Stanley CS06 User Manual
Hydraulic chain saw
Hide thumbs
Also See for CS06:
- User manual (24 pages) ,
- User manual (24 pages) ,
- Safety, operation and maintenance manual (27 pages)
Related Manuals for Stanley CS06
Summary of Contents for Stanley CS06
- Page 1 CS05/CS06 HYDRAULIC CHAIN SAW USER MANUAL Safety, Operation and Maintenance © 2014 STANLEY Black & Decker, Inc. New Britain, CT 06053 U.S.A. 66864 10/2017 Ver. 13...
-
Page 3: Table Of Contents
REPAIRS AND / OR SERVICE TO THIS TOOL MUST ONLY BE DONE BY AN AUTHORIZED AND CERTIFIED DEALER. For the nearest certified dealer, call STANLEY Infrastructure at (503) 659-5660 and ask for a Customer Service Representative. CS05/CS06 User Manual ◄ 3... -
Page 4: Safety Symbols
Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULATIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and maintenance personnel. 4 ► CS05/CS06 User Manual... -
Page 5: Safety Precautions
The model CS05/CS06 Hydraulic Chain Saw will provide lead. Inhalation of dust containing these or other safe and dependable service if operated in accordance hazardous substances could result in serious with the instructions given in this manual. - Page 6 – Only replacement bars chains the tension on the limb is released. specified by STANLEY. Chains must meet the requirements of ANSI B175.1 for low kickback • Keep the handles dry, clean and free of oil. performance. • Do not operate a chain saw while in a tree, unless •...
-
Page 7: Electrical Precautions
345.0 to 362.0 13–02 4.02 15–00 4.58 16–03 4.96 500.0 to 550.0 19–00 5.80 21–09 6.63 23–06 7.17 765.0 to 800.0 27–04 8.34 31–03 9.53 33–10 10.32 Exceeds phase-to-ground; elevation factor per 29 CFR 1910.269. CS05/CS06 User Manual ◄ 7... - Page 8 Aerial devices and attached equipment (such as chippers) contacting energized electrical conductors shall be considered energized. Contact shall be avoided, except where emergency rescue procedures are being carried out. Emergency rescue should be performed in accordance with 4.3. 8 ► CS05/CS06 User Manual...
-
Page 9: Tool Stickers & Tags
Kickback Warning Decal 101 Sound Level Decal (CE Models Only) 03786 (CE Models Only) GPM Decal – CS06 Model (Not Shown) THIS CHAIN SAW IS D A N G E R D A N G E R EQUIPPED WITH AN AUTOMATIC CHAIN OILER. -
Page 10: Hose Types
HOSE SAFETY TAGS To help ensure your safety, the following DANGER tags are attached to all hose purchased from STANLEY. DO NOT REMOVE THESE TAGS. If the information on a tag is illegible because of wear or damage, replace the tag immediately. A new tag may be obtained from your STANLEY Distributor. -
Page 11: Hose Recommendations
HOSE RECOMMENDATIONS CS05/CS06 User Manual ◄ 11... -
Page 12: Htma / Ehtma Requirements
(103 bar) (103 bar) (103 bar) System relief valve setting 2495 psi 2000 psi 2000 psi 2000 psi 2000 psi (at the power supply outlet) (172 bar) (138 bar) (138 bar) (138 bar) (138 bar) NOTE: 12 ► CS05/CS06 User Manual... -
Page 13: Operation
4-6 gpm/15-23 lpm at 1500-2000 psi/105- beyond the point of initial resistance. 140 bar for the CS05 or a flow of 7-9 gpm/26-34 lpm at 1000-2000 psi/70-140 bar for the CS06. OPERATING PROCEDURES 2. Make certain that the hydraulic power source is... - Page 14 (the felling cut is made higher as the size of the tree increases). Place the saw so the hand guard is close to the tree trunk and the bucking cleat is dug in. 5. Start the cut horizontally. Pivot the bar in until the cut 14 ► CS05/CS06 User Manual...
- Page 15 4. Cut from the bottom. Make a boring cut if the log is close to the ground. 5. Finish with a bottom cut. Figure 4. Crosscutting Logs Larger than Bar Length With Pressure on Top CS05/CS06 User Manual ◄ 15...
- Page 16 3. Pull the saw towards you and cut from the top. 4. Cut from the bottom. Make a boring cut if the log is close to the ground. 5. Finish with a top cut. Figure 6. Crosscutting Thick Logs with Pressure on Bottom 16 ► CS05/CS06 User Manual...
- Page 17 Never force a dull chain to cut. 4. Clean out the bar groove and keep the oil hole open. Turn the bar over to equalize wear on the rails. 5. Always install a new sprocket with a new chain. CS05/CS06 User Manual ◄ 17...
-
Page 18: Tool Protection & Care
This can cause damage to internal seals. • Always replace hoses, couplings and other parts with replacement parts recommended by STANLEY. Supply hoses must have a minimum working pressure rating of 2500 psi/172 bar. 18 ► CS05/CS06 User Manual... -
Page 19: Troubleshooting
Oil leakage between rear gear Motor face seal failure. Replace as required. housing and valve handle assembly. Chain continues to move after valve Chain is too loose. Tighten chain. is shut off. Input flow too high. Decrease flow. CS05/CS06 User Manual ◄ 19... -
Page 20: Specifications
SPECIFICATIONS Capacity CS05 ..................... 12 and 15 inch/30 and 38 cm Cut Lengths CS06 ..................12, 15 and 20 inch/30, 38 and 51 cm Cut Lengths Weight (w/o bar) ...........................6.25 lbs/2.8 kg Length (w/o bar) ..........................14 inches/36 cm Width ..............................9 inches/23 cm Pressure CS05 ..........................1500-2000 psi/105-140 bar... -
Page 21: Cs05/Cs06 Parts Illustration
CS05/CS06 PARTS ILLUSTRATION CS05/CS06 User Manual ◄ 21... -
Page 22: Cs05/Cs06 Parts List
07638 SAW BAR 15 IN. 11207 CIRCUIT TYPE D DECAL (CE ONLY) 07639 SAW BAR 20 IN. 10535 ON/OFF VALVE SPOOL 08348 SAW CHAIN – 12 IN. 07626 O-RING 07641 SAW CHAIN – 15 IN. 22 ► CS05/CS06 User Manual... - Page 23 GPM STICKER (4–6 GPM) 05144 BAR & CHAIN GUARD 00767 GREASE FITTING U/W MODEL ONLY 00936 ADAPTER (COMES WITH ITEM 63) 26414 LOCK OUT KIT, SHIPPED INSTALLED (NOT SHOWN) 03971 COUPLER SET 07830 SEAL KIT CS05/CS06 User Manual ◄ 23...
-
Page 24: Underwater Tools Depth Guideline
UNDERWATER TOOLS DEPTH GUIDELINE UNDERWATER MODELS ONLY Operation Overview Percussive Rotational DO NOT USE HYDRAULIC TOOLS UNDER- Tools: Breakers, Tools: Grinders, WATER THAT ARE NOT DESIGNATED AS Hammer Drills and Saws, Chain Saws AN “UNDERWATER” MODEL, OR THIS Chipping Hammers WILL RESULT IN DAMAGE TO THE TOOL. -
Page 25: Notes
NOTES CS05/06 User Manual ◄ 25... - Page 28 STANLEY Infrastructure 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www.stanleyinfrastructure.com...