Advertisement
U S E R ' S G U I D E
15) When the H2O Mop stops emitting steam, this will occur after approximately 20 minutes of use, turn off the
H2O Mop and simply refill the Water Tank using the Measuring Cup, and then again turn on and continue cleaning.
WARNING: NEVER run the H2O Mop without water. NEVER direct steam at any person or animal.
Use the H2O Mop on sealed hard floor only.
Prior to use, insert the Power Cord into the Upper Cord
Holder on the H2O Mop (as illustrated in fig. 1.)
16) When you finish your cleaning, unplug Power Cord from
outlet, empty the Water Tank, carefully remove the Cloth Pad
f rom the head, wind Power Cord around the Upper Cord Wr a p
first then go around the Lower Cord Wrap and so on. This will
p rotect the Power Cord from damage due to twisting.
Note: if you go around the Lower Cord Wrap first you will
expose the cord to unnecessary and harmful twisting which can
damage the cord. Store H2O Mop upright in a dry area or hang
by the Carry Handle.
C A U T I O N : The Cloth Pad may be very hot. Not for space heating purpose.
CLEANING AND MAINTENANCE
CAUTION: Prior to cleaning or maintenance isolate the unit by removing the cord from the power socket.
Do not immerse the unit in water.
1) Microfiber Cloth Pad can be machine washed in hot water.
2) Wipe the steamer with a soft cloth.
The H2O Mop should only be used with its own specially developed floor cloths and Filter (spare Cloth Pads and
Filters are available from your retailer).
Cleaning procedure to remove limescale
If your H2O Mop begins to produce steam more slowly than usual or stops producing
steam you may need to remove limescale. Limescale can develop over time on the
metal parts and greatly affect mop's performance. We recommend removing limescale
on regular basis especially in areas with hard water. The frequency of limescale
removal depends upon the hardness of your tap water and how often you use the
steam mop.
To remove limescale from the H2O mop please follow these procedures:
By using Scraper
1) Make sure that the H2O Mop is disconnected from the power supply before
maintenance.
2) Remove the mop head from the main body, as illustrated in Fig 2.
fig. 2.
fig. 3.
7
U S E R ' S G U I D E
Thank you and congratulations for choosing the H2O Mop. The H2O Mop is a new way of cleaning that is
effective and far more hygienic than conventional methods. The H2O Mop achieves a high degree of hygienic and
increasing cleansing power by converting water into steam using a microfiber floor cloth enhancing absorbency.
When contact is made with floor surfaces, dirt and grime can be eliminated in a matter of seconds. Since the
H2O Mop uses the active power of steam without the use of detergents or soap, it is environmentally friendly.
fig. 1.
When used correctly the H2O Mop can kill dust mites and some types of bacteria. To disinfect a specific area,
position the steamer over the area for a minimum of eight seconds. The steam temperature will reach to
approximately 90-100°C (194-212°F). Use this procedure to disinfect floors in bathrooms, showers, around
kitchen counters, pet sleeping quarters, etc.
INSTRUCTIONS FOR USE
The H2O Mop is designed to thoroughly clean floor surfaces, such as marble, ceramic, stone, linoleum, sealed
h a rdwood floors and sealed parquet.
WA R N I N G : On surfaces that have been treated with wax, the wax may be removed by the heat and steam action.
Do not use on unsealed wood floors or let unit stand on any wood floor for an extended period of time. This could
cause the wood grain to rise. When using on vinyl, linoleum or any other heat sensitive floors, use extra caution.
Too much heat can melt down glue in the flooring. It is there f o re recommended that a sample cleansing be carr i e d
out on an isolated area of the floor. It is also recommended that you check the use and care instructions of the
s u rface from the floor manufacturer to ensure suitability to steam cleaning.
H20 Mop uses tap water. Residents in areas with hard water, should use distilled water for better perf o rm a n c e .
HOW TO ASSEMBLE AND USE
1 ) Attach head to body.
2 ) S e c u re head with the small Philips Head Screw until it is fully tightened.
4
Hide quick links:
Advertisement
