Wood dust is a carcinogen and can cause cancer and severe respiratory illnesses. model t10097 Wet grinder safety indicates an imminently hazardous situation which, if not avoided, Will result in death or serious injury. indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
Page 4
Keys r e c o m m e n d e d model t10097 Wet grinder...
ON, allow it to gain full speed and wait for at least 1 minute before standing in front of it. model t10097 Wet grinder 6. lung protection. grinding pro- duces hazardous dust, which may cause long-term respiratory problems if breathed.
We are proud to offer the grizzly model t10097 Wet grinder. this model is part of a growing grizzly family of fine power tools. When used according to the guidelines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of grizzly’s commitment to customer...
MACHINE DATA SHEET Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901 MODEL T10097 WET GRINDER Overall Dimensions: Main Specifications: Motor: Features: model t10097 Wet grinder...
110v operation amperage draw the model t10097 motor draws the follow- ing amps under maximum load: motor draw ... 1.2 amps minimum circuit requirement We recommend connecting your machine to a dedicated and grounded circuit that is rated for the amperage given below. never...
Page 9
3: setup unpacking the model t10097 was carefully packed when it left our warehouse. if you discover any parts are damaged after you have signed for delivery, please immediately call Customer Service at (570) 546-9663 for advice. save the containers and all packing materials for possible inspection by the carrier or its agent.
3 for the minimum working clearances. remember that the model t10097 Wet grinder has no specific front or back side and must be repositioned depending on the desired grinding/sharp- ening/honing action.
Check parallel figure 5. parallel check. test run once your model t10097 is positioned, test run the machine to make sure it runs properly. if, during the test run, you cannot easily locate the source of an unusual noise or...
Wet grinder wheels are designed specifi- cally for slow rotation, there is still the possibility that blades and tools being sharpened on either wheel could be dislodged from your grasp.
Wet grinder is equipped with a universal support that serves as a tool rest and as an attachment point for job-specific accessories. it can be attached in two positions, allowing for grinding with or against the rotation direc- tion of the grinding wheel.
Jig the model t10097 Wet grinder includes a grinding jig for securing a variety of tools during grinding. to use the grinding jig: 1. disConneCt grinder poWer! 2. slide the grinding jig onto the universal support as shown in figure 8.
Page 15
Wet grinder comes with an angle guide to help identify and maintain the cutting angle on a variety of tools. to use the angle guide: 1. locate the eight measuring notches on the angle finder (figure 10).
Water reservoir the model t10097 Wet grinder is designed for wet grinding and should never be used without some kind of fluid. the mounting tabs on the reservoir serve as hooks to attach to the reservoir mount- ing slots (figure 12).
Page 17
Before use, the stropping wheel must be properly prepared. the preparations below will be sufficient for sharpening five to ten tools.
Page 18
Industrial diamond for dressing grinding wheels. 8¼" long round body with knurled grip for maximum control. Includes protec- tive rubber end cap. model h5891 ¼ carat. model h5892 ¾ carat. figure 17. Models H5891 & 5892. model t10097 Wet grinder...
5. install correct fuses or cir- cuit breakers. 1. reduce load on motor. 2. inspect connections on motor for loose or shorted terminals or worn insula- tion. model t10097 Wet grinder...
1. insufficient wheel prepara- loses performance. tions. 2. Wheel is damaged/worn. model t10097 Wet grinder solution 1. dress the grinding wheel. 2. use a holding device to firmly retain the workpiece. 3. dress the grinding wheel.
View this page in color at www.grizzly.com. WARNING! SHOCK HAZARD! Disconnect power before working on wiring. figure 18. switch connections. Wiring diagram JUNCTION BOX (Viewed from behind) 5-15 Plug ⁄ HP MOTOR figure 19. motor connections. model t10097 Wet grinder...
Page 23
STROPPING WHEEL PT10097028 MOTOR SHAFT PRP56M ROLL PIN 4 X 25 PRP23M ROLL PIN 4 X 44 PW06M FLAT WASHER 12MM model t10097 Wet grinder REF PART # DESCRIPTION PT10097032 HOUSING PHTEK18 TAP SCREW #10 X 5/8 G8988 ON/OFF SWITCH...
Page 24
Warning labels breakdown & parts list REF PART # DESCRIPTION PT10097100 MACHINE ID LABEL PT10010101 DIRECTION LABEL REF PART # DESCRIPTION PLABEL-11C READ MANUAL 1.5W X 2.5H PT10097103 RESPIRATOR/GLASSES WARNING model t10097 Wet grinder...
Page 25
____20-29 ____50-59 how long have you been a woodworker/metalworker? ____0-2 years how many of your machines or tools are grizzly? ____0-2 do you think your machine represents a good value? ____yes Would you recommend grizzly industrial to a friend? ____yes Would you allow us to use your name as a reference for our customers in your area? note: We never use names more than 3 times.
Page 26
2069 bellingham, Wa 98227-2069 tape along edges--please do not staple place stamp here...
Page 27
Warranty grizzly industrial, inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. this warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of mainte- nance.