Operation - American DJ Gobo Motion LED User Instructions

Gobo Motion LED
Operating Modes: The Gobo Motion LED LED can operate in
three different modes. In each mode you can run the fixture as a
stand alone fixture or in a master/slave confiugration. This next
section will detail the differences in the operating modes.
• Sound Active mode -
The fixture will react to sound, chasing through the built-in programs.
• Show mode -
Choose 1 of 8 show modes to run.
• DMX control mode -
This function will allow you to control each individual fixtures traits
with a standard DMX-512 controller such as the Elation
Designer.
™
Universal DMX Control:
universal DMX-512 controller to control the chases and patterns,
dimmer and strobe. A DMX controller allows you to create unique
programs tailored to your individual needs.
1. The Gobo Motion LED has three DMX Channel modes; 1 channel
mode, 3 Channel mode, and 18 Channel mode. To set the chan-
nel mode see page 9. See pages 15-17 for detailed description of
the DMX traits.
2. To control your fixture in DMX mode, follow the set-up procedures
on pages 5-7 as well as the set-up specifications that are
included with your DMX controller.
3. Use the controller's faders to control the various DMX fixture traits.
4. This will allow you to create your own programs.
5. Follow the instruction on page 9 to set the DMX address.
6. For longer cable runs (more than a 100 feet) use a terminator on
the last fixture.
7. For help operating in DMX mode consult the manual included
with your DMX controller.
Sound Active Mode:
This mode allows either single unit or several
units linked together, to run to the beat of the music.
1. Tap the MENU button until
ENTER.
2.
Tap the UP or DOWN buttons to choose either OFF or ON, and
press ENTER, then press and hold MENU for 3 seconds to con-
American DJ - www.americandj.com - Gobo Motion LED Instruction Manual Page 13
®
This function allows you to use a Elation
"SOUN" is displayed, and press

Operation

Gobo Motion LED
firm. To adjust the sound sensitivity see page 10.
3. The optional UC3 Controller (not included) may be used to con-
trol different functions including blackout. See page 15 for UC3
controls.
Show Mode:
This operating mode can be used in stand alone unit or in a master-
slave configuration.
1. Tap the MENU button until
ENTER.
2.
Tap the UP or DOWN buttons until you find your desired show,
Show and press ENTER then press and hold MENU for 3 seconds to
®
con firm. See page 9 for more info.
3. The optional UC3 Controller (not included) may be used to con-
®
trol different functions including blackout. See page 15 for UC3
controls.
Master-Slave Operation
units together and operate without a controller. The units will be sound
activated. In Master-Slave operation one unit will act as the controlling
unit and the others will react to the controlling units programs. Any unit
can act as a Master or as a Slave.
1. Using approved DMX data cables, daisy chain your units togeth-
er via the XLR connector on the rear of the units. Remember the
Male XLR connector is the input and the Female XLR connector
is the output. The first unit in the chain (master) will use the female
XLR connector only - The last unit in the chain will use the male
XLR connector only. For longer cable runs we suggest a termina-
tor at the last fixture.
For the Master unit
2.
played, and Press ENTER. Set the unit to "MAST" and press ENTER.
3. Next set the Master to your desired operating mode.
4. For the slave units
played, and Press ENTER. Set the slave units to either "SL 1" or
"SL 2".
5. The slave units will now follow the Master unit.
6. The optional UC3 Controller (not included) may be used to con-
trol different functions including blackout. See page 15 for UC3
controls.
American DJ
In this mode you can choose 1 of 8 show modes to run.
"SHND" is displayed, and press
This function will allow you to link up to 16
press the MENU button until "SLND" is dis-
press the MENU button until "SLND" is dis-
- www.americandj.com - Gobo Motion LED Instruction Manual Page 14
®
Operation