 © Stanley Hydraulic Tools 2005 503-659-5660 USER USA / CE FAX 503-652-1780 Printed in U.S.A. www.stanley-hydraulic-tools.com 66864 9/2006 ver 4...

  • Page 3: Table Of Contents

    REPAIRS AND / OR SERVICE TO THIS TOOL MUST ONLY BE DONE BY AN AUTHORIZED AND CERTIFIED DEALER. For the nearest authorized and certifi ed dealer, call Stanley Hydraulic Tools at the number listed on the back of this manual and ask for a Customer Service Representative.

  • Page 4: Certificate Of Conformity

    Data di scadenza Certificate 0466/896/32 1998 AEA Technology Machinery Directive 98/37/EC 1998 AEA Technology Special Provisions: None Spezielle Bestimmungen: Dispositions particulières: Provisiones especiales: Disposizioni speciali: Done at/Ort/Fait à/Dado en/Fatto a Stanley Hydraulic Tools, Milwaukie, Oregon USA Date/Datum/le/Fecha/Data 1998 Signature/Unterschrift/Signature/Firma/Firma____________________________________________________________________________ Position/Position/Fonction/Puesto/Posizione Engineering Manager...

  • Page 5: Safety Symbols

    SAFETY SYMBOLS Safety symbols and signal words, as shown below, are used to emphasize all operator, maintenance and repair actions which, if not strictly followed, could result in a life-threatening situation, bodily injury or damage to equipment. This is the safety alert symbol. It is used to alert you to potential personal injury hazards.

  • Page 6: Safety Precautions

    If so, place the added precautions in the space provided on page 5. The model CS05/06 Hydraulic Chain Saw will provide safe and dependable service if operated in accordance with the instructions given in this manual. Read and under- stand this manual and any stickers and tags attached to the tool and hose before operation.
  • Page 7 • Do not overreach or cut above shoulder height. • Follow the manufacturer’s sharpening and maintenance instructions for the saw chain. • Only use replacement bars and chains specifi ed by Stanley Hydraulic Tools. Chains must meet the requirements of ANSI B175.1 for low kickback performance.

  • Page 8: Electrical Safety Precautions

    ELECTRICAL SAFETY PRECAUTIONS The following guidelines must be followed to prevent accidental contact with overhead electrical conductors and/or com- munication wires and cables. (ref. ANSI Z133.1-2000) Working in Proximity to Electrical Hazards: An inspection shall be made by a qualifi ed arborist to determine whether an electrical hazard exists before climbing, or otherwise entering, or performing work in or on a tree.
  • Page 9 ELECTRICAL SAFETY PRECAUTIONS Table 2 - Minimum approach distances to energized conductors for persons other than qualifi ed line-clearance arborists and qualifi ed line- clearance arborist trainees. Distance Nominal Voltage kV phase-to-phase ft-in 0.0 - 1.0 10-00 3.05 1.1 - 15.0 10-00 3.05 15.1 - 36.0...

  • Page 10: Tool Stickers & Tags

    SERIOUS INJURY. 4. TWO HANDS ARE ALWAYS TO BE USED IN THE OPERATION OF THE CHAIN SAW. 5. USE ONLY STANLEY HYDRAULIC TOOLS REPLACEMENT Stanley Hydraulic Tools BARS AND CHAINS OR THEIR EQUIVALENTS. 6. THIS CHAIN SAW IS EQUIPPED WITH TWO OR MORE KICKBACK 3810 SE Naef Road REDUCING FEATURES.

  • Page 11: Hydraulic Hose Requirements

    HOSE SAFETY TAGS To help ensure your safety, the following DANGER tags are attached to all hose purchased from Stanley Hydrau- lic Tools. DO NOT REMOVE THESE TAGS.

  • Page 12: Htma Requirements

    HTMA REQUIREMENTS TOOL CATEGORY HYDRAULIC SYSTEM REQUIREMENTS TYPE 1 TYPE II TYPE III TYPE RR FLOW RATE 4-6 gpm 7-9 gpm 11-13 gpm 9-10.5 gpm (15-23 lpm) (26-34 lpm) (42-49 lpm) (34-40 lpm) TOOL OPERATING PRESSURE 2000 psi 2000 psi 2000 psi 2000 psi (at the power supply outlet)

  • Page 13: Operation

    fl ow of 4-6 To prevent damage to the retaining ring, do not at- gpm/15-23 lpm at 1500-2000 psi/105-140 bar for the CS05 tempt to force the selector screw counter-clockwise or a fl ow of 7-9 gpm/26-34 lpm at 1000-2000 psi/70-140 bar beyond the point of initial resistance.

  • Page 14: Felling

    OPERATION 6. The saw chain should cut with very little pres sure applied 6. Start the cut horizontally. Pivot the bar in until the cut is to the handle. If you have to force the saw to cut or if the being made parallel to the notch cut.
  • Page 15 OPERATION LOGS WITH PRESSURE ON TOP (FIGURE 2) 1. Observe all safety precautions. 2. Begin with an upper cut, down from the top. Do not cut too deeply. A cut of about 1/3 of the log diameter is enough. 3. Finish with a bottom cut. They should meet. Figure 2.

  • Page 16: Pruning And Debranching

    OPERATION LOGS/LIMBS WITH PRESSURE ON BOTTOM PRUNING AND DEBRANCHING (FIGURE 4) 1. Observe all safety precautions. 1. Observe all safety precautions. 2. Use both hands. Keep a fi rm grip. 2. Begin with a bottom cut. The depth of the cut should be 3.

  • Page 17: Cold Weather Operation

    OPERATION COLD WEATHER OPERATION If the saw is to used during cold weather, preheat the hy- draulic fl uid at low engine speed. When using the normally recommended oils, oil should be at or above 50° F/10° C (400 ssu/ 82 centistokes) before use. Damage to the hydraulic system or saw can result from use with fl...

  • Page 18: Tool Equipment & Care

    fl ow. This can cause damage to internal seals. • Always replace hoses, couplings and other parts with replacement parts recommended by Stanley Hydraulic Tools. Supply hoses must have a minimum working pressure rating of 2500 psi/172 bar.

  • Page 19: Troubleshooting

    Adjust oiler per service instructions. Check power unit for proper fl ow and pressure (4 gpm/15 lpm at 1500 Power unit not functioning. psi/104 bar minimum for the CS05 and 7 gpm/26 lpm at 1000 psi/70 bar for Tool does not run. the CS06).

  • Page 20: Specifications

    SPECIFICATIONS Capacity CS05 ....................... 12 and 15 inch/30 and 38 cm Cut Lengths CS06 ....................12, 15 and 20 inch/30, 38 and 51 cm Cut Lengths Weight (w/o bar) ............................. 6.25 lbs/2.8 kg Length (w/o bar) ............................14 inches/36 cm Width ................................9 inches/23 cm Pressure CS05 .............................1500-2000 psi/105-140 bar...

  • Page 21: Cs05/06 Parts Illustration

    CS05/06 PARTS ILLUSTRATION...

  • Page 22: Cs05/06 Parts List

    CS05/06 PARTS LIST ITEM ITEM PART NO. DESCRIPTION PART NO. DESCRIPTION 00335 BALL BEARING 00753 CAPSCREW 07720 BALL BEARING U/W MODEL 09622 CAPSCREW U/W MODEL 07636 NAME TAG-CS06 04746 AUTOMATIC OILER DECAL 08202 NAME TAG-CS05 04539 WASHER 28323 CE DECAL (CE ONLY)

  • Page 23: Warranty

    fi rst retail purchaser, or for a period of 2 years from the shipping date from Stanley, whichever period expires fi rst, to be free of defects in material and/or workmanship at the time of delivery, and will, at its option, repair or replace any tool or part of a tool, or new part, which is found upon examination by a Stanley authorized service outlet or by Stanley’s factory in Milwaukie, Oregon to be DEFECTIVE IN MATERIAL AND/OR WORKMANSHIP.
  • Page 24 Stanley Hydraulic Tools 3810 SE Naef Road Milwaukie, Oregon 503-659-5660 / Fax 503-652-1780 www.stanley-hydraulic-tools.com...

This manual is also suitable for:

Cs06

Table of Contents