TABLE OF CONTENTS Instruction manual is for: • ComfortSport 5-Point Newborn/Toddler Car Seat • ComfortSport Overhead Shield Newborn/Toddler Car Seat Instructions for these models are the same unless otherwise noted. ❃ Before You Begin Important Information... Warnings... Basic Information... What is LATCH?...
For recall information: • Call the U.S Government’s Auto Safety Hotline at 1-800-424-9393 (202-366-0123 in D.C. area) • www.nhtsa.dot.gov • Call Graco Children’s Products Inc. at 1-888-224-6549 www.gracobaby.com ❃ Safety First Check List ✔ Read and understand instruction manual and car seat labels.
WARNINGS Failure to follow these instructions and car seat labels can result in child striking the vehicle’s interior during a sudden stop or crash. Secure car seat with a vehicle seat belt or that is properly routed as shown in this manual.
Page 5
DO NOT use car seat if it is damaged or missing parts. DO NOT use accessories or parts other than those provided by Graco. Their use could alter the performance of the car seat. Rear-facing car seat must be properly leveled: •...
❃ LATCH or a Car seat parts can get very hot in the sun or warm weather. To avoid burns, always check before putting child in car seat. Do not use this car...
Some vehicle owner manuals use the term ISOFIX to identify the new car seat anchorage system. This carseat with LATCH can also be used in vehicle seating positions equipped with ISOFIX.
LATCH consists of a permanently attached lower anchorage belt and a top tether strap (Fig. a). ONLY use LATCH in a seating position recommended by vehicle manufacturer. Car Seat Vehicle Top Tether Top Tether Anchor Point Vehicle Lower Anchor Points (Fig.
According to the American Academy of Pediatrics, these infants may suffer breathing difficulties if improperly reclined in a car seat. Graco advises that you have your physician or hospital staff evaluate your infant and recommend the proper car seat or car bed before you and your infant leave the hospital.
Hook connectors to vehicle lower anchors (fig. a). Pull connectors to be sure they are securely attached to the anchor points. (fig. b). Press down firmly in center of car seat while pulling LATCH adjustment belt. (fig. c).
Page 11
REAR-FACING INSTALLATION WITH LATCH (continued): Tether Openings Towels LATCH (fig. a) (fig. e) (fig. b) (fig. c) (fig. d)
(see page 23, fig. k). Belt must lay flat and not be twisted. Adjust car seat to upright position (see pages 18 and 19, fig. b) and place vehicle seat equipped with For ease of installation, extend to its maximum length.
Page 13
FORWARD-FACING INSTALLATION WITH LATCH (continued): Tether Openings Pull to tighten LATCH (fig. a) (fig. e) (fig. c) (fig. b) (fig. d)
(fig. a). • Adjust LATCH belt to remove excess slack by pulling adjustment belt. Adjust car seat to recline position (see page 18 and 19, fig. b) and place seat. Thread vehicle seat belt through openings and buckle belt.
Page 15
REAR-FACING INSTALLATION WITH VEHICLE SEAT BELTS (continued): Tether Storage Openings LATCH Towels (fig. d) (fig. a) (fig. b) (fig. c)
Page 16
Lift seat pad flap (available on some models). Thread vehicle seat belt through openings. Buckle belt (fig. b). Press down firmly in center of car seat to compress vehicle seat cushion while tightening vehicle seat belt. Use your knee to press down in center of car seat (fig.
FORWARD-FACING INSTALLATION WITH VEHICLE SEAT BELTS (continued): Tether Storage Openings Pull to tighten LATCH Stand (fig. a) (fig. e) (fig. b) (fig. c) (fig. d)
• Harness tongue must be in opening closest to but not under child. 5-Point Models Only: Place child in car seat with child’s back flat against back of car seat. Place harness straps over child’s shoulders and insert tongue(s) into buckle.
Page 19
PLACING CHILD IN CAR SEAT (continued) (fig. a) (fig. b)
• From bottom of car seat, pull crotch strap clip out and remove clip from crotch strap loop. • From top of car seat, pull crotch strap out and thread through desired slot. Make sure red button is facing away from child.
Page 21
OPERATIONS and ADJUSTMENTS Lift (to release) Pull Belt (to tighten) (fig. a) Upright Recline (fig. b) (fig. c) (continued) Clip (fig. d)
Lift and hold metal release bar. Pull harness straps out. B Remove both shoulder harness strap loops from Splitter Plate on back of car seat. C Change harness strap slots. Make sure harness straps are threaded through matching slot of seat pad and car seat.
Page 23
OPERATIONS and ADJUSTMENTS (continued) Loop Loop Splitter Plate Bottom Loop (fig. f) (fig. e) Stand (fig. g)
(fig. j and fig. k). Belts must remain flat and not twisted. C Re-attach pad to car seat by pressing 2-button clips back in place. (continued) Rotating LATCH Belt (under seat pad) (fig.
Page 25
OPERATIONS and ADJUSTMENTS Route LATCH belt through Rear-facing openings for: • LATCH Rear-facing use. • LATCH storage with Forward-facing vehicle seat belt use. Pg. 25. Rear-facing (fig. j) (continued) Route LATCH belt through Forward-facing openings for: • LATCH Forward-facing • LATCH storage with Rear-facing...
LATCH from Vehicle Anchor Points: A Tilt metal tab of adjuster to release tension (fig. l). Press down on car seat compressing vehicle seat cushion to reduce tension on lower anchorage belt. B Press and hold LATCH (lower hinge) (fig. m).
OPERATIONS and ADJUSTMENTS LATCH storage: • Locate LATCH storage bars under seat pad on sides of car seat (fig. o). • Fasten LATCH onto storage bar as shown. (fig. p) Repeat for other side of seat. (continued) LATCH storage bar (fig.
VEHICLE SEAT BELTS WARNING Not all vehicle seat belts can be used with a car seat. The car seat must be held securely at all times by a lap belt (or lap belt portion of a lap/shoulder belt) that will not change length while driving.
Page 29
Check vehicle owner’s manual or see vehicle dealer for car seat installation requirements. • If approved for use with car seat, install car seat and check for secure installation by pulling car seat front to back. If car seat slides forward, DO NOT use these seat belts.
Page 30
Lap Belts - Manually Adjustable The locking latch plate on some seat belts may slip and loosen after being buckled on car seat if positioned at a certain angle. If this happens, flip latch plate over (fig. a) and re-buckle. Test installation again to see if this works.
Page 31
Passive Restraint - Lap Belt with Motorized Shoulder Belt DO NOT use with any car seat. ❃ Passive Restraint Lap or Shoulder Belt Mounted on Door DO NOT use with any car seat. Belts will not stay tight while driving.
Page 32
Belt with Locking Latch Plate The locking latch plate on some seat belts may slip and loosen after being buckled on car seat if positioned at a certain angle. If this happens, flip the latch plate over (fig. b) and re-buckle.
• Buckle vehicle seat belt. Press car seat further down into vehicle seat cushion to help buckle vehicle seat belt. Test installation to see if car seat is secure. If not secure, repeat above step until secure. (fig. a) 1/2 inch (1 cm)
❃ Tether Storage DO NOT anchor tether strap to the vehicle when using car seat rear-facing. Tether hook must be attached to car seat for rear-facing use or if vehicle is not equipped with tether anchors. For storage of tether hook: •...
❃ Cup Holder Available on some models: • Locate slot in armrest UNDER armrest pad on either side of car seat. • Push cupholder down over side of seat and snap cupholder into slot to secure. Removing Cup Holder: • Feel bottom of cupholder and locate tab on bottom edge.
Page 36
Unhook “J” hooks from car seat shell. Pull three 2-button clips out of lower front edge of car seat shell and inside center of car seat shell. Removing Overhead Shield Pad: Pull both 2-button clips out of shield and unwrap pad from around shield.
(see label on car seat). Contact airline about their policy. Use this car seat only on forward-facing aircraft seats. Install car seat on an aircraft the same way it is installed in a vehicle when using a vehicle seat belt. ❃...
Page 38
PARTS LIST How to Order: Complete the form on the following page. Your car seat model and serial numbers MUST be included on the form to ensure proper replacement parts. Your model number can be found on a sticker on the underside of your car seat. Payment must accompany your order.
Page 39
(Both Numbers Required) SHIP TO: Name Address City, State, Zip Code Telephone (including Area Code) E-mail address Check or money order enclosed (payable to Graco Children’s Products Inc.) Charge to credit card Visa MasterCard Account # Expiration date Signature Serial No.
U.S. or Canada or fax at 1-610-286-4555. or write us at: Graco Children’s Products P.O.Box 100 Elverson, PA 19520-9974 Attention: Customer Service Department Store locking clip here. Graco Children’s Products Inc. A Division of Newell Rubbermaid P.O. Box 100 Elverson, PA 19520...
Page 41
Manual de instrucciones Evite lesiones o la muerte - ¡Lea detenidamente este manual! ISPC001BA 7-02...
Page 42
TABLA DE CONTENIDO Este manual de instrucciones está indicado para el uso del: • Asiento de seguridad ComfortSport de 5 puntos • para recién nacidos / niños de corta edad • Asiento de seguridad ComfortSport con barra • protectora para recién nacidos / niños de corta edad Las instrucciones para estos modelos son las mismas a menos que se indique lo contrario.
Gobierno de EE.UU. al 1-800-424-9393 (202-366-0123 en la zona de Washington D.C) • www.nhtsa.dot.gov • Llame a Graco Children’s Products Inc. al 1-888-224-6549 www.gracobaby.com ❃ Lista de control de seguridad ✔ Lea detenidamente este manual de instrucciones y las etiquetas del asiento de seguridad.
ADVERTENCIA El incumplimiento de estas instrucciones y de las indicaciones de las etiquetas del asiento podría causar el choque del niño contra el interior del vehículo durante una parada repentina o un accidente. Sujete el asiento con un cinturón de seguridad del vehículo o un sistema LATCH que esté...
Page 45
Graco, ya que ello podría alterar el rendimiento del asiento de seguridad. Introduzca las correas de arnés en las ranuras adecuadas para su niño.
INFORMACIÓN BÁSICA ADVERTENCIA coloque el asiento orientación trasera para niños en el asiento del vehículo equipado con la bolsa de aire. ❃ Certificación Este asiento de seguridad cumple o excede todos los requisitos requeridos por la Norma Federal 213 de Seguridad de Automóviles para uso en automóviles y aeronaves.
¿QUÉ ES EL LATCH? Las Normas Federales para Seguridad de Automóviles de Estados Unidos han determinado un nuevo sistema de instalación de asientos de seguridad en los vehículos. Este sistema se denomina LATCH, que son las siglas en inglés de: Anclaje inferior y superior para niños Sistema LATCH...
SISTEMA LATCH El sistema LATCH: LATCH consta de un cinturón Anclaje de anclaje inferior permanente y superior del una correa de anclaje asiento de superior (Fig. a). seguridad Punto de anclaje superior del Utilice con LATCH ÚNICAMENTE vehículo en el asiento recomendado por el fabricante del vehículo.
Unidos), estos niños podrían sufrir dificultades de respiración si son recostados de forma incorrecta en un asiento de seguridad. Graco aconseja que pida a su médico o al personal del hospital que examinen a su niño y que le recomienden un asiento o cama para auto adecuado antes de que usted y su niño...
INSTALACIÓN ORIENTADA HACIA ATRÁS El cinturón LATCH debe pasar por la apertura del asiento de seguridad destinada al modo de orientación trasera. (vea la página 23, fig. j). El cinturón debe mantenerse en posición plana sin torcerse. Coloque el asiento de seguridad en posición reclinada (vea las páginas 18 y 19, fig.
Page 51
INSTALACIÓN ORIENTADA HACIA ATRÁS LATCH Anclaje Aperturas Toallas LATCH (fig. a) (fig. e) (fig. b) (fig. c) (fig. d)
INSTALACIÓN ORIENTADA HACIA DELANTE El cinturón LATCH debe pasar por la apertura del asiento de seguridad destinada al modo de orientación delantera (vea la página 23, fig. k). El cinturón debe quedar plano y no torcido. Ajuste el asiento de seguridad a la posición vertical (vea las páginas 18 y 19, fig.
Page 53
INSTALACIÓN ORIENTADA HACIA DELANTE LATCH Anclaje Aperturas Jale para apretar LATCH (fig. a) (fig. e) (fig. c) (fig. b) (fig. d)
INSTALACIÓN DE ORIENTACION TRASERA LOS CINTURONES DE SEGURIDAD DEL VEHÍCULO ADVERTENCIA El cinturón LATCH DEBE almacenarse cuando se utilice el cinturón de seguridad del vehículo para instalar el asiento de seguridad. Almacene el cinturón LATCH conectores por las aperturas para la orientación hacia delante (vea la página 23, fig.
Page 55
INSTALACIÓN DE ORIENTACION TRASERA LOS CINTURONES DE SEGURIDAD DEL VEHÍCULO Barra de almacenaje Aperturas Toallas (fig. a) LATCH (fig. b) Anclaje (fig. d) (fig. c)
INSTALACIÓN ORIENTADA HACIA DELANTE LOS CINTURONES DE SEGURIDAD DEL VEHÍCULO ADVERTENCIA El cinturón LATCH DEBE almacenarse cuando se use el cinturón de seguridad del vehículo para instalar el asiento de seguridad. Almacene el cinturón LATCH conectores a través de las aperturas destinadas a la orientación trasera (vea la página 23, fig.
Page 57
INSTALACIÓN ORIENTADA HACIA DELANTE LOS CINTURONES DE SEGURIDAD DEL VEHÍCULO Anclaje Barra de almacenaje Aperturas Jale para apretar LATCH (fig. a) (fig. e) Soporte (fig. b) (fig. c) (fig. d)
• No ponga almohadillas, mantas ni cojines debajo de las correas o del niño, a menos que sean proporcionados por Graco. • El niño debe llevar ropa que no estorbe al abrochar el arnés. Compruebe el sistema del arnés: •...
Page 59
COLOCAR AL NIÑO EN EL ASIENTO DE SEGURIDAD (fig. a) (fig. b)
OPERACIONES Y AJUSTES Correas del arnés (fig. a): • Para apretar: Jale la lengüeta del cinturón. • Para soltar: Levante la barra de metal • y sosténgala al tiempo que jala las correas • de los hombros. Cierre del arnés: •...
Page 61
OPERACIONES Y AJUSTES Levante (para soltar) Jale el cinturón (para apretar) (fig. a) Vertical Reclinada (fig. b) (fig. c) Clip (fig. d)
Page 62
OPERACIONES Y AJUSTES Cambiar las ranuras de las correas del arnés: A Suelte las correas del arnés: Levante la barra de metal y sujétela. Saque las correas del arnés. B Quite ambos bucles de las correas de los hombros de la placa de unión de la parte trasera del asiento.
Page 63
OPERACIONES Y AJUSTES Bucle superior Bucle Bucle inferior Placa de unión (fig. f) (fig. e) Soporte (fig. g)
OPERACIONES Y AJUSTES Colocación del cinturón LATCH: El cinturón LATCH DEBE aperturas adecuadas según la orientación del asiento. A Quite la almohadilla de la parte delantera del asiento, sacando los clips de dos botones en el borde delantero inferior del asiento (fig.
Page 65
OPERACIONES Y AJUSTES Pase el cinturón LATCH por las aperturas de orientación hacia atrás para: • usar el sistema LATCH orientado hacia atrás. • Almacenaje LATCH con el uso del cinturón de seguridad del vehículo orientado hacia delante. Pág. 25. Orientado hacia atrás (fig.
OPERACIONES Y AJUSTES Retirar el LATCH de los puntos de anclaje del vehículo: A Incline la lengüeta metálica del dispositivo de ajuste para soltar la tensión (fig. l). Oprima el asiento, comprimiendo el cojín del asiento del vehículo para reducir la tensión del cinturón de anclaje inferior.
OPERACIONES Y AJUSTES Almacenaje LATCH: • Ubique las barras de almacenaje debajo la almohadilla del asiento en el lado del asiento de seguridad infantil (fig. o). • Abroche el sistema LATCH almacenaje como se indica. (fig. p) Repita para el otro lado del asiento. LATCH en la barra de Barra de...
CINTURONES DE SEGURIDAD DEL VEHÍCULO ADVERTENCIA No se pueden usar todos los cinturones de seguridad de vehículos con los asientos de seguridad Durante el manejo, sujete siempre el asiento con el cinturón de seguridad de regazo o con una parte del cinturón de regazo/hombro que no cambie de longitud.
Page 69
CINTURONES DE SEGURIDAD DEL VEHÍCULO ❃ Cinturones ubicados delante del pliegue del asiento Los cinturones de seguridad del vehículo ubicados delante del pliegue en el asiento quizá no sujeten bien el asiento. Consulte el manual del propietario del vehículo o visite el concesionario del vehículo para informarse sobre los requisitos de instalación de los asientos.
Page 70
CINTURONES DE SEGURIDAD DEL VEHÍCULO ❃ Cinturones de regazo - ajustables manualmente La placa de cierre en algunos cinturones de seguridad se puede deslizar y soltar tras abrocharla al asiento en ciertos ángulos. En este caso, dé la vuelta a la placa de cierre (fig. a) y vuelva a abrocharla.
Page 71
CINTURONES DE SEGURIDAD DEL VEHÍCULO ❃ Cinturón pasivo - cinturón de regazo con cinturón de hombro motorizado NO SE DEBE usar con ningún asiento. ❃ Cinturón pasivo - cinturón de regazo y hombro montado en la puerta NO SE DEBE usar con ningún asiento. Los cinturones no se mantendrán apretados durante el manejo del auto.
Page 72
CINTURONES DE SEGURIDAD DEL VEHÍCULO ❃ Cinturón combinado de regazo / hombro con placa de cierre deslizante Jale la placa de cierre (fig. a). Si el cinturón se desliza fácilmente por la placa de cierre, SE DEBE utilizar un clip de cierre (vea la sección "Clip de cierre"...
CINTURONES DE SEGURIDAD DEL VEHÍCULO ❃ Clip de cierre ADVERTENCIA Evite lesiones graves o la muerte: • No usar el clip de cierre cuando se requiere impide que el asiento quede bien sujeto. • Quite el clip de cierre de los cinturones de seguridad cuando no lo utilice con el asiento.
INFORMACIÓN ADICIONAL ❃ Almacenaje del anclaje NO conecte la correa de anclaje superior al vehículo al utilizar el asiento orientado hacia atrás. El gancho del anclaje debe conectarse cuando el asiento se usa en orientación trasera vehículo no viene equipado con los anclajes correspondientes.
INFORMACIÓN ADICIONAL ❃ Portabebidas Disponible en algunos modelos: • Ubique la ranura en el reposabrazos debajo de la almohadilla del reposabrazos en uno o otros lados del asiento para el automóvil. • Trabe el portabebidas en la ranura en el lado de asiento.
INFORMACIÓN ADICIONAL ❃ Cuidado y limpieza Retirar la almohadilla: Retire los dos bucles de las correas del arnés de la placa de unión de la parte trasera del asiento y páselos por la parte delantera de la almohadilla. Desabroche el cierre del arnés, (vea las páginas 20 y 21, fig.
Instale el asiento en la aeronave de la misma manera que se instala en un vehículo, cuando se usa el cinturón de seguridad del vehículo. ❃ Asiento para autos de segunda mano Graco Children's Products Inc. desaconseja prestar o regalar el asiento.
El pedido debe ir acompañado del pago correspondiente. Las piezas también se pueden pedir desde el sitio Web de Graco en www.gracobaby.com. Almohadilla de tela del asiento (todos los modelos) ... 35.00 Almohadilla de tela para la barra (barra protectora) ...
Page 79
Nombre Dirección Cuidad, Estado, Código postal Teléfono (incluido código de área) Dirección E-mail Se adjunta cheque o giro postal (a nombre de Graco Children's Products Inc.) Cóbrese a la tarjeta de crédito Visa MasterCard N° de cuenta Fecha de vencimiento Firma N°...
1-610-286-4555. o escríbanos a: Graco Children’s Products P.O.Box 100 Elverson, PA 19520-9974 Atención: Departamento de Servicio al Cliente Guarde aquí el clip de cierre. Graco Children’s Products Inc. Una división de Newell Rubbermaid P.O. Box 100 Elverson, PA 19520...