Table of Contents
Advertisement
Installation
Instructions
"If you have questions, Call 800-GE-CARES
www.GEAppliances.com"
Skill Level: High
Completion Time: 1 to 3 Hours
Proper installation is the responsibility of the installer. Product failure due to improper installation
is not covered under the GE Appliance Warranty. See the Owners Manual for warranty
information.
CAUTION: Before you begin
Read these instructions carefully and
completely.
• IMPORTANT- Save these instructions for
local inspector's use.
• IMPORTANT- Observe all governing codes
and ordinances.
Parts Included
Anti-Tip Bracket and leg leveler
Tools You Will Need
Adjustable wrench
1/4"Nut
driver
Level
Pub. No. 31-10463
4053P447-3
229C
Self Cleaning Free-Standing
Electric Range
EER2000, EER3000 JBP24, JBP26, JBP30, JBP35, JBP48, JBP64, JBP65,
JBP66, JBP67, JBP70, JBP78, JBP79, JBP85, JB940, JB960, JB965
Average
Low
Drill with
1/8" Bit
Phillips
Screwdriver
• NOTE TO INSTALLER- Be sure to leave
these instructions with the consumer.
• OWNER- Keep these instructions for future
reference.
• WARNING- This appliance must be
properly grounded.
Materials Needed
Lag Bolts Anchor Sleeves
(For Concrete Floors Only)
y
Pencil
y y
5/16" Hex Head
Nut driver
1
or visit our website at:
( UL Approved 40 AMP)
3 -Wire Cord
4- Wire Cord
OR
4'long
4'long
Safety
Glasses
Tape Measure
Flat-Bladed
Screwdriver
Advertisement
Table of Contents
Related Manuals for GE 229C4053P447-3 1
Summary of Contents for GE 229C4053P447-3 1
-
Page 1: Installation Instructions
Average Completion Time: 1 to 3 Hours Proper installation is the responsibility of the installer. Product failure due to improper installation is not covered under the GE Appliance Warranty. See the Owners Manual for warranty information. CAUTION: Before you begin Read these instructions carefully and completely. -
Page 2: Important Safety Instructions
• Install anti-tip bracket packed with range • See Installation Instructions If you pull the range out and away from the wall for any reason, make sure the Anti-Tip bracket is engaged when the range is pushed back against the wall. -
Page 3: Pre-Installation Checklist
Place hands on both sides of the door. As you close the door, lift up and away from the range. Lift door up until the hinges clear the slots. EASY INSTALLATION OF YOUR NEW FREE-STANDING RANGE Before you begin-Read these instructions completely and carefully. - Page 4 Installation Instructions Installation Required Clearances See Ilustrations below for all rough-in and spacing dimensions. The range may be placed with 0” clearance (flush) at the back wall and side walls of the cabinet. MINIMUM DIMENSIONS BETWEEN COOKTOP, WALLS, AND ABOVE THE COOKTOP.
-
Page 5: Electrical Connections
Failure to wire your oven according to governing codes could result in a hazardous condition. If there are no local codes, your range must be wired and fused to meet the requirements of the National Electrical Code, ANSI/NFPA No. 70-Latest Edition. You can... - Page 6 Installation Instructions Electrical Connections NEW CONSTRUCTION AND FOUR WIRE CORD CONNECTION KIT B3 Complete 4 wire 3 Screws cord kit. Below are step by step instructions on how to install the kit. Remove the screws on the terminal block with a 1/4”...
- Page 7 Installation Instructions Electrical Connections THREE- WIRE CORD CONNECTION KIT Complete 3 Screws wire cord kit. Below are step by step instructions on how to install the kit. B4a Remove the screws on the terminal block with a 1/4” nut driver or phillips screwdriver.
- Page 8 Decide whether the bracket will be installed on the right or left side of range location. b. If the bracket side of the range has an adjacent cabinet, place the bracket against the back wall and cabinet as shown in Fig. 1. If there is a countertop overhang, offset the bracket by the amount of overhang.
-
Page 9: Storage Drawer Removal
Anti-Tip Bracket. Level the Range The range must be level for proper cooking and baking. D5 Install the oven racks.(See Owner’s Manual for instructions.) Put a spirit level or a glass... - Page 10 Installation Instructions Installing the Range Replacing the Storage Drawer Place the drawer rail on the guides. Push the drawer in until it stops. Lift the front of the drawer and push in until the stops clear the guides. Lower the front of the drawer and push in until it closes.
-
Page 11: Final Check List
60 seconds. Turn the knob off when glow is detected. If the glow is not detected within the time limit, recheck the range wiring connections. If change is required, retest again. If no change is required, have building wiring checked for proper connections... - Page 12 NOTES Pub. No. 31-10463 4053P447-3 229C...