Casio 3202 Operation Manual

MO1004-EB
Congratulations upon your selection of this CASIO watch.
Applications
The built-in sensors of this watch measure barometric pressure, temperature and
altitude. Measured values are then shown on the display. Such features make this
watch useful when hiking, mountain climbing, or when engaging in other such outdoor
activities.
• The measurement functions built into this watch are not intended for taking
measurements that require professional or industrial precision. Values produced
by this watch should be considered as reasonable representations only.
• Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any
damage or loss suffered by you or any third party arising through the use of
this product or its malfunction.
About This Manual
Selecting a Mode
• The illustration below shows which buttons you need to press to navigate between
modes.
• In any mode (except when a setting screen, with flashing digits is on the display),
press B to illuminate the display.
World Time World Time
Mode Mode
General Functions (All Modes)
The functions and operations described in this section can be used in all of the modes.
Auto Return Features
• The watch returns to the Timekeeping Mode automatically if you do not perform any
button operation for two or three minutes in the Alarm Mode.
• The watch will return to the Timekeeping Mode automatically if you do not perform
any operation for about one hour after entering the Barometer/Thermometer Mode.
• If you leave a setting screen with flashing digits on the display for two or three minutes
without performing any operation, the watch exits the setting screen automatically.
Initial Screens
When you enter the World Time Mode or Alarm Mode, the data you were viewing
when you last exited the mode appears first.
Scrolling
The B and D buttons are used on the setting screen to scroll through data on the
display. In most cases, holding down these buttons during a scroll operation scrolls
through the data at high speed.
Timekeeping
PM PM Day of Day of Month Month
indicator indicator week week Day Day
Hour : Minutes Hour : Minutes Seconds Seconds
Graphic Graphic
Operation Guide 3202
Warning !
• Depending on the model of your watch, display text
appears either as dark figures on a light background, or
light figures on a dark background. All sample displays
in this manual are shown using dark figures on a light
background.
• Button operations are indicated using the letters shown
in the illustration.
• Note that the product illustrations in this manual are
intended for reference only, and so the actual product
may appear somewhat different than depicted by an
illustration.
Barometer/ Barometer/
Thermometer Mode Thermometer Mode
Countdown Countdown
Stopwatch Mode Stopwatch Mode Timer Mode Timer Mode
Use the Timekeeping Mode to set and view the current
time and date.
• In the Timekeeping Mode, the graphic in the center of
the display indicates the passage of seconds.
Things to check before using the watch
1. Check the Home City and the daylight saving time (DST) setting.
Use the procedure under "To configure Home City settings" to configure your Home
City and daylight saving time settings.
Important!
Proper World Time Mode data depend on correct Home City, time, and date settings
in the Timekeeping Mode. Make sure you configure these settings correctly.
2. Set the current time.
See "Configuring Current Time and Date Settings".
The watch is now ready for use.
Mode Reference Guide
Your watch has 7 "modes". The mode you should select depends on what you want to do.
To do this:
• View the current time and date in the Home City
• Configure Home City and daylight saving time (DST) settings
• Configure time and date settings
View the barometric pressure and temperature at your
current location
• View the altitude at your current location
• Determine the altitude differential between two locations
(reference point and current location)
View the current time in one of 48 cities (31 time zones)
around the globe
Use the stopwatch to measure elapsed time
Use the countdown timer
Set an alarm time
Timekeeping Mode Timekeeping Mode
Alarm Mode Alarm Mode
Configuring Home City Settings
There are two Home City settings: actually selecting the Home City and selecting
either standard time or daylight saving time (DST).
PM PM City City To configure Home City settings
indicator indicator code code
1. In the Timekeeping Mode, hold down A until the
currently selected city code (Home City) starts to flash.
This is the city code setting screen.
• Before the city code starts to flash, the message
SET Hold will appear on the display. Keep A
depressed until SET Hold disappears and the city
code starts to flash.
• The watch will exit the setting mode automatically if
you do not perform any operation for about two or
three minutes.
Hour : Minutes Hour : Minutes Seconds Seconds
• For details about city codes, see the "City Code
Table".
2. Press D (East) and B (West) to select the city code
DST indicator DST indicator
you want to use as your Home City.
Keep pressing D or B until the city code you want
•
to select as your Home City appears on the display.
3. Press C to display the DST setting screen.
4. Press D to toggle between Daylight Saving Time (On)
and Standard Time (OFF).
• Note that you cannot switch between standard
time and daylight saving time (DST) while UTC is
Setting Setting selected as your Home City.
5. After all the settings are the way you want, press A to return to the Timekeeping Mode.
• The DST indicator appears to indicate that Daylight Saving Time is turned on.
Note
• After you specify a city code, the watch will use UTC* offsets in the World Time
Mode to calculate the current time for other time zones based on the current
time in your Home City.
* Coordinated Universal Time, the world-wide scientific standard of timekeeping.
The reference point for UTC is Greenwich, England.
Enter this mode:
Timekeeping Mode
Barometer/Thermometer
Mode
Altimeter Mode
World Time Mode
Stopwatch Mode
Countdown Timer Mode
Alarm Mode
Altimeter Mode Altimeter Mode
1