Sunbeam Air Conditioner Installation Instructions Manual
Hide thumbs
Also See for Air Conditioner:
- Installation instructions manual (9 pages) ,
- Installation instructions manual (6 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Sunbeam Air Conditioner
Summary of Contents for Sunbeam Air Conditioner
-
Page 1: Installation Instructions
Installation Instructions Through-the-Wall Air Conditioners PTT122006... -
Page 2: Table Of Contents
WALL SLEEVE BRAND: WHIRLPOOL (17 1/8” DEEP) WALL SLEEVE BRAND: FEDDERS (19 3/4” DEEP) WALL SLEEVE BRAND: WHITE-WESTINGHOUSE, FRIGIDAIRE, SUNBEAM, CARRIER 52F SERIES (22” DEEP) WALL SLEEVE BRAND: GENERAL ELECTRIC, HOTPOINT (16 7/8” DEEP) WALL SLEEVE BRAND: SEARS, CARRIER 51S SERIES (18 5/8”... -
Page 3: How To Install
• All wall sleeves used to mount the new air conditioner must be in sound structural condition and have a rear grille that securely attached to the sleeve or rear fl ange that serves as a stop for the air conditioner. - Page 4 Prepare the wall sleeve to install the new air conditioner. See the following pages of the manual for brand-specifi c installation instructions.
-
Page 5: Installation Kit
PRE-INSTALLATION If you are installing your air conditioner into an existing sleeve and there is an existing rear grille, the louvers will have to be bent as per the instructions at the beginning of each section. If this does not work, Remove the existing grille. -
Page 6: Wall Sleeve Brand: Emerson (15" Deep)
Screw and attach the other end of the ground wire to the unit, making sure the toothed washer is against the cabinet. Install the 1” x 1 1/2” x 84” stuffer seal between the wall sleeve and the air conditioner. Assemble and install the trim frame (see “Trim Frame Assembly” section of manual). -
Page 7: Wall Sleeve Brand: Fedders (19 3/4" Deep)
Screw and attach the other end of the ground wire to the unit, making sure the toothed washer is against the cabinet. Install the 1” x 1 1/2” x 84” stuffer seal between the wall sleeve and the air conditioner. Assemble and install the trim frame (see “Trim Frame Assembly” section of manual). -
Page 8: Wall Sleeve Brand: General Electric, Hotpoint (16 7/8" Deep)
Screw and attach the other end of the ground wire to the unit, making sure the toothed washer is against the cabinet. Install the 1” x 1 1/2” x 84” stuffer seal between the wall sleeve and the air conditioner. Assemble and install the trim frame (see “Trim Frame Assembly” section of manual). -
Page 9: Wall Sleeve Brand: Whirlpool (23" Deep)
Screw and attach the other end of the ground wire to the unit, making sure the toothed washer is against the cabinet. Install the 1” x 1 1/2” x 84” stuffer seal between the wall sleeve and the air conditioner. Assemble and install the trim frame (see “Trim Frame Assembly” section of manual). -
Page 10: Sunbeam (22" Deep)
Screw and attach the other end of the ground wire to the unit, making sure the toothed washer is against the cabinet. Install the 1” x 1 1/2” x 84” stuffer seal between the wall sleeve and the air conditioner. Assemble and install the trim frame (see “Trim Frame Assembly” section of manual). -
Page 11: Wall Sleeve Brand: Fedders, Friedrich (16 3/4" Deep)
Screw and attach the other end of the ground wire to the unit, making sure the toothed washer is against the cabinet. Install the 1” x 1 1/2” x 84” stuffer seal between the wall sleeve and the air conditioner. Assemble and install the trim frame (see “Trim Frame Assembly” section of manual). - Page 12 © 2006 Sunbeam Products, Inc. doing business as Jarden Consumer Solutions. All rights reserved. Sunbeam is a registered trademark of Sunbeam Products, Inc. used under license. ® Distributed by Petters Consumer Brands, LLC. 4400 Baker Road, Minnetonka, MN 55343. For service, support and warranty information, visit www.sunbeammajorappliances.com or in the US call 1-866-866-6283.