Download
Share
Print this page
  1. Manuals
  2. Brands
  3. HP Manuals
  4. Software
  5. Surestore Tape Library Model 10/180
  6. Manual

HP Surestore Tape Library Model 10/180 Manual

Installing the web-based library administrator
Hide thumbs Also See for Surestore Tape Library Model 10/180:

Advertisement

Quick Links

Download this manual See also: Configuration Manual, Manual
Installing the Web-Based Library Administrator
Requirements
Procedures
313670504 (Rev D)
Before installing the Web-Based Library Administrator,
verify that the following requirements are met:
• Library is powered on and initialized
• Minimum requirements: 200MHz processor; 64 MB
RAM (96 MB RAM is preferred)
• Microcode level 3.01 or later is loaded.
Microcode level 3.01 contains the Web-Based Library
Administrator software.
• Java™ Plug-in Software 1.4 or later
You can download the Java plug-in from:
http://java.sun.com/products/plugin
• Netscape Navigator 4.5 or later or Internet Explorer 4.0
or later with the latest Service Pack
The following steps must be performed in the order in
which they are presented to successfully install the
Web-Based Library Administrator.
Note: You must know the IP Address of your library before
you perform the following steps.
1

Advertisement

loading

Related Manuals for HP Surestore Tape Library Model 10/180

Summary of Contents for HP Surestore Tape Library Model 10/180

  • Page 1 Installing the Web-Based Library Administrator Requirements Before installing the Web-Based Library Administrator, verify that the following requirements are met: • Library is powered on and initialized • Minimum requirements: 200MHz processor; 64 MB RAM (96 MB RAM is preferred) • Microcode level 3.01 or later is loaded. Microcode level 3.01 contains the Web-Based Library Administrator software.
  • Page 2 Step 1 Ensure the library is powered on and initialized. Step 2 Connect your Ethernet cable to the ENET connector on the electronics module bulkhead. This allows you to communicate with the Web-Based Library Administrator. See Figures 1 and 2 for the connection diagram. Step 3 Set up your Internet Protocol (IP) Address from the Operator Panel.
  • Page 3 You need to ask your System Administrator for this number. a. Press MENU. The NETWORK CONFIG MENU is displayed. b. Arrow to SUBNET MASK and press SELECT. An edit window is displayed. Follow the directions on the Operator Panel for entering and saving data.
  • Page 4 d. Perform a reset to save the changes. Step 6 Set up your Network Gateway from the Operator Panel. This allows you to link to different networks. You need to ask your System Administrator for this number. a. Press MENU. The NETWORK CONFIG MENU is displayed.
  • Page 5 b. Write down the policy name and click OK if an error dialog box is displayed stating it “Could not find the Policy File”. This policy name is used later in this procedure. Add the Policy: a. Click Add Policy Entry button. The Policy Entry window is displayed.
  • Page 6 The Policy Entry window is displayed with the information you entered. h. Click Done. The Policy Tool window is displayed with the CodeBase you entered. i. Save the new policy name to disk by selecting one of the following: - If an error dialog box was displayed when you launched the Policy Tool: 1.
  • Page 7 Step 8 Perform a ping to ensure the IP Address is correct. To do this in Windows: a. Go to the Windows Start Menu. b. Select Start -> Run. c. Enter ping <library name or IP Address> in the Start->Run text field. To do this in UNIX: –...
  • Page 8 C24421 Figure 1 10/180 Tape Library 1. Enet (Ethernet connection) 313670504 (Rev D)
  • Page 9 C 24422 Figure 2 20/700 Tape Library 1. Enet (Ethernet connection) 313670504 (Rev D)
  • Page 10 313670504 (Rev D)

This manual is also suitable for:

Surestore tape library model 20/700Web-based library administrator