Table of Contents
Advertisement
After having removed the knob once again, making sure that the
thermostat rod has not been moved, screw slightly the above
mentioned by-pass screw, to obtain a flame of 3 or 4 mm of length.
For butane/propane gas, the adjusting screw must be tight screwed.
Make sure that the flame does not extinguish passing quickly from
the maximum flow to the minimum flow, and closing and opening
the oven door (the oven door must be closed softly).
Attention: for taps with safety device, the minimum adjusting screw
"T" is on the outside of the tap rod (fig. I ).
T
Fig. H
Fig. I
REGULATION AIR ADJUSTER
REGULATION OF AIR ADJUSTER
(oven burner )
To do this,
- Unscrews the screw (A ) in order to rotate the metal ring at the
end of the burner (fig L ).
In this way, entrace of the air increases or descreases, obtaining
a correct flame.
Be sure that the flame does not lift or light back or present a
yellow colouration .
REGULATION OF AIR ADJUSTER
(grill burner )
To do this,
- Unscrews the screw (A ) in order to slip it forwards or backwards
(fig M).
In this way, entrace of the air increases or descreases, obtaining
a correct flame.
Be sure that the flame does not lift or light back or present a
yellow colouration .
A
A
Fig. L
Fig. M
APPLIANCE MAINTENANCE
WARNINGS
Isolate the cooker from the electricity supply before attempting to
replace the oven lamp.
The oven lamp used is of a special type withstanding high
temperatures. To replace it, act as follows: disassemble the
protecting glass (A) and replace the burnt lamp with one of the
same type. Reassemble the protecting glass.
E 14
25 W - 230 V~
T300°C
A
GB
DISASSEMBLE OF WORK-TOP
In case it is necessary to repair or replace the inside components,
act as follows:remove the glass lid from its position slipping off it
upwards.
Remove the grids, remove burners and flame-spreaders (see
fig. 13), unscrew the visible screws "V" placed on the work-top
(see fig. 14). Disassemble the work-top by unscrewing the 4 rear
screws "A" (see fig. 15 ).
V
Fig. 13
Fig. 14
A
Fig. 15
- To disassemble the control panel, unscrew the 4 internal screws
(B) fixing the control panel to the oven face ( fig 16 ).
Fig. 16
GREASING OF TAPS
WARNING:This operation must be carried out by skilled staff.
If a tap becomes hard to be turned, grease it using a specific
grease withstanding high temperatures. Act as follows: switch the
appliance off, and close the gas tap open the work-top and
disassemble also the control panel as described on the previous
paragraph. Unscrew the two fixing screws from the burner body
(see picture) and remove the cone.
Clean the cone and its slot by means of a cloth soaked with diluent.
Slightly grease the cone with the relevant grease, put it in its slot,
and turn it some times. Remove the cone again, remove the
exceeding grease making sure the gas entries are not obstructed
by grease residuals. Assemble everything carefully in the opposite
direction check the connection seal by means of soapy water.
TAPS REPLACEMENT
Act as follows: switch the appliance off, and close the general tap
open the work-top and disassemble also the control panel as
described on the previous paragraph. Unscrew screw nut D of the
gas tube supplying the burner. Unscrew screw V fixing the tap to
the bridle and remove it (see picture).
Note: Every time the tap is replaced, it is necessary to replace the
seal gasket too check the connection seal by means of soapy
water (see picture).
D
V
7
10
B
A
Z
10
B
C
C
Advertisement
Table of Contents
