Tools And Building Supplies; Installation Procedure; Locating The Fireplace; Adjacent Walls - Lennox ELITE ME43 Installation Instructions Manual

Failure to use LHP parts or conduct varia-
tions in techniques and construction materi-
als described in this installation manual may
create a serious fire hazard and may void the
warranty and the WHI listing.
3. Always check your local building codes.
The installation must comply with their
regulations. Before beginning the installa-
tion, consult the local authorities and make
sure your building permit complies with
their requirements.
4. These fireplaces must be installed with Se-
curity Chimneys FTF8 (8" inside diameter)
chimney System only. These systems are
intended for use in any application where a
traditional masonry type fireplace would
apply. The chimney system must always
vent to the outside of the building.
5. To maintain top efficiency and to prevent
build-up of soot and creosote, inspect and
clean the chimney periodically during the
heating season.
6. To prevent possible hazards due to poor
combustion and to avoid affecting other fuel
burning appliances (furnace, wood stove,
etc.), ensure that the outside air kit is prop-
erly installed.
7. This fireplace is designed to allow the instal-
lation of a gas burner. In such a case, the
installation must conform with the National
Gas Code ANSI Z223.1 and Z21.60.
WARNING: WHEN USING A GAS BURNER,
IT IS MANDATORY TO KEEP THE CHIM-
NEY OUTSIDE AIR REGISTER OPENED.
8. This fireplace has provision for the installa-
tion of a gas pipe and is intended only for
connection to a decorative gas appliance
incorporating an automatic shutoff device
and complying with ANSI Z21.60-M96/CGA
2.26-M96, Standard for Decorative Gas Ap-
pliances for Installation in Solid-Fuel Burn-
ing Fireplaces (reference Clause 4.1.3 T).
9. ELITE ME43 fireplaces are sold with factory
installed doors. The outside combustion
air kit is mandatory and is included with the
fireplace. Optional blowers and decorative
trims are available.
Tools And Building Supplies Normally
Required
Tools:
Phillips screwdriver
Slot style screwdriver
Hammer
Saw and/or Sabersaw
Level
Measuring tape
Plumb line
Electric drill and bits
Pliers
Square
If gas pipe is used:
Pipe wrench
Pipe cutter
Pipe threader
Pipe joint compound
Pipe key valve
Building supplies:
2" x 3" or heavier lumber
Drywall panel or equivalent
Silicone caulking (non-combustible)
Overlay material for fireplace façade
Hearth extension (non-combustible)
PRECAUTIONS!
The most important areas of concern dealing
with the fireplace installation are clearances to
combustible materials, secure assembly of
components parts, the height of the chimney
system, the proper use of accessory equip-
ment and the techniques used in using finish-
ing materials applied to fireplace surrounds,
hearth extensions and wall coverings. Each of
these topics will be covered in greater detail
throughout this manual. Please give special
attention to these instructions as you progress
with your installation.
Fireplace Installation Procedure
1. Move the fireplace into the desired position
(follow the recommendations below for en-
closure).
2. Install the outside air assembly (or assem-
blies) - refer to page 7.
3. Install the enclosure surrounding the fire-
place (refer to the sections "Enclosure" be-
low and " Facing and Mantel" on page 6).
4. Install the hearth extension (see page 7).
Make sure the gap between the fireplace and
the hearth extension is sealed.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
LOCATING THE SECURITY FIREPLACE
Do not place the fireplace on carpeting, vinyl or
other soft surface floor coverings. It may,
however, be directly placed on flat wood, ply-
wood, particle board or other hard surface
materials.
ADJACENT WALL
A wall perpendicular to and in front of the
fireplace front facing must be at least 18" (460
mm) from the fireplace opening. A wall at 45º
to the front facing and starting at the fireplace's
outer edge is permitted. Projections within
this area are permitted. See Figure 4 .
WALL
FIREPLACE
45
18"
(460mm)
Figure 4

ENCLOSURE

WARNING: DO NOT PLACE LOOSE INSU-
LATION OR ANY OTHER MATERIAL IN
THE SPACE AROUND THE FIREPLACE OR
THE CHIMNEY. INSULATION PLACED ON
OR AROUND THE FIREPLACE OR CHIM-
NEY MAY CAUSE ADJACENT WOOD TO
OVERHEAT AND CATCH ON FIRE.
1. The fireplace must be installed against a
finished wall (like drywall finish). It must not
be installed against a vapor barrier or ex-
posed insulation ( see Figure 5 ).
2. Combustible materials like wood, plywood,
particle board or drywall can be in direct
contact with the fireplace standoffs. Two
inch (50 mm) clearance to combustibles
must be kept around the chimney.
STANDOFFS
OPENING
5