Interconnection Example: Vice Versa - Hifonics X3-ZEUS Owner's Manual

2-CHANNEL AMPLIFIERS: X3-ZEUS / X3-COLOSSUS
VICE VERSA
The so-called VICE VERSA outputsignal is a special crossover configuration, which is only applicable, if the LINE OUT of the HIFONICS
X3-ZEUS or X3-COLOSSUS amplifier is used to provide an audiosignal to an additional amplifier. The complete crossover modifications
for both amplifiers are only done by the HIFONICS X3-amplifier. On amplifier 2 no crossover modifications are necessary, because amplifier
2 gets a already modificated signal by the HIFONICS X3-amplifier.
In LP/BP-Mode (Example 1) a highpass signal will be transferred to amplifier 2.
In HP-Mode (Example 2) a lowpass signal will be transferred to amplifier 2.
Here are two examples for the VICE VERSA function:
VICE VERSA 1
HiFONICS X3-ZEUS / X3-COLOSSUS
for subwoofer operation (mono)
X-OVER MODE
LINE INPUT
L STEREO 12dB
MONO 24dB
SUBSONIC LOW PASS
VICE VERSA
LINE OUTPUT SIGNAL
R
BALANCED INPUT
Connect to head unit
Settings HiFONICS X3-Amplifier:
The X3-Amplifier must be in LP/BP mode, this means the on this amplifier interconnected
speaker or subwoofer is provided with a lowpass/bandpass-signal.
Now the VICE VERSA outputsignal on LINE OUT could be modified by the HIGH PASS-
controller of the X3-amplifier.
ADVANTAGE:
This VICE VERSA-constellation affords you to use the high power effciency of a X3-ZEUS or X3-COLOSSUS amplifier for the interconnected subwoofer and to use at the same
time the very high-valued highpass filter (variable between 10 - 4000 hz) also as the audiophile sound characteristics for the to amplifier 2 transferred and already modified audiosignal.
Thereby amplifier 2 works as pure power-amplifier without any pre-amplifier modifications and provides the usual X3-amplifier high-end-sound for the interconnected speakers,
without beeing a X3-model. As a matter of course this constellation also works with two X3-models.
VICE VERSA 2
HiFONICS X3-ZEUS / X3-COLOSSUS
for stereo-speaker-system (high pass-mode)
X-OVER MODE
LINE INPUT
L STEREO 12dB
MONO 24dB
SUBSONIC LOW PASS
VICE VERSA
LINE OUTPUT SIGNAL
R
BALANCED INPUT
Connect to head unit
Settings HiFONICS X3-Amplifier:
The X3-Amplifier must be in HP mode, this means the on this amplifier interconnected
speakers are provided with a highpass-signal.
Now the VICE VERSA outputsignal on LINE OUT could be modified by the LOWPASS-
and SUBSONIC controller of the X3-amplifier.
ADVANTAGE:
This VICE VERSA-constellation affords you to the very high-valued highpass filter (variable between 10 - 4000 hz) also as the audiophile sound characteristics of a X3-ZEUS or
X3-COLOSSUS amplifier for the interconnected speakers and to use at the same time the very dynamic high-valued bass-filters (lowpass 40 - 4000 Hz and subsonic 10 - 150
Hz) for the to amplifier 2 transferred and already modified audiosignal. Thereby amplifier 2 works as pure power-amplifier without any pre-amplifier modifications and provides the
usual X3-amplifier high-end-bass-sound for the interconnected subwoofer, without beeing a X3-model. As a matter of course this constellation also works with two X3-models.
INTERCONNECTION EXAMPLES: VICE VERSA
POWER
LINE OUTPUT
PROTECT
HIGH PASS LEVEL BASS BOOST
REMOTE IN REMOTE OUT
CINCH/RCA LINE OUT
POWER
LINE OUTPUT
PROTECT
HIGH PASS LEVEL BASS BOOST
REMOTE IN REMOTE OUT
CINCH/RCA LINE OUT
AMPLIFIER 2 (any device)
for stereo-speaker-system (high pass-mode)
LOGO
BADGE
PROTECT
BASS BOOST
LP/BP
BLUE
WHITE
POWER
0dB 18dB
ZXi 9002
2 x 450 Watts
Settings amplifier 2:
The additional amplifier must be switched to FULL operationmode (Fullrange)
for the regular loudspeaker operation.
The crossover settings will be taken over by the X3-Amplifier. Only the level
controllers needs to be aligned accordingly. Attend in this case the owner's manual
of the regarding amplifier.
NOTE: If amplifier 2 owns a variable lowpass-filter, it's possible to generate a
bandpass-signal (e.g. for providing kickbass woofers).
AMPLIFIER 2 (any device)
for subwoofer operation (mono)
LOGO
BADGE
PROTECT
BASS BOOST
LP/BP
BLUE
WHITE
POWER
0dB 18dB
ZXi 9002
2 x 450 Watts
Einstellungen Verstärker 2:
The additional amplifier must be switched to FULL- or FLAT operation mode
(Fullrange).
The crossover settings will be taken over by the X3-Amplifier. Only the level
controllers needs to be aligned accordingly. Attend in this case the owner's manual
of the regarding amplifier.
24
LINE OUTPUT LINE INPUT
X-OVER
LOW PASS HI PASS LEVEL
CH 2
HP FULL
30Hz 150Hz 10Hz 1.2kHz 6V 0.2V
REMOTE
CH 1
CINCH/RCA LINE IN
LINE OUTPUT LINE INPUT
X-OVER
LOW PASS HI PASS LEVEL
CH 2
HP FULL
30Hz 150Hz REMOTE 10Hz 1.2kHz 6V 0.2V
CH 1
CINCH/RCA LINE IN