Blaupunkt BERLIN RCM 303A Installation Instructions Manual

Fitting instructions
3 D93 653 072
Safety advice
Installation and hook-up regulations
Disconnect the negative pole of the battery while this unit is being
installed and hooked up.
Before drilling any holes, ensure that any wires or car parts (such as the
air bag when mounting the display, or the tank or petrol line) will not be
damaged.
Use wire bushings to protect the wires which pass through holes with
sharp edges.
To prevent interference, lay all wires a safe distance away from any wire
harnesses.
Use only those loudspeakers with an impedance of 4 Ω. Be sure to take
the maximum load capacity (music) into account.
Do not ground the loudspeakers.
Use only the marked terminals. In order to ensure a safe installation, use
only the attached original mounting material.
Fuses:
Operating panel (ACR):
Tuner:
Amplifier:
CDC interface:
CD changer:
Before proceeding with the installation
Antennas
Use the vehicle-specific bar or window antenna as antenna 1 for AM and
FM reception. Due to anexcessive attenuation of the antenna duplexer,
do not employ a combi-antenna for car radio and telephone.
Before installing the ADA window antenna, look for an interference-free
mounting spot with the help of a portable radio while the engine is
running. In the table you will find possible layout plans for the ADA
window antenna. In order to prevent any interference, lay the antenna
wire far enough away from wire harnesses or other interference sources
(under the inside roof lining, if possible).
If installing the antenna on the rear window, do not fix the wire to the rear
window heating wires. Install the antenna wires either above or beneath
the heating wires only, whereby you must make sure that there are at
least 10 cm between the chassis and the heating wires.
Install the antenna wires as instructed in the installation instructions
provided with the antenna.
Installation material
Check to make sure that you have all the electrical and mechanical
material you need for installing the individual components and divide this
material into groups (refer to the installation material for the individual
components).
It is advisable to mark the optical wave guides for each individual
component.
GB
7 642 997 010
GB
3.15 A internal fuse
4 A wire fuse
30 A wire fuse
3.15 A internal visible type fuse
2.5 A soldered fuse
Multi media system
Berlin RCM 303 A
Connecting wires
To hook up the power supply for the components instal
led in the boot (tuner, CDC interface, amplifier), hook up the 6 mm˝
positive wire of the amplifier via the 30 A wire fuse to the positive pole of
the battery and lay it into the boot. Hook up the positive wire of the tuner
and the CDC interface to this cable (solder it, or use a plug-in or screw
connection).
In order to earth the amplifier, lay the brown 6 mm˝ earth wire from the
negative pole of the battery to the amplifier in the boot. Lay the CORA bus
wire from the operating panel (ACR) to where the tuner, CDC interface
and the amplifier have been installed. Lay the ACR's optical wave guide
and the wire of the measuring microphone to the amplifier.
Initial start-up
After the installation has been completed, re-connect the negative pole
of the battery. Press the volume, on/off button. The display should show
a frequency and the word
Suchlauf
Scan
and the unit is now operating in the tuner mode. After a time (depending
on the number of stations which can be received, approximately 2
minutes), the station names (RDS stations) and their frequencies will be
visible in the display.
Check all of the functions (cassette, CD player, AUX, if necessary). For
the CD player, the entire magazine will be tested. The following message
will appear in the display: „Magazine testing in progress". At least one CD
must be in the magazine. After the test, the unit will switch into CD mode.
If any error messages appear in the display, test the system with the help
of the trouble-shooting information at the end of these installation
instructions.
After completing the installation and testing all of the individual
components, proceed with the Hi-fi sound and DNC adjustment as
described in the information about the measuring microphone.
Modifications reserved!
1