Yamaha MOXF6 Manual page 100

[4] SYMPHONIC
No. Parameter
1 LFO Speed 0.0Hz – 39.70Hz
2 LFO Depth 0 – 127
3 Delay Offset 0.0ms – 50.0ms
4 —
5 —
6 – 9: Same as the parameters shaded in gray in CROSS DELAY on page 98.
10 Dry/Wet Balance D63>W – D=W – D<W63
11 EQ Mid Frequency 100Hz – 10.0kHz
12 EQ Mid Gain -12dB – +12dB
13 EQ Mid Width 0.1 – 12.0
14 —
15 —
16 —
[5] ENSEMBLE DETUNE
No. Parameter
1 Detune -50cent – +50cent
2 Initial Delay Lch 0.0ms – 50.0ms
3 Initial Delay Rch 0.0ms – 50.0ms
4 Spread 0 – 63
5 —
6 —
7 —
8 —
9 —
10 Dry/Wet Balance D63>W – D=W – D<W63
11 – 14: Same as the parameters shaded in gray in CROSS DELAY on page 98.
15 —
16 —
Category — FLANGER
[1] VCM FLANGER
No. Parameter
1 Speed 0.040Hz – 10.00Hz
2 Manual 0 – 127
3 Depth 0 – 127
4 Feedback 0 – 127
5 Type 1 – 3
6 Spread 0 – 127
7 Mix 0 – 127
8 —
9 —
10 —
11 —
12 —
13 —
14 —
15 —
16 —
[2] CLASSIC FLANGER
No. Parameter
1 LFO Speed 0.0Hz – 39.70Hz
2 LFO Depth 0 – 127
3 LFO Wave Triangle, Sine, Random
4 Delay Offset 0.09 – 36.21ms
5 Feedback Level -100 – +100%
6 – 9: Same as the parameters shaded in gray in CROSS DELAY on page 98.
10 Dry/Wet Balance D63>W – D=W – D<W63
11 EQ Mid Frequency 100Hz – 10.0kHz
12 EQ Mid Gain -12dB – +12dB
13 EQ Mid Width 0.1 – 12.0
14 Modulation Phase -180 – +180
15 Feedback High Damp 0.1 – 1.0
16 Analog Feel 0 – 10
Range Value Table No.
(0 – 127) 1
(0 – 127)
(0 – 127) 2
(1 – 127)
(14 – 54) 3
(52 – 76)
(1 – 120)
Range Value Table No.
(14 – 114)
(0 – 127) 2
(0 – 127) 2
(0 – 63)
(1 – 127)
Range Value Table No.
(0 – 235) 20
(0 – 127)
(0 – 127)
(0 – 127)
(0 – 2)
(0 – 127)
(0 – 127)
Range Value Table No.
(0 – 127) 1
(0 – 127)
(0 – 2)
(0 – 139) 18
(0 – 200)
(1 – 127)
(14 – 54) 3
(52 – 76)
(1 – 120)
(0 – 16) 19
(1 – 10)
(0 – 10)
[3] TEMPO FLANGER
No. Parameter
1 LFO Speed 16th – 4thx16
2 LFO Depth 0 – 127
3 Feedback Level -63 – +63
4 Delay Offset 0.0ms – 50.0ms
5 LFO Phase Reset Off (free run), Key On Reset,
SEQ Start Reset
6 – 9: Same as the parameters shaded in gray in CROSS DELAY on page 98.
10 Dry/Wet Balance D63>W – D=W – D<W63
11 EQ Mid Frequency 100Hz – 10.0kHz
12 EQ Mid Gain -12dB – +12dB
13 EQ Mid Width 0.1 – 12.0
14 LFO Phase Difference -180deg – +180deg
15 —
16 —
[4] DYNAMIC FLANGER
No. Parameter
1 Sensitivity 0 – 127
2 Delay Offset 0 – 127
3 Feedback Level -63 – +63
4 Attack Time 0.3ms – 227ms
5 Release Time 2.6ms – 2171ms
6 Release Curve 0 – 127
7 Direction Up, Down
8 Dyna Threshold Level 0 – 127
9 Dyna Level Offset 0 – 127
10 Dry/Wet Balance D63>W – D=W – D<W63
11 —
12 —
13 – 16: Same as the parameters shaded in gray in CROSS DELAY on page 98.
Category — PHASER
[1] VCM PHASER MONO
No. Parameter
1 Speed 0.100Hz – 10.00Hz
2 Manual 0 – 127
3 Depth 0 – 127
4 Feedback 0 – 127
5 Stage 4, 6, 8, 10, 12, 16
6 Mode 1, 2, 3
7 Color 0 – 127
8 —
9 —
10 —
11 —
12 —
13 —
14 —
15 —
16 —
The Color parameter is not available in the following conditions: When Mode is set to 1 and Stage
is set to 4, 6, 8. 12 or 16; or when Mode is set to 2 and Stage is set to 4 or 10.
[2] VCM PHASER STEREO
No. Parameter
1 Speed 0.100Hz – 10.00Hz
2 Manual 0 – 127
3 Depth 0 – 127
4 Feedback 0 – 127
5 Stage 4, 6, 8, 10
6 Mode 1, 2
7 Color 0 – 127
8 Spread 0 – 127
9 —
10 —
11 —
12 —
13 —
14 —
15 —
16 —
The Color parameter is not available in the following conditions: When Mode is set to 1 and Stage
is set to 4, 6, or 8; or when Mode is set to 2 and Stage is set to 4 or 10.
Effect Parameter List
Range Value Table No.
(5 – 29) 13
(0 – 127)
(1 – 127)
(0 – 127) 2
(0 – 2)
(1 – 127)
(14 – 54) 3
(52 – 76)
(1 – 120)
(4 – 124)
Range Value Table No.
(0 – 127)
(0 – 127)
(1 – 127)
(0 – 127) 15
(0 – 127) 16
(0 – 127)
(0 – 1)
(0 – 127)
(0 – 127)
(1 – 127)
Range Value Table No.
(0 – 252) 21
(0 – 127)
(0 – 127)
(0 – 127)
(0 – 5)
(0 – 2)
(0 – 127)
Range Value Table No.
(0 – 252) 21
(0 – 127)
(0 – 127)
(0 – 127)
(0 – 3)
(0 – 1)
(0 – 127)
(0 – 127)
MOXF6/MOXF8 Data List
100