Table of Contents
Advertisement
Advertisement
Table of Contents
Troubleshooting
Related Manuals for Jacuzzi Aero Select
Summary of Contents for Jacuzzi Aero Select
- Page 1 Select Series Spas Owner's Manual WHIRLPOOL BATH...
-
Page 2: Important Safety Information
IMPORTANT SAFETY INFORMATION READ AND FOLLOW ALL INSTRUCTIONS Warning — Risk of injury: Children, the elderly, and the DANGER — RISK OF ELECTRICAL SHOCK: When install- infirm should not use the spa unless they are supervised at all ing and operating this electrical equipment, basic safety pre- times. -
Page 3: Table Of Contents
Select Whirlpool Spas OWNER’S MANUAL Contents Specifications __________________________________________________________ 2-4 Installation Inspection and Shipping Claim ______________________________________________ 5 Positioning Your Spa ______________________________________________________ 5 Electrical Requirements ___________________________________________________ 5 Electrical Precautions _____________________________________________________ 6 Outdoor Installation _______________________________________________________ 6 Drainage _______________________________________________________________ 6 Indoor Installation ________________________________________________________ 6 Equipment Set-Up ________________________________________________________ 7 Selct Spa (Aero, Laser, Santina &... -
Page 4: Specifications
SELECT SERIES SPECIFICATIONS Aero ™ Select DIMENSIONS 84" (2134 mm) L 76" (1980 mm) W 30" ( 762 mm) H ELECTRICAL REQUIREMENTS 76" 230 VAC, 4-Wire 50 AMP, 60 Hz GFCI Protected Requires Dedicated Separate Circuit TOTAL WEIGHT/ FLOOR LOADING 3299 lb (1450 kg) ACCESS 74 lb/sq. - Page 5 SELECT SERIES SPECIFICATIONS ™ Laser Select 84" 15" TYP. DIMENSIONS 15" 84" (2134 mm) L TYP. 84" (2134 mm) W 36" ( 914 mm) H ELECTRICAL REQUIREMENTS 230 VAC, 4-Wire, 84" 50 AMP, 60 Hz GFCI Protected Dedicated Separate Circuit TOTAL WEIGHT/ FLOOR LOADING 4738 lb (2154 kg)
- Page 6 SELECT SERIES SPECIFICATIONS ™ Solaris Select 18" DIMENSIONS 78" 78" (1981 mm) L 72" (1829 mm) W 32" ( 813 mm) H ELECTRICAL REQUIREMENTS 230 VAC, 4-Wire, 72" 50 AMP, 60 Hz 72" GFCI Protected Dedicated Separate Circuit TOTAL WEIGHT/ FLOOR LOADING 3102 lb (1410 kg) 80 lb/sq.
-
Page 7: Installation
Check for shipping damage upon receipt of the spa. Because your spa is portable, you can locate it just Jacuzzi Whirlpool Bath is not responsible for damage to about anywhere you wish—on a deck, patio, or even the spa sustained during shipment. If damage is evident indoors. -
Page 8: Electrical Precautions
5 feet of the spa when the spa is help maintain comfort and minimize moisture damage to being used. the building. Jacuzzi Whirlpool Bath is not responsible for damages resulting from excess moisture or water All fixed metal objects located within 5 feet of the spillage. -
Page 9: Equipment Set-Up
Instructions. Test for water quality and then add treatment chemicals as necessary to ensure proper water quality levels. All Jacuzzi Whirlpool Bath spas are factory tested for proper operation and water tight connections prior to shipment. If leaks or other malfunctions are detected,... -
Page 10: Selct Spa (Aero, Laser, Santina & Solaris) 50-30 Amp Conversion
INSTALLATION For Aero Select, Laser Select, Santina Select and Solaris Select: Electrical Conversion from 50 AMP to 30 AMP Operation Your spa, as it comes from the factory, requires a 230 VAC, 50 AMP, 4-wire, grounded type GFCI (Ground Fault Circuit Interrupter) protected electrical service. -
Page 11: Alexa Electrical Conversion (115V-230V)
INSTALLATION Alexa Electrical Conversion The Alexa spa, may be converted from the factory supplied 115 VAC, 20 AMP to operate on a 230 VAC, 50 AMP circuit. This must be a protected electrical service with copper conductors, a 4-wire grounded type GFCI protected circuit and have no other appliances on the circuit. -
Page 12: Ozone Generator Installation (Aero, Laser, Santina & Solaris)
INSTALLATION For Aero Select, Laser Select, Santina Select and Solaris Select: Ozone Generator Installation Instructions Your "ozone-ready" spa is designed for easy field conversion to an ozone generator system. You will need: A. H319000 Complete Ozone Conversion Kit B. H318000 Plumbing Kit plus an ozone generator of your choice. - Page 13 INSTALLATION Install the ozone generator according to the manufacturer's instructions. Attach the 4-1/2" x 14" x 1/2" thick plywood board to the spa, just above the electrical cabinet, using the #6 screws provided. Several commer- cially available ozone generators will fit easily in this location. Attach the ozone generator to the board using the #10 screws provided.
-
Page 14: Operation
Besides being a beautiful addition to your indoor decor protected with a Ground Fault Circuit Interrupter (GFCI) or outdoor landscaping, your Jacuzzi Whirlpool Bath spa (refer to Electrical Requirements). At initial start-up and will provide you with the ultimate in spa pleasure. -
Page 15: Select Series Control Panel
OPERATION Control Panel The spa will automatically begin to operate when electrical power is applied. There is no ON/OFF switch for the spa system. The control system has been designed so that by connecting the spa to its properly grounded power source, the spa's set temperature is preset to 100 F. - Page 16 OPERATION Automatic Filter Cycles Your spa will automatically filter itself for 2 hours twice each day. The first filter cycle will begin 1 minute after the spa is energized. The second filter cycle will begin twelve hours after the start of the first cycle. The low-speed jets will constantly run during the filter times (unless the high-speed jets are on) and the heater will be enabled.
-
Page 17: Alexa Control Panel
OPERATION Alexa Control Panel The spa will automatically begin to operate when electrical power is applied. There is no ON/OFF switch for the spa system. The control system has been designed so that by connecting the spa to its properly grounded power source, it will begin to operate. -
Page 18: Normal Operation/Whirlpoolsystem
OPERATION Normal Operation/WhirlpoolSystem You can enjoy the spa with or without activating the whirlpool. Either way, bathing in your spa can be pleasurable, as well as therapeutic. After a busy, stressful day, you can look forward to soaking in your spa in still water with no turbulence—only the gentle warmth of the soothing and relaxing water. -
Page 19: Maintenance
(K521000) should be replaced after four months of filter pump operation. These are available through your Jacuzzi Whirlpool Bath dealer. Do not use products containing bromine, sodium bromide or biguanides if the spa water treatment cartridge is used. -
Page 20: Disinfecting
MAINTENANCE Water Chemistry (Continued) Disinfecting Balancing pH When filling the spa for the first time, follow the For good hygiene and equipment longevity, main- purge/sanitizing instructions in the Equipment Set-Up tain the pH of your spa water according to the instruc- procedure of the Installation Instructions. -
Page 21: Water Level/Drain
It is a safety device and (available from your Jacuzzi Whirlpool Bath dealer or must be in place over the suction fitting to minimize most pool supply stores). Follow the manufacturer’s potential hazard of hair and body entrapment. -
Page 22: Factory Installed Wood Skirt
MAINTENANCE Factory Installed Wood Skirt Winterizing In a climate where winter temperatures are below Your spa is supplied with a factory-installed wood freezing, follow this procedure when the spa will skirt which completely surrounds the spa. The skirt can NOT be used: be opened for service. -
Page 23: Spa Light
An optional spa cover for your spa is available from each spa light. To change the filter, simply snap the your Jacuzzi Whirlpool Bath dealer. Use of this cover will colored filters in place on top of the normal lens. Two help to reduce energy costs by minimizing heat loss and replacement bulbs are also included. -
Page 24: Troubleshooting Guide
E. GFCI tripped. E. Reset GFCI. F. Faulty pump or motor. F. * *NOTE: The skills and tools necessary for the safe repair of this spa require the services of qualified service personnel. Contact your Jacuzzi Whirlpool Bath dealer. -
Page 25: Troubleshooting Guide
10. Low water flow from six-jet A. Cycle valve strainer clogged. page x.) wave seat. (Quantum only) *NOTE: The skills and tools necessary for the safe repair of this spa require the services of qualified service personnel. Contact your Jacuzzi Whirlpool Bath dealer. -
Page 26: Alternate Use Of Water Rainbow
USE INSTALLATION INSTRUCTIONS SUPPLIED WITH PRODUCT. Jacuzzi Whirlpool Bath has obtained applicable code (standards) listings generally available on a national basis for products of this type. It is the responsibility of the installer/owner to determine specific local code compliance prior to installation of this product. Jacuzzi Whirlpool Bath makes no representation or warranty regarding, and will not be responsible for any code compliance. -
Page 27: Warranty
WARRANTY COVERAGE Jacuzzi Whirlpool Bath (the “Company”) offers the following express limited warranty to the original purchaser of any Jacuzzi Whirlpool Bath Select Spa Line Product (“unit”) who purchases the product for personal or single family use (“user”). The Company will repair or replace, at its option, the unit or its equipment in accordance with the following terms and conditions. - Page 28 The Company will provide the warranty service described above when the following conditions have been met: the failure is of the nature or type covered by the warranty; the user has informed an Authorized Jacuzzi Whirlpool Bath Dealer or Warranty Service Department Representative of the nature of the problem during the warranty period;...