Table of Contents
Advertisement
Owner/Operator Manual
Manuel Du Propriétaire/Utilisateur
E10
The use of any gasoline exceeding 10% ethanol (E10) or
10% MTBE will void the product warranty.
L'utilisation d'une essence contenant plus de 10% d'éthanol
(E10) ou de 10% de MTBE annulent la garantie.
ENGLISH
FRANÇAIS
Path-Pro
938033 – SS21EC
®
Models
938030 – SS21
(SN 000101 +)
938031 – SS21
(SN 000101 +)
938032 – SS21E
(SN 000101 +)
(SN 000101 +)
938034 – SS21E
(SN 000101 +)
04535800A 6/13
Printed in USA
Advertisement
Table of Contents
Related Manuals for Ariens Path-Pro 136E
Summary of Contents for Ariens Path-Pro 136E
- Page 1 ® Path-Pro Owner/Operator Manual Manuel Du Propriétaire/Utilisateur Models 938030 – SS21 (SN 000101 +) 938031 – SS21 (SN 000101 +) 938032 – SS21E (SN 000101 +) 938033 – SS21EC (SN 000101 +) 938034 – SS21E (SN 000101 +) The use of any gasoline exceeding 10% ethanol (E10) or 10% MTBE will void the product warranty.
-
Page 2: Table Of Contents
Refer to this PRODUCT REGISTRATION manual for engine service recommendations. The Ariens dealer should register the product If the engine manual is not available, contact at the time of purchase. Registering the the engine manufacturer for a replacement product helps the company process warranty manual. - Page 3 If you do not understand or have difficulty following the instructions, contact your nearest Ariens Dealer for assistance. NOTE: To locate your nearest Ariens Dealer, go to www.ariens.com. WARNING: Improper assembly or adjustments can cause serious injury.
-
Page 4: Safety
SAFETY SIGNAL WORDS WARNING: This snow thrower is The safety alert symbols above and signal capable of crushing or amputating body parts. Failure to observe the words below are used on decals and in this safety instructions in the manuals manual. - Page 5 1. Safety Decal Identification 2. DANGER! Danger! ROTATING PARTS! ONLY use clean-out tool to clear blockages. NEVER use your hands. High speed auger/impeller rotates below discharge opening. Wait for all moving parts to stop before removing clogs or servicing. Figure 2 2.
-
Page 6: Rules For Safe Operation
Training 4. DANGER! Read, understand and follow all instructions on the machine and in the manual(s) before operating this unit. Be thoroughly familiar Danger! with the controls and the proper use of the equipment. Know how to stop the unit and disengage the controls quickly. - Page 7 Handle fuel with care; it is highly flammable. Thrown objects can cause injury. Check for weak spots on docks, ramps or floors. Avoid • Use an approved fuel container. uneven work areas and rough terrain. Stay • Never add fuel to a running engine or alert for hidden hazards.
-
Page 8: Maintenance And Storage
Do not operate in reverse unless absolutely Maintenance and Storage necessary. Always back up slowly and look down and behind before and while backing. Secure unit so it will not tip over during maintenance. Do not carry passengers. Before cleaning, removing clogs or making Disengage attachment drive when traveling any inspections, repairs, etc., disengage from one work area to another. -
Page 9: Slope Operation
Accessories Do not operate near drop-offs, ditches, or embankments. Unit can suddenly turn over if Use only Ariens Company-recommended a wheel is over the edge of a cliff or ditch, or attachments that are appropriate to your use if an edge caves in. -
Page 10: Controls And Features
CONTROLS AND FEATURES Figure 4 1. Handlebar 12. Oil Fill (Models 938031, 032, 033) 2. Auger Control Bar 13. Oil Drain Plug 3. Auger Control Cable Assembly 14. Fuel Cap & Tank 4. Remote Discharge Chute Handle 15. Choke Control Knob Assembly (Model 938033) 16. -
Page 11: Operation
OPERATION CONTROLS AND FEATURES Fuel Shut-off Valve (Item 20) IMPORTANT: The fuel shut-off valve MUST WARNING: AVOID INJURY. be in the closed (off) position before Read and understand the entire transporting the unit. The valve is closed Safety section before proceeding. when it is narrow and vertical when viewed from above. -
Page 12: Engine Oil
Remote Discharge Chute Handle regulations, that will only function properly when the fuel tank has been filled to the Assembly recommended level. Overfilling may cause (Item 4) permanent damage to evaporative emissions Model 938033 control system components. Filling to the Move remote discharge chute handle forward recommended level ensures a vapor gap or backward to control direction of snow... -
Page 13: Start Engine
3. Check oil level on dipstick. Oil level must 10. Pull auger control bar (Item 2) back to be maintained at safe operating level. handlebar to start auger; release bar to See SPECIFICATIONS on page 20. See stop auger. Engine Manual for detailed information. Start Engine (Electric Start) 4. - Page 14 Remote Discharge Chute Handle 1. Move engine switch (Item 16) to OFF position and remove key. Allow unit to Assembly cool. (Item 4) 2. Tip unit back onto engine guard. Do not Model 938033 tip further than engine guard allows or oil IMPORTANT: Always throw snow in a safe may leak out of engine.
- Page 15 Adjust Auger Cable 1. Move engine switch (Item 16) to OFF position and remove key. Allow unit to cool. 2. Slide plastic sleeve up to auger control bar. 3. Insert Z-hook into appropriate hole in adjustment bracket. When auger control bar is disengaged, there should minor slack in cable and no tension.
- Page 16 Adjust Remote Chute Rotation Cables Model 938033 1. Move engine switch (Item 16) to OFF position and remove key. Allow unit to cool. 2. Open fuel and oil door (Item 22) to access chute rotation cable adjustment screws. 3. Loosen chute rotation cable adjustment screws.
-
Page 17: Maintenance Schedule
MAINTENANCE SCHEDULE IMPORTANT: Proper maintenance can WARNING: AVOID INJURY. Read prolong the life of unit. The following chart and understand the entire Safety shows the recommended service schedule. section before proceeding. Interval Task Action Clean unit. Remove snow and debris with a soft-bristled brush. -
Page 18: Storage
Follow the recommended mix ratio found on the fuel stabilizer container. To treat the fuel system for storage: 1. Add fuel stabilizer (Ariens part number 00592900) according to manufacturer’s instructions. 2. Run engine for at least 10 minutes after adding stabilizer to allow it to reach the carburetor. -
Page 19: Troubleshooting
DO NOT use your hands. Auger paddles are worn Replace auger paddles. See Replace Auger or damaged. Paddles on page 14 or see your Ariens Dealer. Remote Remote chute rotation Adjust remote chute rotation cables. See Adjust discharge chute cables are loose. -
Page 20: Service Parts
SERVICE PARTS ACCESSORIES See your authorized Ariens dealer for See your authorized Ariens dealer to add genuine OEM service parts. these optional accessories to your unit. Part No. Description Part No. Description 00592900 Fuel Stabilizer (4 oz) 73801100 Sno-Thro Cover Kit... -
Page 21: Warranty
® ® Sno-Thro , Sno-Tek Chore Performing Equipment Limited Warranty Ariens Company (Ariens) warrants to the original purchaser that Ariens, Gravely, Parker, and Countax ® ® brand chore performing equipment (including Sno-Thro and Sno-Tek equipment) purchased on or after 1/1/2013 will be free from defects in material and workmanship for the time period noted in the chart below. -
Page 22: Customer Responsibilities
Register the product immediately at the time of sale. If the dealer does not register the product, the customer must complete the product registration card in the literature package and return it to Ariens Company, or register the unit online at www.ariens.com, www.gravely.com, www.countax.com or www.parkersweeper.com. - Page 23 Exclusions – Items Not Covered by This Warranty • Parts that are not genuine Ariens, Gravely, Parker or Countax service parts are not covered by this warranty and may void the warranty. • Damages resulting from the installation or use of any part, accessory, or attachment which is not approved by the Ariens Company for use with product(s) identified herein are not covered by this warranty.
- Page 24 Ariens 655 West Ryan Street Brillion, WI 54110 920-756-4688 www.ariens.com...