Advertisement
Quick Links
Download this manual
See also:
Owner's Manual
Please note that some of the contact details on
this PDF document may not be current.
Please use the following details if you need to
Email: customer.services@gdcgroup.co.uk
The Help Centre section of this website also features a wide range
of information which may be of use to you and is available 24
hours a day. It includes:
• Operating and installation instructions downloads
• Request a repair
• Where to buy our products
• Literature downloads
• Heating requirement calculator
A division of GDC Group Ltd
Millbrook House Grange Drive Hedge End Southampton SO30 2DF
www.credaheating.co.uk
Contact Details
contact us:
Telephone: 0844 879 3588
www.credaheating.co.uk/help‐centre
Registered No: 1313016 England
VAT GB 287 1315 50004
EEE Producer Registration Number –
WEE/GE0057TS
Paper from sustainable sources
Advertisement
Related Manuals for Creda NewEra 79348S
Summary of Contents for Creda NewEra 79348S
- Page 1 Contact Details Please note that some of the contact details on this PDF document may not be current. Please use the following details if you need to contact us: Telephone: 0844 879 3588 Email: customer.services@gdcgroup.co.uk The Help Centre section of this website also features a wide range of information which may be of use to you and is available 24 hours a day. It includes: • Operating and installation instructions downloads • Request a repair • Where to buy our products • Literature downloads • Heating requirement calculator www.credaheating.co.uk/help‐centre A division of GDC Group Ltd Registered No: 1313016 England VAT GB 287 1315 50004 Millbrook House Grange Drive Hedge End Southampton SO30 2DF EEE Producer Registration Number –...
-
Page 2: Assembly Instruction
TSR Supaslim Combi Combined Storage and Fan Heater Assembly Instruction Manual Automatic Model Nos: 79348S 75772001S Cat. Nos: TSR12CW TSR12ACW This product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic Compatibility (EMC) EN55014, EN60555-2 and EN60555-3. - Page 3 IMPORTANT NOTES: It is important to read these instructions carefully and also note the information given on the heater itself. As these particular instructions refer to the assembly and installation of a new heater, they should be retained by the installer; not left behind for the user as this would invite the dismantling and servicing by unqualified persons.
- Page 4 PLEASE DON’T TAKE CHANCES Site conditions may vary considerably and Creda cannot recommend the correct wall fixings to be used. It is the responsibility of the installer to ensure that adequate permanent fixing has been achieved. Purely for guidance the suggested fixings are made for certain wall materials but this list is not comprehensive or authoritative.
- Page 5 First, turn carton upside down Open bottom flaps on cartonThe corner fitments contain the fixing kit. Stand the heater against the wall in its intended position. Mark the position of the two outside corners of the wall bracket. Carefully place the heater aside, and remove the wall bracket from the heater by removing the screw at each end.
- Page 6 WALL FIXINGS - VERY IMPORTANT When bracket is securely fixed, replace You must fit a the heater under the bracket angle and retaining screw at align screw holes on heaters ends. each end of the There are two fixing slots at each end of heater, heater.
-
Page 7: Circuit Diagram
If mains connection is to be made from the left hand side, at this point the mains lead must be secured to the base of the fan box by fixing the 79348S ties provided in the fixing kit through the holes along the 75772001S rear of the fan box base. - Page 8 WARNING Remove the inner front panel; this carries on it’s inner face the front insulation slab. Handle this with care, the insulation must not be damaged. REMOVE ALL THE PACKING CARDBOARD FROM INSIDE THE STORAGE BRICK COMPARTMENT, IF LEFT INSIDE IT WILL BE SET ON FIRE WHEN THE HEATER IS SWITCHED ON.
-
Page 9: Setting The Controls
Check that the front insulation slab is properly attached to the inner front panel and refit panel (insulation innermost) to the heater by locating its bottom edge behind the front lip of the chassis, and inserting retaining screws along the top and both sides. With the bricks pushed well back, as mentioned earlier, and the insulation properly aligned, there should be no bulging of this panel and no undue force necessary to fix it.