Technical Data; Bar And Chain Combinations - Husqvarna 359 Operation Manual

Technical data

Engine
Cylinder displacement, cu.in/cm
Cylinder bore, inch/mm
Stroke, inch/mm
Idle speed, rpm
Power, kW/ rpm
Ignition system
Manufacturer of ignition system
Type of ignition system
Spark plug
Electrode gap, inch/mm
Fuel and lubrication system
Manufacturer of carburetor
Carburetor type
Fuel tank capacity, US pint/litre
Oil pump capacity at 9,000 rpm, ml/min
Oil tank capacity, US pint/litre
Type of oil pump
Weight
Chain saw without bar or chain, empty tanks, lb/kg
Chain/bar
Standard bar length, inch/cm
Recommended bar lengths, inch/cm
Usable cutting length, inches/cm
Chain speed at max. power, m/sec
Pitch, inch/mm
Thickness of drive links, inch/mm
Number of teeth on drive sprocket
Recommended original and replacement bar and chain combinations
Following is a list of recommended cutting equipment for the Husqvarna chain saw models 357XP and 359. The combinations of
power head, bar and chain have been tested and found to be in accordance with the kickback and vibration requirements of ANSI
B 175.1–2000.
The guide bar nose radius is determined by either the maximum number of teeth in the nose sprocket or the corresponding
maximum nose radius of a hard nose.
The following list is the chain saw manufacturers recommendations. There may be other combinations available, which will also
achieve kickback reduction.
As we are listing the maximum guide bar nose radius, you may use a guide bar with smaller nose radius than in our list. For guide
bars of the same length, all sprocket-nose guide bars of the same pitch and having the same number of sprocket teeth may be
considered to have equivalent kickback energy. A hard nose bar having the same length and nose radius as a sprocket-nose bar
may be considered to have equivalent or less kickback energy than the sprocket-nose bar.

Bar and chain combinations

Chain saw models Husqvarna 357XP and 359 met the kickback performance requirements of ANSI B 175.1-2000 when tested
with the combinations of bars and saw chains listed below. The saw chain Husqvarna H30 is also classified as a low kickback saw
chain since it met the requirements for low kickback saw chain outlined in ANSI B 175.1-2000. We recommend to use only the
listed combinations of bars and chains for chain saw models Husqvarna 357XP and 359. Other chain saw models may not meet
the kickback requirements when equipped with the listed bar and chain combinations.
38 –
English
TECHNICAL DATA
357XP
3
3,45/56,5
1,81/46
1,34/34,0
2700
3,2/9600
SEM
CD
NGK BPMR 7A/Champion RCJ 7Y
0,02/0,5
Walbro
HDA 199/191
1,43/0,68
6-17
0,80/0,38
Automatic
12,1/5,5: 357 XP, 357 XP E-tech
12,3/5,6: 357 XPG, 357 XPG E-tech
15"/38
13-24"/33-61
12-23"/31-58
21,4
0,325/8,25
3/8" /9,52
0,050/1,3
0,058/1,5
7
359
3,60/59,0
1,85/47
1,34/34,0
2700
2,9/9000
SEM
CD
NGK BPMR 7A/Champion RCJ 7Y
0,02/0,5
Walbro
HDA 199/191
1,43/0,68
6-17
0,80/0,38
Automatic
12,1/5,5: 359, 359 E-tech
12,3/5,6: 359 G, 359 G E-tech
15"/38
13-24"/33-61
12-23"/31-58
20,0
0,325/8,25
3/8" /9,52
0,050/1,3
0,058/1,5
7