Precautions; Introduction; Clearances/Height Requirements; Chimney System - Superior BCF-3885 Installation Instructions Manual

PRECAUTIONS

Note: These fireplace systems are not difficult
to install. However, in the interest of safety, it is
recommended that the installer be a qualified or
certified "tradesman" familiar with commonly
accepted fireplace installation and safety tech-
niques as well as prevailing local codes.
The most important areas of concern dealing
with the installation of factory-built fireplaces are
clearances to combustible materials, proper as-
sembly of component parts, height of the chim-
ney system, the proper use of accessories sup-
plied by the manufacturer and the techniques
employed in using finishing materials applied to
the wall surrounding the fireplace, hearth exten-
sions and wall shields. Each of these topics will
be covered in thorough detail throughout this
manual. Please give each your special attention
as you progress with your installation.

INTRODUCTION

General Information
The BCF Series are wood-burning fireplaces fea-
turing a self-contained heat-circulating system.
A standard bar grate is also included to properly
position the fire. Outside combustion air kits,
decorative glass doors, forced air kits and the fan
adapter kit are available as optional equipment.
TYPICAL INSTALLATION
Chimney And
Termination
Forced Air Kit
(BCF Models Only)
Outside Combustion
Air Kit (Optional)
Figure 1
The BRF Series are conventional radiant-heat
fireplaces with a standard bar grate, optional
outside combustion air kits and optional deco-
rative glass doors.
Note: Illustrations shown reflect "typical" in-
stallations with nominal dimensions and are
for design and framing reference only. Actual
installations may vary due to individual design
preferences. However, always maintain mini-
mum clearances to combustible materials and
do not violate any specific installation require-
ments.
The BRF and BCF Series Fireplaces have been
tested and listed by Underwriters Laborato-
ries, Inc. (File No. MH8988-1/91) to the U.L.
127 standard for U.S. installations. These
units are intended for installation in residential
homes and other buildings of conventional
construction including commercial, not in mo-
bile homes.
These fireplace systems are designed for in-
stallation in accordance with the National Fire
Protection Standard for chimneys, fireplaces
and solid fuel burning appliances; NFPA 211
and in accordance with codes such as the
BOCA Basic/National Codes, the Standard Me-
chanical Code and the Uniform Building Codes.
Model BCF
(Shown)
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
WARNING: FAILURE TO USE MANUFAC-
TURE PROVIDED PARTS, VARIATIONS IN
TECHNIQUES AND CONSTRUCTION MA-
TERIALS OR PRACTICES OTHER THAN
THOSE DESCRIBED IN THIS MANUAL
MAY CREATE A FIRE HAZARD AND VOID
THE LIMITED WARRANTY.
The BCF and BRF systems consist of six basic
"sub-systems":
1. The Fireplace
2. The Chimney and Termination
3. The Optional Glass Doors
4. The Optional Forced Air Kits (BCF Series
only)
5. The Optional Combustion Air Kits
6. The Optional Collar Duct Kits
CLEARANCES AND HEIGHT
REQUIREMENTS
The fireplace may be placed on or near normal
construction materials*. The combustion air
kit, firestop spacer and roof flashing (not chase
flashings) may be placed directly on or against
normal construction materials.* The chimney
requires a minimum 2" air space to combus-
tibles ( See **Note ). A combustible mantle may
be installed 12" above the opening of the fire-
place as per NFPA 211, Section 7-2.3.3.
The fireplace and chimney system must be
enclosed when installed in or passing through
a living area where combustibles or people may
come in contact with it. This is important to
prevent possible personal injury or fire hazard.
For questions, please call your distributor or
the manufacturer. Special restrictions apply to
the front and facing of the fireplace and nearby
walls (See pages 16, 17 and 18 ).

CHIMNEY SYSTEM

These fireplaces are designed and code listed
for use with Security Chimneys FTF8 or FTF10
chimney System only. Always use Security
Chimneys FTF8 or FTF10 chimney components
with these fireplaces. Do not modify or alter
these components as this may cause a potential
serious hazard and void the Warranty.
*Construction Materials:
• framing materials • paneling
• particle board • flooring
• millboard • dry wall
• plywood • etc.
**Note: 1" clearance when installing FTF8 on
38" models or FTF10 on 43" models.
3