Download
Share
Print this page
Star Micronics SP500 Series Installation Sheet
  1. Manuals
  2. Brands
  3. Star Micronics Manuals
  4. Printer
  5. SP500 Series
  6. Installation sheet
Star Micronics SP500 Series Installation Sheet

Star Micronics SP500 Series Installation Sheet

Hide thumbs Also See for SP500 Series:
1
2
3
4
5
6
7
8

Advertisement

Quick Links

Download this manual See also: Technical Manual, User Manual
SP500 Series Printers
Installation sheet
系列打印机卷紙器
安装指南
500
SP
This installation sheet contains information for setting and rewinding
the paper for rewinder model printers.
Please refer to the SP500 series User's Manual for information not
contained in this sheet.
本安装指南包含関于放置和重卷打印机卷纸器纸張的信息。
関于本安装指南没有包含的信息，請参考 SP500 系列用戸手册。
80871320
( Rewinder Model )
1. UNPACKING
After unpacking the unit, check that all the necessary accessories are included in
the package.
１．开　箱
� 开拆箱后，请检查所需的全部附件是否都在箱里。
For models with tear bar
对撕纸型
1
ER
RO
R
FE
E D
F
O F
PO
W ER
For models with auto cutter
对自动切刀型
1
ER
RO
R
FE
E D
F
O F
PO
W ER
Printer
1 打印机
1
Ribbon cartridge
2 色帯盒�
2
Roll paper guide
3 卷纸導板�
3
Power cord
4 電源電纜
4
User's manual
5 用户手册
5
Rear cover
6 后盖
6
Switch blind
7 開関保護板
7
2
5
O N
3
7
4
6
O N
1
2
3
4
5
6
7
- 1 -

Advertisement

loading

Related Manuals for Star Micronics SP500 Series

Summary of Contents for Star Micronics SP500 Series

  • Page 1 For models with auto cutter 对自动切刀型 This installation sheet contains information for setting and rewinding the paper for rewinder model printers. Please refer to the SP500 series User’s Manual for information not contained in this sheet. W ER 本安装指南包含関于放置和重卷打印机卷纸器纸張的信息。 関于本安装指南没有包含的信息，請参考 SP500 系列用戸手册。...

  • Page 2: Setting The Paper

    SETTING THE PAPER Roll paper 2-1. For models with tear bar 1. Open the cover. 5. Insert the edge of the paper into the paper feeder (black plastic part). If inserted correctly, the edge of the paper will pass through the paper exit. 6.
  • Page 3 7. After the automatic paper feed has been completed, the POWER lamp (green) on 9. Fold the paper back so that it is held in place by the slit. the operating panel will blink. ９. 将纸回折，以固定在压纸条上。 ７ . 在自働進紙完成后，操作面板上的 POWER 灯（緑色）閃煉。 10.
  • Page 4 11. Grasp the center of the paper with your fingers to keep it from coming off of the rewinder and then set the rewinder shaft in the frame for the rewinder. 11. 用手指握住纸的中把它从卷纸器里拖出，然后将卷纸轴放入卷纸器的安装 架上。 13. After cutting the upper ply with the mechanical cutter, lose the cover and ress the FEED button one time.
  • Page 5 2-2. For models with auto cutter Roll paper 1. Open the cover. 5. Insert the edge of the paper into the paper feeder (black plastic part). If inserted correctly, the edge of the paper will pass through the auto cutter paper slit. Press the FEED button to cut the paper.
  • Page 6 7. After the automatic paper feed has been completed, the POWER lamp (green) on 10. Pass the lower ply through the bottom of the upright cutter. the operating panel will blink. 11. Cut the upper ply with the mechanical tear bar. 12.
  • Page 7 14. Fold the paper back so that it is held in place by the slit. 16. Grasp the center of the paper with your fingers to keep it from coming off of the rewinder and then set the rewinder shaft in the frame for the rewinder. 14.

  • Page 8: Removing The Paper

    17. Turn the rewinder shaft clockwise to take up the slack in the paper. Removing the paper Caution: If the paper tends to slack during use, use the same procedures to take 1. Remove the paper as a roll on the rewinder shaft from the rewinder. up that slack.