Yamaha MOXF6 Manual page 101

[3] TEMPO PHASER
No. Parameter
1 LFO Speed 16th – 4thx16
2 LFO Depth 0 – 127
3 Phase Shift Offset 0 – 127
4 Feedback Level -63 – +63
5 LFO Phase Reset Off (free run), Key On Reset,
SEQ Start Reset
6 – 9: Same as the parameters shaded in gray in CROSS DELAY on page 98.
10 Dry/Wet Balance D63>W – D=W – D<W63
11 Stage 4 – 22
12 Diffusion Mono, Stereo
13 —
14 —
15 —
16 —
[4] DYNAMIC PHASER
No. Parameter
1 Sensitivity 0 – 127
2 Dyna Level Offset 0 – 127
3 Feedback Level -63 – +63
4 Attack Time 0.3ms – 227ms
5 Release Time 2.6ms – 2171ms
6 Release Curve 0 – 127
7 Direction Up, Down
8 Dyna Threshold Level 0 – 127
9 —
10 Dry/Wet Balance D63>W – D=W – D<W63
11 Stage 4, 5, 6
12 —
13 – 16: Same as the parameters shaded in gray in CROSS DELAY on page 98.
Category — TREMOLO&ROTARY
[1] AUTO PAN
No. Parameter
1 LFO Speed 0.0Hz – 39.70Hz
2 L/R Depth 0 – 127
3 F/R Depth 0 – 127
4 PAN Direction L<>R, L>>R, L<<R, Lturn,
Rturn, L/R
5 LFO Wave 0 – 28
6 – 9: Same as the parameters shaded in gray in CROSS DELAY on page 98.
10 —
11 EQ Mid Frequency 100Hz – 10.0kHz
12 EQ Mid Gain -12dB – +12dB
13 EQ Mid Width 0.1 – 12.0
14 —
15 Input Mode Mono, Stereo
16 —
[2] TREMOLO
No. Parameter
1 LFO Speed 0.0Hz – 39.70Hz
2 AM Depth 0 – 127
3 PM Depth 0 – 127
4 —
5 —
6 – 9: Same as the parameters shaded in gray in CROSS DELAY on page 98.
10 —
11 EQ Mid Frequency 100Hz – 10.0kHz
12 EQ Mid Gain -12dB – +12dB
13 EQ Mid Width 0.1 – 12.0
14 LFO Phase difference -180deg – +180deg
15 Input Mode Mono, Stereo
16 —
Range Value Table No.
(5 – 29) 13
(0 – 127)
(0 – 127)
(1 – 127)
(0 – 2)
(1 – 127)
(4 – 22)
(0 – 1)
Range Value Table No.
(0 – 127)
(0 – 127)
(1 – 127)
(0 – 127) 15
(0 – 127) 16
(0 – 127)
(0 – 1)
(0 – 127)
(1 – 127)
(4 – 6)
Range Value Table No.
(0 – 127) 1
(0 – 127)
(0 – 127)
(0 – 5)
(0 – 28)
(14 – 54) 3
(52 – 76)
(1 – 120)
(0 – 1)
Range Value Table No.
(0 – 127) 1
(0 – 127)
(0 – 127)
(14 – 54) 3
(52 – 76)
(1 – 120)
(4 – 124)
(0 – 1)
[3] ROTARY SPEAKER
No. Parameter
1 Rotor Speed Slow 0.0Hz – 2.65Hz
2 Horn Speed Slow 0.0Hz – 2.65Hz
3 Rotor Speed Fast 0.0Hz – 39.70Hz
4 Horn Speed Fast 0.0Hz – 39.70Hz
5 Slow-Fast Time of Rotor 0 – 127
6 Slow-Fast Time of Horn 0 – 127
7 Drive Rotor 0 – 127
8 Drive Horn 0 – 127
9 Rotor/Horn Balance R63>H – R=H – R<H63
10 —
11 – 14: Same as the parameters shaded in gray in CROSS DELAY on page 98.
15 Mic L-R Angle 0deg – 180deg
16 Speed Control Slow, Fast
Category — DISTORTION
[1] AMP SIMULATOR 1
No. Parameter
1 Overdrive 0 – 100%
2 Device Transistor, Vintage Tube,
Distortion 1, Distortion 2,
Fuzz
3 Speaker Type Flat, Stack, Combo, Twin,
Radio, Megaphone
4 Presence -10 – 10
5 Output Level 0 – 100%
6 —
7 —
8 —
9 —
10 Dry/Wet Balance D63>W _ D=W _ D<W63
11 —
12 —
13 —
14 —
15 —
16 —
[2] AMP SIMULATOR 2
No. Parameter
1 Overdrive 0 – 127
2 AMP Type Off, Stack, Combo, Tube,
Crunch, Hi Gain, British
3 LPF Cutoff Frequency 1.0kHz – 20.0kHz
4 Output Level 0 – 127
5 —
6 —
7 —
8 —
9 —
10 Dry/Wet Balance D63>W – D=W – D<W63
11 —
12 —
13 —
14 —
15 —
16 —
[3] COMP DISTORTION
No. Parameter
1 Overdrive 0 – 127
2 EQ Low Frequency 32Hz – 2.0kHz
3 EQ Low Gain -12dB – +12dB
4 LPF Cutoff Frequency 1.0kHz – 20.0kHz
5 Output Level 0 – 127
6 —
7 EQ Mid Frequency 100Hz – 10.0kHz
8 EQ Mid Gain -12dB – +12dB
9 EQ Mid Width 0.1 – 12.0
10 Dry / Wet Balance D63>W – D=W – D<W63
11 Edge 0 – 127
12 Attack 1ms – 40ms
13 Release 10ms – 680ms
14 Threshold -48dB – -6dB
15 Ratio 1 – 20.0
16 —
Effect Parameter List
Range Value Table No.
(0 – 63) 1
(0 – 63) 1
(64 – 127) 1
(64 – 127) 1
(0 – 127)
(0 – 127)
(0 – 127)
(0 – 127)
(1 – 127)
(0 – 60)
(0 – 1)
Range Value Table No.
(0 – 100)
(0 – 4)
(0 – 5)
(0 – 20)
(0 – 100)
(1 – 127)
Range Value Table No.
(0 – 127)
(0 – 6)
(34 – 60) 3
(0 – 127)
(1 – 127)
Range Value Table No.
(0 – 127)
(4 – 40) 3
(52 – 76)
(34 – 60) 3
(0 – 127)
(14 – 54) 3
(52 – 76)
(1 – 120)
(1 – 127)
(0 – 127)
(0 – 19) 8
(0 – 15) 9
(79 – 121)
(0 – 7) 10
MOXF6/MOXF8 Data List
101