Page 2
This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death.
section 1: safety For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazard- ous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages.
Page 4
safety instructions for power tools (continued) maintain tools With care. alWays use safety glasses. Keep tools lubricated and clean for also use a face or dust mask if cutting best and safest performance. Follow operation is dusty. everyday eyeglasses instructions for lubricating and changing only have impact resistant lenses, they accessories.
additional safety instructions for angle grinders eye protection. grinding causes Wheel flanges. only use the small particles to become airborne at a flanges included with the tool when high rate of speed. alWays wear safety mounting wheels. other flanges may not properly secure the wheel and cause an glasses when using this tool.
For your convenience, we post all available C/o technical documentation Manager manuals and manual updates for free p.o. box 2069 on our website at www.grizzly.com. any bellingham, Wa 98227-2069 updates to your model of tool will be email: manuals@grizzly.com reflected in these documents as soon as they are complete.
section 3: setup unpacking inventory this tool was carefully packaged for safe transportation. remove the packaging materials from around the tool and inspect it. if you discover any damage, please immediately call Customer Service at (570) 546-9663 for advice. save the containers and all packing materials for possible inspection by the carrier or its agent.
Page 9
assembly always consider the position of the wheel guard when installing the adjusting the Wheel guard handle. never operate the grinder the wheel guards can be adjusted with the handle installed toward the for maximum safety during grinding open face of the guard. this could operations.
power connection connecting power 1. turn the tool power switch oFF. polarized plug requirements 2. insert the power cord plug into a match- ing power supply receptacle. the tool is this grinder is equipped with a 16aWg now connected to the power source power cord and typical 1-15 polarized (see figure 7).
test run 4. Make sure you have read and understand the safety instructions at the beginning of the manual and that the grinder is setup properly. once assembly is complete and a grinding wheel is installed (see installing/changing 5. Connect the grinder to power, as shown on page 8.
section 4: operations using the angle grinder read and understand all safety instructions in this manual before starting. always test on a scrap piece of material similar to the workpiece. trial and error is often the best way to determine the ideal setup.
Page 14
zirconia flap discs type 27 grinding Wheels these high density zirconia Flap discs these grinding wheels will make quick are made of overlapping cloth backed work of grinding jobs. the ⁄ " wheels sandpaper segments that are designed work great for notching and light cut-off to wear away, constantly exposing fresh operations, while the 1/4"...
section 6: maintenance regular maintenance these procedures should be done before and after each use: • Check the wheel before each use to ensure no cracks and chips are present, eye inJury hazard! Wear safety goggles with full eye and that wheel size is sufficient to protection from all sides when safely grind.
section 7: service troubleshooting important: tool repairs must be completed by a qualified service person. symptom possible cause solution Motor does not 1. the tool is not getting power. 1. Check power connection. run. 2. Carbon brushes are worn 2. replace both carbon brushes (see page 15).
changing motor 2. With the #2 flat head screwdriver, release the tension on the flat coil brushes spring that holds the carbon brush in place, as shown in figure 17. these grinders use carbon brushes that wear out over time and need replacing. tools needed phillips head screwdriver #2 ....
installing/changing 3. remove the outer flange and old wheel. grinding Wheels 4. install the new wheel. these angle grinders use type 27 grinding 5. replace the outer flange and tighten wheels. refer to specifications on page it while depressing the spindle lock 5 to match the grinder to the proper wheel.
section 8: parts t10494 & t10495 main breakdown Parts breakdown provided for reference only. Not all parts shown are available for purchase. t10493, t10494 & t10495 (Mfg since 10/11)
Page 20
TAP SCREW M4 X 16 PT10493044 HANDLE t10494 & t10495 labels breakdown REF PART # DESCRIPTION REF PART # DESCRIPTION PT10494058 MACHINE ID LABEL (T10494) PT10494059 GRIZZLY LABEL PT10495058 MACHINE ID LABEL (T10495) PT10493053 SAFETY LABEL t10493, t10494 & t10495 (Mfg since 10/11)
Page 21
t10493 main breakdown Parts breakdown provided for reference only. Not all parts shown are available for purchase. t10493, t10494 & t10495 (Mfg since 10/11)
Page 22
PT10493050 O-RING P609ZZ BALL BEARING 609ZZ PT10493051 OIL SEALING PLATE PT10493026 BAFFLE t10493 labels breakdown REF PART # DESCRIPTION REF PART # DESCRIPTION PT10493051 MODEL ID LABEL PT10493053 SAFETY LABEL PT10493052 GRIZZLY LABEL t10493, t10494 & t10495 (Mfg since 10/11)
Warranty Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty and any and all warranties that may be implied by law, including any merchantability or fitness, for any par- ticular purpose, are hereby limited to the duration of this written warranty.
Page 24
Buy Direct and Save with Grizzly – Trusted, Proven and a Great Value! ® ~Since 1983~ Visit Our Website Today For Current Specials! ORDER 24 HOURS A DAY! 1-800-523-4777...