1. Manuals
  2. Brands
  3. Fujitsu Manuals
  4. Battery Charger
  5. FPCBC27
  6. User manual

Fujitsu FPCBC27 User Manual

Battery charging station
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
F u j i t s u A m e r i c a , I n c .
Battery Charging Station
User's Guide
This user's guide contains information on using the dual battery
charger. We strongly recommend that you read this guide before
using the battery charger.
BATTERY CHARGER COMPONENTS
The battery charging station (referred to in this document as the
"charger") is a versatile device that allows you to charge a
variety of different battery packs simultaneously.
The charger consists of the following components:
• Charger base with built-in AC adapter
• U. S. power cord
Additionally, removable adapter modules are required to
accommodate your specific battery types. The adapter
modules must be ordered separately from the charger.
BATTERY CHARGER FEATURES
Refer to Figure 1 for the location of the following features.
The charger base holds the adapter modules
Charger Base.
and contains the power supply.
The power indicator shows whether power
Power Indicator.
is applied to the charger. When the power cord is disconnected
and/or the power switch is shut off, this indicator is off. When
power is applied, this indicator is solid green.
Each of the battery bays has two LEDs asso-
Indicator LEDs.
ciated with it: The upper LEDs indicate charge level (as detailed
in the table below); the lower LEDs indicate a battery error.
1

Advertisement

Table of Contents
loading

Related Manuals for Fujitsu FPCBC27

Summary of Contents for Fujitsu FPCBC27

  • Page 1 F u j i t s u A m e r i c a , I n c . Battery Charging Station User’s Guide This user’s guide contains information on using the dual battery charger. We strongly recommend that you read this guide before using the battery charger.
  • Page 2 Condition Meaning Charge Level Green, solid 100% charged (upper LEDs) Green, blinking 50-99% charged Orange, blinking 12-50% charged Red, blinking 0-12% Standby Charger in Red, solid (upper LEDs) standby Lights for a few Battery Detection Orange, solid seconds when (upper LEDs) battery detected.
  • Page 3 Battery Connectors Adapter Module Module Locks Module Indicator LEDs Charger Base Power Indicator LED Figure 1. Dual Battery Charger, front (without Adapter Modules) Power Switch Power Cable Connector Figure 2. Dual Battery Charger, rear (without Adapter Modules)

  • Page 4: Installing A Module

    The adapter modules bays each hold Adapter Module Bays. an adapter module. A variety of modules are available, and each is designed to accept a different Fujitsu battery. The power cable Supplies power to the charger. Power Cable. The power switch turns AC power on and off.
  • Page 5 1. Ensure the power cable is disconnected from the charger. 2. Select the correct adapter module(s) for the battery(s) you want to charge in one or both of the bays. 3. Position the battery plug access hole and the hole below it over the two adapter guides on the battery charger base (see Figure 4).

  • Page 6: Installing A Battery

    Batteries will only fit correctly in one orientation. In the following steps, be sure the battery is oriented correctly before installing it. When the edge of the battery is flush with the front of the charger, the connector on the bottom of the battery should be aligned with the connector on the adapter.

  • Page 7: Removing A Battery

    • When disconnecting the power cord, do not pull on the cable. Always remove by grasping the plug body. • If the battery charger smokes, smells hot, heats abnormally, or makes noise, disconnect the power cord, and contact your Fujitsu reseller (see “Fujitsu America Contact Information”...
  • Page 8 below). It is normal for the charger to become slightly warm during charging. • Do not use the battery charger in humid, dusty, or poorly ventilated places or if any foreign substance, such as water or dirt has gotten inside. •...
  • Page 9 Rotating hook Figure 5. Connecting two charging stations (bottom)

  • Page 10: Technical Support

    TECHNICAL SUPPORT Fujitsu America contact information If you have problems you are unable to resolve, consult your support representative at: • 1-800-8FUJITSU (1-800-838-5487) • Web Site: http://www.computers.us.fujitsu.com/support CHARGER SPECIFICATIONS Specification Details Power Requirements 100-240 V, ~ 50-60 Hz Operating Temperature 5°C –...

  • Page 11: Declaration Of Conformity

    • Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party respon- sible for compliance could void the user’s authority to operate the equipment. Model Name: Battery Charger FPCBC27 72/23/EEC, Conformance to Directive(s)/Product Standard: EN60950-1:2006; IEC60950-1:2005; EN55022: 2006, EN61000-3-2: 2000+A2: 2005, EN 61000-3-3: 1995+ A1: 2001+A2: 2005;...
  • Page 12 Fujitsu America, Inc. 1250 E. Arques Avenue, Sunnyvale, California 94085 For more information, call 1-800-FUJITSU or visit our Web site at: www.ShopFujitsu. For technical support call:1-800-8FUJITSU (1-800-838-5487) Fujitsu and the Fujitsu logo are registered trademarks of Fujitsu Ltd. All other trademarks mentioned herein are the property of their respective owners.

Table of Contents