Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Online Manual
AOpen reserves the right to revise all the
specifications and information contained
in this documentation, which are subject
to change without notice.
AUX-IN Connector
S/PDIF Connector
Front Audio Connector
CD-IN Connector
CNR Expansion Slot
32-bit PCI Expansion Slot x3
AGP 8X Expansion Slot
USB2.0 Connector
IEEE 1394 Connector x2
(for MK77M-1394)
JP14 CMOS Data Clear Jumper
Case Open Connector
Front Panel Connector
SPP/EPP/ECP
PS/2 Mouse
Parallel Port
Connector
PS/2 Keyboard
USB2.0
COM 1 Port
Ports
Connector
RJ45 LAN Jack
Line-In
Speaker
Out
MIC-In
VGA Port
USB2.0 Ports
Resetable Fuse
JP28 Keyboard/Mouse Wakeup Jumper
ATX Power Connector
2200μF Low ESR Capacitors
SYSFAN3 Connector
462-pin CPU Socket with Voltage and
Frequency Auto-Detection that supports
TM
TM
TM
AMD
Athlon
/ and Athlon
XP (with
CPU
Overheat
Protection
circuit
TM
Athlon
XP CPU only)
®
VIA
KM400 and VT8237 Chipsets
184-pin DIMMx2 supports DDR333/266 max.
to 2GB
CPUFAN1 Connector
IDE Connector x2 (ATA/66/100/133 supported)
IrDA Connector
JP21 K7 Host Clock Select Jumper
FDD Connector
SYSFAN2 Connector
to
Advertisement
Table of Contents
Related Manuals for AOpen MK77M-8XN
Summary of Contents for AOpen MK77M-8XN
- Page 1 SPP/EPP/ECP RJ45 LAN Jack PS/2 Mouse Parallel Port Line-In Connector AOpen reserves the right to revise all the Speaker specifications and information contained in this documentation, which are subject to change without notice. MIC-In PS/2 Keyboard USB2.0 COM 1 Port VGA Port USB2.0 Ports...
-
Page 2: Jp14 Clear Cmos
1. JP14 Clear CMOS You can clear CMOS to restore system default setting. To clear the CMOS, follow the procedure below. 1. Turn off the system and unplug the AC power. 2. Remove ATX power cable from connector PWR2. Everything you need to boot this motherboard is included in this 3. -
Page 3: Jp21 K7 Host Clock Selection
Tip: If your system hangs or fails to boot when overclocking, please use <Home> key JP21 K7 Host Clock to restore the default setting or wait AOpen “Watch Dog ABS” for resetting the system Select Jumper in few seconds and the system will auto-detect hardware again. -
Page 4: Connecting Front Panel Cable
6. Connecting IDE and Floppy 8. JP28 KB/Mouse Wakeup Jumper Connect 34-pin floppy cable and 40-pin IDE cable to floppy connector FDC connector. Be This motherboard provides keyboard / mouse wake-up function. You can use JP28 to careful of the pin1 orientation. Wrong orientation may cause system damage. enable or disable this function, which could resume your system from suspend mode with keyboard or mouse installed. - Page 5 10. Support Eight USB 2.0 Ports 12. S/PDIF Connector This motherboard provides eight USB ports to connect USB devices such as mouse, S/PDIF (Sony/Philips Digital Interface) is a newest audio transfer file format, which provides impressive audio quality through optical fiber and allows you to enjoy digital audio instead of analog audio. Through a keyboard, modem, printer, etc.
-
Page 6: Bios Upgrade Under Windows Environment
BIOS Setup, press <Del> during POST (Power On Self Test). upgrading. Choose "Load Setup Defaults" for recommended optimal performance. Download the new version of BIOS package zip file from AOpen official web site. (ex: http://english.aopen.com.tw/) Unzip the download BIOS package (ex: WMK77M8XN102.ZIP) with WinZip (http://www.winzip.com) in Windows environment. -
Page 7: Part Number And Serial Number
IDE cable. The problem should be caused by the Check if the system can IDE cables or HDD itself. reboot successfully. Re-install Windows 95, Windows 98 or Windows NT. MK77M-8XN is model name of motherboard; R1.02 is BIOS version... - Page 8 Online Manual: To download manual, please log on and then select your preferred language. Under “Type” directory, choose “Manuals” to go to our manual database. You can also find the manual and EIG in AOpen Bonus Pack. http://download.aopen.com.tw/downloads Dear Customer, Thanks for choosing AOpen products.