OPTIONAL CHROMATHERAPY THANK YOU... for selecting an American Standard bath. Your new bath is shipped to you after careful inspection. The whirlpool and air bath versions are completely assembled with pump/blower and system piping. All you need to finish the installation are your selected fittings and electrical connections.
TABLE OF CONTENTS: Cover...Page 1 Table of Contents...Page 2 Safety Instructions Notice...Page 3 Installation, Framing and Post Installation Clean-Up Instructions...Page 4 Roughing-in References for Recess Type Installations...Page 5 Roughing-in References for Pier Type Installations...Page 6 Under Deck Mounting Instructions...Page 6 Roughing-in References for All Model Series...Pages 7 - 26 Electrical Installation Instructions...Pages 27 - 32 Whirlpool Heater Operation...Page 32...
Use this unit only for its intended use as described in this manual. Do not use any attachments not recommended by American Standard. The unit must be connected only to a supply circuit that is properly protected by a ground-fault circuit-interrupter (GFCI). Such a GFCI should be provided by the installer and should be tested on a routine basis.
Installation and Framing Instructions Each bath arrives ready for installation, completely equipped with the pump/blower electronics and plumbing necessary for operation. However, a drain/overflow kit is required for each bath and it is not included. The variety of installations for this bath may require framing procedures other than those shown. Locate studs as required.
FRONT EDGE OF BATH MUST BE SUPPORTED BY STUD WALL OR AMERICAN STANDARD APRON KIT UNLESS AN ACCESS OPENING OF AT LEAST 12" x 24" (305 x 610mm) IS PROVIDED, WARRANTY SERVICE WILL NOT BE PERFORMED. TYPICAL TILE FLANGE INSTALLATION...
ROUGH-IN REFERENCES FOR PIER TYPE INSTALLATIONS AS DESIRED MOUNTING SURFACE UNDER DECK MOUNTING INSTRUCTIONS Please note that care must be taken to protect the surface of the tub during all aspects of the installation. Do not drill or cut the bath deck with the tub directly beneath it as damage to the tub may result. 1.
SPECIFICATIONS: SIDE VIEW GENERAL SPECIFICATIONS FOR WHIRLPOOLS AND BATH TUBS Description Dimensions Drain / L-W-H Overflow 2664 L 83-1/2" (2121mm) A 16" Scala W 63-3/4" (1619mm) (406mm) Corner H 19-3/4" (502mm) B 13-1/4" (337mm) L 69-1/4" (1759mm) 2709 A 15"...
21-3/4" (552mm) CUTOUT DIMENSION 38-1/2" (978mm) 19-1/4" (489mm) (76mm) 754532-100 Rev. A ROUGH-IN REFERENCES MODEL SERIES 2664 10" x 10" (254mm x 254mm) DRAIN OUTLET CUTOUT 8-1/2" (216mm) 3/4"(19mm) 16" (406mm) OF DRAIN OUTLET MODEL SERIES 2709 69-1/4" (1759mm) 9-7/16"...
Page 9
ROUGH-IN REFERENCES MODEL SERIES 2711 (1829mm) 36-1/2" (927mm) 12" (305mm) 48" (1219mm) GRAB BAR RECOMMENDED FITTING AREA FITTING LOCATION 2-1/2" X 11" MODEL SERIES 2908 13" (330mm) 18" 9" X 12" (457mm) (229 x 305mm) FLOOR CUTOUT 36" (914mm) 2-1/2" REF. INTEGRAL (64mm) FITTING...
Page 10
11" (279mm) 18" (457mm) 35-3/4" (908mm) INTEGRAL FITTING DECK 5-1/2" (140mm) 4-1/4" (1073mm) 21-1/8" (537mm) 3" (76mm) 754532-100 Rev. A ROUGH-IN REFERENCES MODEL SERIES 2806 72" (1829mm) 9" x 13" (229 x 330mm) FLOOR CUTOUT C/L OF DRAIN OUTLINE OF CUTOUT OVERFLOW MODEL SERIES 2903 60"...
Page 11
ROUGH-IN REFERENCES MODEL SERIES 2742 4" (102mm) 35-3/4" (908mm) 13-1/4" (337mm) C/L OF DRAIN OUTLET 41-3/4" 26-3/4" (1060mm) (679mm) 3/4" (19mm) MODEL SERIES 2748 59-1/2" (1511mm) 29-7/8" (759mm) 14-1/2" (368mm) 41-5/8" (1057mm) PROVIDE ACCESS TO PUMP SERVING ON ALL INSTALLATIONS 71-1/2"...
Page 12
65-3/8" (1661mm) 13-5/8" (346mm) 5-5/8" (143mm) USE CUTOUT TEMPLATE SUPPLIED WITH PACKAGED PRODUCT. OUTLINE OF CUTOUT 70-1/2" x 34-1/2" (1791mm X 876mm) 36" (914mm) 11" (279mm) 754532-100 Rev. A ROUGH-IN REFERENCES MODEL SERIES 6060 76-3/4" REF. (1949mm) 38-3/8" (975mm) OUTLINE OF CUTOUT SEAT AREA 7"...
Page 13
SPECIFICATIONS: SIDE VIEW GENERAL SPECIFICATIONS FOR STUDIO 5' X 32" WHIRLPOOLS AND BATH TUBS Description Deck Dimensions Trim L-W-H Option L 59-1/2" (1511mm) 2932 Zero Studio (5/8") W 31-1/2" (800mm) 5' x 32" H 22-1/2" (572mm) 2932 2" L 59-3/4" (1518mm) Studio W 31-3/4"...
Page 14
SPECIFICATIONS: SIDE VIEW GENERAL SPECIFICATIONS FOR STUDIO 5' X 36" WHIRLPOOLS AND BATH TUBS Description Deck Dimensions Trim L-W-H Option 2934 Zero L 59-1/2" (1511mm) Studio (5/8") W 35-1/2" (902mm) H 22-1/2" (572mm) 5' x 36" 2934 2" L 59-3/4" (1518mm) Studio W 35-3/4"...
Page 15
SPECIFICATIONS: SIDE VIEW GENERAL SPECIFICATIONS FOR STUDIO 5-1/2' X 36" WHIRLPOOLS AND BATH TUBS Description Deck Dimensions Trim L-W-H Option L 65-1/2" (1664mm) 2938 Zero Studio (5/8") W 35-1/2" (902mm) 5-1/2' x 36" H 22-1/2" (572mm) 2938 2" L 65-3/4" (1670mm) Studio W 35-3/4"...
Page 16
SPECIFICATIONS: SIDE VIEW GENERAL SPECIFICATIONS FOR STUDIO 6' X 36" WHIRLPOOLS AND BATH TUBS Description Deck Dimensions Trim L-W-H Option 2940 Zero L 71-1/2" (1816mm) Studio (5/8") W 35-1/2" (902mm) 6' x 36" H 22-1/2" (572mm) 2940 2" L 71-3/4" (1822mm) Studio W 35-3/4"...
Page 17
SPECIFICATIONS: SIDE VIEW GENERAL SPECIFICATIONS FOR STUDIO 6' X 42" WHIRLPOOLS AND BATH TUBS Description Deck Dimensions Trim L-W-H Option A 17-3/4" 2942 Zero L 71-1/2" (1816mm) Studio (5/8") W 41-1/2" (1054mm) (451mm) B 10-3/4" 6' x 42" H 22-1/2" (572mm) (273mm) A 17-3/4"...
Page 18
SPECIFICATIONS: SIDE VIEW GENERAL SPECIFICATIONS FOR STUDIO CORNER WHIRLPOOLS AND BATH TUBS Description Deck Dimensions Trim L-W-H 2944 Zero L 83-15/16" (2132mm) Studio (5/8") W 61-3/8" (1559mm) Corner H 21-1/2" (546mm) 2944 2" L 84-1/4" (2139mm) Studio W 31-13/16" (808mm) Corner H 21-1/2"...
Page 19
SPECIFICATIONS: SIDE VIEW GENERAL SPECIFICATIONS FOR STUDIO CORNER WHIRLPOOLS AND BATH TUBS Description Deck Dimensions Trim L-W-H 2945 L 60" (1524mm) Studio W 32" (813mm) H 22" (559mm) 16-3/8" (411mm) 32" (813mm) END VIEW Drain / Height to Cut Out Rough-In Overflow Underside...
Page 20
SPECIFICATIONS: SIDE VIEW GENERAL SPECIFICATIONS FOR GREEN TEA WHIRLPOOLS AND BATH TUBS Description Dimensions Drain / L-W-H Overflow L 60" (1524mm) 3571 A 16" W 36" (914mm) Green Tea (406mm) H 21" (533mm) 5' x 36" B 11-1/2" (349mm) 3572 L 66"...
Page 21
ROUGH-IN REFERENCES MODEL SERIES 3571 CUTOUT IN FLOOR FOR DRAIN PROVIDE ACCESS TO PUMP SERVING ON ALL INSTALLATIONS OUTLINE OF CUTOUT 58.5" x 34.5" (1486 x 876mm) MODEL SERIES 3572 CUTOUT IN FLOOR FOR DRAIN PROVIDE ACCESS TO PUMP SERVING ON ALL INSTALLATIONS OUTLINE OF CUTOUT 64.5"...
Page 22
ROUGH-IN REFERENCES MODEL SERIES 3573 72" (1829mm) 14-3/4" (375mm) 11-1/2" (292mm) 36" (914mm) 9" (229mm) CUTOUT IN FLOOR FOR DRAIN PROVIDE ACCESS TO PUMP SERVING ON ALL INSTALLATIONS OUTLINE OF CUTOUT 70.5" x 34.5" (1780 x 876mm) MODEL SERIES 3574 60"...
Page 23
ROUGH-IN REFERENCES MODEL SERIES 3575 72" (1829mm) 14-3/4" (375mm) 11-1/2" (292mm) 42" (1067mm) 9" (229mm) CUTOUT IN FLOOR FOR DRAIN PROVIDE ACCESS TO PUMP SERVING ON ALL INSTALLATIONS OUTLINE OF CUTOUT 70.5" x 40.5" (1780 x 1029mm) 754532-100 Rev. A...
Page 24
SPECIFICATIONS: SIDE VIEW GENERAL SPECIFICATIONS FOR SERIN WHIRLPOOLS AND BATH TUBS Description Dimensions Drain / L-W-H Overflow A 16-3/4" L 60" (1524mm) 3581 (425mm) W 32" (813mm) Serin H 23" (584mm) B 10-1/4" 5' x 32" (260mm) A 16-7/8" L 66" (1676mm) 3582 (429mm) W 36"...
Page 25
ROUGH-IN REFERENCES MODEL SERIES 3582 (838mm) 9-3/4" (248mm) 36" (914mm) PROVIDE ACCESS TO PUMP SERVING ON ALL INSTALLATIONS 4" (102mm) MODEL SERIES 3583 (864mm) 11-1/2" (292mm) PROVIDE ACCESS TO PUMP SERVING ON ALL INSTALLATIONS INTEGRAL FAUCET DECK 4-3/4" (121mm) USE CUT-OUT TEMPLATE SUPPLLIED WITH PACKAGED TUB 66"...
Page 26
42" (1067mm) PROVIDE ACCESS TO PUMP SERVING ON ALL INSTALLATIONS FAUCET DECK 754532-100 Rev. A ROUGH-IN REFERENCES MODEL SERIES 3584 72" (1829mm) 36" (914mm) DRAIN 10-1/4" (260mm) INTEGRAL OUTLINE OF CUTPUT 9" x 12" (227 x 305mm) FLOOR CUTOUT 4-7/8" (124mm) OUTLINE OF SKID RESISTANT...
ELECTRICAL INSTALLATION INSTRUCTIONS All wiring must be performed by a licensed electrician in accordance with the national electrical code and all other applicable codes. WARNING: When using electrical products, basic precautions should always be observed, including the following: 1. DANGER: RISK OF ELECTRIC SHOCK! Connect only to a circuit protected by a ground-fault circuit interrupter. 2.
ELECTRICAL INSTALLATION INSTRUCTIONS (continued) Ensure the heater and pump are properly GROUNDED and BONDED as required. Attach the 8 AWG solid copper conductor supplied with the heater from the heater bonding lug to the motor frame bonding lug as shown in Figure 3. The conductor is secured to the lugs using set screws.
REMOTE BLOWER LOCATION OPTION IMPORTANT! It is not necessary that the blower motor be relocated. This option is provided for the case that a particular installation makes this effort practical. NOTE: Relocating blower motor from factory installed location, see photo 1, will require disassembly of air blower from mounting board.
Page 34
REMOTE BLOWER LOCATION OPTION (continued) FOR THE COMBINATION WHIRLPOOL / AIR BATH CONFIGURATIONS ONLY: Up to two additional control box extensions (P/N 754512-0070A) are required as shown in photo 4 (below). Simply extend the cables going to the blower by adding in the extension cables. Be careful not to damage the cable connections and never plug in cables while power is applied to blower and/or pump.
Operation: Single Speed Whirlpool AIR SWITCH BATHING: • Fill bath with water at a comfortable bathing temperature - If your whirlpool is equipped with the optional EZ-Heater, it will automatically maintain the water temperature. • IMPORTANT: Do NOT fill the whirlpool more than 2/3 full before getting in, as it may overflow. •...
Operation: EcoSilent Whirlpool with Lights 3-BUTTON ELECTRONIC SWITCH BATHING: • Fill bath with water at a comfortable bathing temperature - If your whirlpool is equipped with the optional EZ-Heater, it will automatically maintain the water temperature. • IMPORTANT: Do NOT fill the whirlpool more than 2/3 full before getting in, as it may overflow. •...
BATHING: • Close drain by rotating Drain Overflow Knob COUNTER-CLOCKWISE • Fill bath with water at a comfortable bathing temperature, adding bath oils or salts as desired. OPERATING AIR MASSAGE SYSTEM: ON/OFF: Press this button once to turn air-blower on. Press again to turn air-blower off.
Operation: Air Bath with Lights BATHING: • Close drain by rotating Drain Overflow Knob COUNTER-CLOCKWISE • Fill bath with water at a comfortable bathing temperature, adding bath oils or salts as desired. OPERATING AIR MASSAGE and CHROMATHERAPY SYSTEM: ON/OFF: Press this button once to turn air-blower on. Press again to turn air-blower off.
Page 39
Operation: Air Bath with Lights (continued) EXITING THE BATH • Be sure to turn off the air blower before draining bath. • Open drain by rotating drain knob clockwise. STANDARD DRYING CYCLE An automatic drying cycle will start 20 minutes after the blower is turned off. The blower LED blinks while waiting for the purge cycle.
Operation: Combination Tub with Lights BATHING: • Close drain by rotating Drain Overflow Knob COUNTER-CLOCKWISE • Fill bath with water at a comfortable bathing temperature, adding bath oils or salts as desired. OPERATING AIR MASSAGE and CHROMATHERAPY SYSTEM: • Press this button to turn blower on. •...
Page 41
Operation: Combination Tub with Lights (continued) EXITING THE BATH • Be sure to turn off the air blower before draining bath. • Open drain by rotating drain knob clockwise. STANDARD DRYING CYCLE An automatic drying cycle will start 20 minutes after the blower is turned off. The blower LED blinks while waiting for the purge cycle.
Your American Standard whirlpool is designed to give you many years of pleasure with reasonable care and maintenance. Your new acrylic bathtub is tough, durable and easy to care for. The colors have been formulated to match other American Standard fixtures and enhance your choice of bathroom decorations. The high gloss surface will retain its lasting luster with proper care and maintenance.
AS America, Inc. (”American Standard”) warrants to the original consumer purchaser that it will, at its option, repair or replace this whirlpool or any of its parts that are found by American Standard, in its sole judgment, to be defective under normal residential use and maintenance so long as it is owned by the original consumer purchaser.