Advertisement
Quick Links
PARTS LIST
QTY.
PART NO.
1
N925
Bag 154
6
80-850000-000
2
49-490521-000
2
50-571100-000
REPLACEMENT PARTS and ACCESSORIES
Order parts through your local dealer or contact National Cycle.
Description
Light Head Assembly
Lamp Assembly E13/DOT
Reflector, Lens and Bulb
Halogen H3 Bulb
Turn Signal
Assembly
Turn Signal Lens
Turn Signal Bulb Only: Bulb 1157 Available at Most Auto Parts Stores.
Light Bar Accessories
Chrome Visor
Alternate Thumb Switch
Left and Right side of motorcycle is determined
while sitting on the bike.
PREPARATION VN1500D and VN800B
Make certain the motorcycle is positioned securely
on its sidestand or a work stand.Cover the front
fender to avoid scratches due to a dropped part or
tool.
2. Remove the head lamp from the Headlight Shell
(Screwdriver), set aside.
3. Disconnect Turnsignal Wires Inside headlight Shell.
4. Remove Turnsignals: (Refer to the motorcycle owner's
manual)
DESCRIPTION
Light Bar Assembly
Scotchlok Connectors
Washer Flat (for VN1600 only)
Screw, M6 x 16 (for VN1600 only)
N925
Part No.
90-910501-000
90-901011-000
90-901015-000
90-930921-000
90-930213-000
N9005
N9001
INSTALLATION AND OWNER'S MANUAL
Light Bar N925 for Installation to:
Kawasaki
VN1500D&E and VN800B Pages 1,2,3 and 5
®
Kawasaki
®
TOOL LIST VN1500D&E and VN800B Installation
Tools needed to remove fuel tank.
Screw Driver, #2 Phillips
Socket 10mm and Ratchet Wrench
Socket 27mm, 3" Extension and Wrench
Hex Key Wrench, 5mm
Slip Joint Pliers
Floor Jack capable of lifting front of motorcycle.
Motorcycle Owner's Manual
TOOL LIST VN1600 Installation
Screw Driver, #2 Phillips
Screw Driver, Flat Blade
8mm Wrench
Slip Joint Pliers
Motorcycle Owner's Manual
Special notes and cautionary measures
which can prevent damage to the motor-
cycle.
Tips for facilitation of operation, control
and adjustment, as well as maintenance
work.
PREPARATION VN1600
Make certain the motorcycle is positioned securely on
its sidestand or a work stand.Cover the front fender
to avoid scratches due to a dropped part or tool.
Page 1 of 5
VN1600 Pages 1, 4 and 5
10-110725-000
06/03
Advertisement
Related Manuals for National Cycle N925
Summary of Contents for National Cycle N925
- Page 1 Slip Joint Pliers Floor Jack capable of lifting front of motorcycle. Motorcycle Owner’s Manual REPLACEMENT PARTS and ACCESSORIES TOOL LIST VN1600 Installation Order parts through your local dealer or contact National Cycle. N925 Screw Driver, #2 Phillips Description Part No.
- Page 2 INSTALLATION VN1500D&E and VN800B 1. Loosen the pinch bolts on the upper Triple Clamp (5mm Hex Key). 2. Remove the bolt at the center of the upper Triple Clamp (27mm Socket). 3. Lift the front of the motorcycle so there is no weight on the front wheel (Floor Jack).
- Page 3 WIRE THE LIGHT BAR VN1500D&E and VN800B Wire the Light Bar Assembly 1. Route the Light Bar Assembly wires over the Triple Clamp and into the Headlight Shell. 2. Attach the wires according to the Right and Left Side Instructions Below. (Scotchlok connectors & Slip Joint Pliers) Watch the instruction for the differences in wire color between the VN1500 and VN800.
- Page 4 INSTALLATION - SETUP VN1600 1. Remove the screws from the sides of the headlight shell (Phillips screwdriver). Gently pry the headlight ring from the shell- there is a notch for this on the left side of the shell Route (flat screwdriver). Disconnect the plug on the back of the wires to headlight and set the headlight assembly and screws aside this notch...
- Page 5 M. Verify operation of the lights. MAINTENANCE AND CARE The high quality chrome finish of your National Cycle light bar can bemaintained with any quality chrome cleaner and /or polish. Replacement Parts: Refer to page 1. National Cycle, Inc. PO Box 158 Maywood, IL 60153-0158...