Advertisement
Operation Guide 3218 3289
Tide/Moon Data Screens
In the Tide/Moon Data Mode, press
to toggle between the tide data screen and the
Moon data screen.
Tide Data Screen
Month – Day
Current tide range
Press
Time
Current
tide level
E-20
To adjust the high tide time
1. In the Tide/Moon Data Mode, hold down
hour digits start to flash.
2. Use
(+) and
3. When the hour is the setting you want, press
This will cause the minute digits to flash.
4. Use
(+) and
5. When the minute setting is the way you want, press
Hour
to exit the adjustment screen and return to the Tide/
Moon Data Mode screen.
Pressing
and
adjustment screen is displayed (steps 2 through 5
above) will return the high tide time to its initial factory
default setting.
The high tide time setting is not affected by the DST
(summer time) setting of the Timekeeping Mode.
Minute
E-22
To reverse the displayed Moon phase
1. In the Tide/Moon Data Mode, hold down
hour digits start to flash.
2. Press
twice.
This will cause the Moon phase indicator to flash. This
is the indicator switching screen.
3. Press
to toggle the Moon phase indicator between
the southerly view (indicated by
view (indicated by
Northerly view: Moon is north of you.
Southerly view: Moon is south of you.
4. When the Moon phase indicator setting is the way you
want, press
to the Tide/Moon Data Mode screen.
E-24
To view the time in another city
While in the World Time Mode, use the
(time zones).
Pressing the
and
at the same time will jump to the UTC time zone.
E-26
Alarms
The Alarm Mode gives you a choice of four one-time
Alarm number
alarms and one snooze alarm.
Also use the Alarm Mode to turn the Hourly Time Signal
(
) on and off.
There are five alarm screens numbered
and
alarm screen indicated by
Signal screen is indicated by
All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing
E-11).
Alarm time
(Hour : Minutes)
E-28
Moon Data Screen
Moon phase
Month – Day
.
Moon age
until the
(–) to change the hour setting.
.
(–) to change the minute setting.
at the same time while the time
until the
) and northerly
).
to exit the switching screen and return
(eastward) to scroll through the city codes
,
,
for the one-time alarm, and a snooze
. The Hourly Time
.
(page
When you display the Tide Data Screen, it initially shows tide data for 6:00 a.m.
Use the Tide Data Screen to specify the Tide Data time. You can use
change the displayed time in one-hour increments.
Use the Moon Data Screen to specify the Tide/Moon Data date. You can use
to change the displayed date in one-day increments. Pressing
year of the displayed date.
Adjusting the High Tide Time
Use the following procedure to adjust the high tide time within a particular date. You
can find out high tide information for your area from a tide table, the Internet, or your
local newspaper.
On some days, there are two high tides. With this watch, you can adjust the first high
tide time only. The second high tide time for that day is adjusted automatically based
on the first high tide time.
Reversing the Displayed Moon Phase
The left-right (east-west) appearance of the Moon depends on whether the Moon is
north of you (northerly view) or south of you (southerly view) as you view it.
You can use the procedure below to reverse the displayed Moon phase so it matches
the actual appearance of the Moon where you are located.
To determine the viewing direction of the Moon, use a compass to take a direction
reading of the Moon at its meridian passage.
For information about the Moon phase indicator, see "Moon Phase Indicator" (page
E-50).
World Time
World Time shows the current time in 48 cities (31 time
City code
zones) around the world.
The times kept in the World Time Mode are
synchronized with the time being kept in the
Timekeeping Mode. If you feel that there is an error in
any World Time Mode time, check to make sure you
have the correct city selected as your Home City. Also
check to make sure that the current time as shown in
the Timekeeping Mode is correct.
Select a city code in the World Time Mode to display the
Current time in
current time in any particular time zone around the
selected city
globe. See the "City Code Table" at the back of this
manual for information about the UTC differential
settings that are supported.
All of the operations in this section are performed in the
World Time Mode, which you enter by pressing
(page E-11).
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, use
(time zone) whose Standard Time/Daylight Saving Time
setting you want to change.
2. Hold down
(DST indicator displayed) and Standard Time (DST
indicator not displayed).
The DST indicator is shown on the World Time Mode
screen while Daylight Saving Time is turned on.
DST indicator
Note that the Standard Time/Daylight Saving Time
setting affects only the currently displayed city code.
Other city codes are not affected.
Note that you cannot switch between Standard Time
and Daylight Saving Time while UTC is selected as the
city code.
To set an alarm time
1. In the Alarm Mode, use
screens until the one whose time you want to set is
displayed.
To set a one-time alarm, display alarm screen
To set the snooze alarm, display the
The snooze alarm repeats every five minutes.
2. After you select an alarm, hold down
starts to flash, which indicates the setting screen.
This operation turns on the alarm automatically.
3. Press
to move the flashing between the hour and minute settings.
4. While a setting is flashing, use
(+) and
With the 12-hour format, set the time correctly as a.m. or p.m. (P indicator).
5. Press
to exit the setting screen.
(+) to
(+)
will display the
E-21
E-23
E-25
to display the city code
to toggle between Daylight Saving Time
E-27
to scroll through the alarm
,
,
or
.
screen.
until the hour setting of the alarm time
(–) to change it.
E-29
Advertisement
