Vivotek PT8133 Quick Installation Manual
Vivotek PT8133 Quick Installation Manual

Vivotek PT8133 Quick Installation Manual

1mp poe, wps 802.11n
Hide thumbs Also See for PT8133:

Advertisement

Quick Links

PT8133/33W
Quick Installation Guide
繁中
簡中
日本語
English
PT8133:
1MP • PoE
PT8133W:
1MP • WPS • 802.11n
Deutsch
Français
Español
Português
Русский
Italiano
Türkçe
Polski
Česky
Svenska

Advertisement

Table of Contents
loading

Summary of Contents for Vivotek PT8133

  • Page 1 PT8133/33W Quick Installation Guide Русский Česky Svenska 繁中 簡中 日本語 Deutsch Italiano Türkçe English Français Español Português Polski PT8133: 1MP • PoE PT8133W: 1MP • WPS • 802.11n...
  • Page 2 Warning Before Installation Power off the Network Camera as Keep the Network Camera soon as smoke or unusual odors away from water. If the Network are detected. Camera becomes wet, power off immediately. Contact your distributor in the event of Contact your distributor in the event of occurrence.
  • Page 3 Do not place the Network Camera Do not touch the Network Camera on unsteady surfaces. during a lightning storm. Do not disassemble the Network Do not drop the Network Camera. Camera. Do not insert sharp or tiny objects Do not manually pan and tilt the into the Network Camera.
  • Page 4: Package Contents

    Package Contents PT8133/33W Power Adapter Antenna Screws (PT8133W Only) Quick Installation Guide / Software CD Warranty Card Mount kit & Foot Pads EN - 3...
  • Page 5: Physical Description

    Physical Description Front Panel Lens and Manual Focus Ring Antenna Status LEDs Item LED status Description Steady Red Power on and system boot Red LED off Power off Blink Green every 1 sec. + Steady Red Network connected (heartbeat) Green LED off + Steady Red Network failed Blink Red every 0.15 sec.
  • Page 6: Hardware Installation

    Hardware Installation Mounting the Network Camera - Ceiling Mount 1. Use the holes on the mount bracket as a template to mark where holes will be drilled on the ceiling. Drill two holes into the ceiling; and hammer in the plastic anchors. 2.
  • Page 7 Mounting the Network Camera - Wall Mount 1. Use the holes on the mount bracket as a template to mark where holes will be drilled on the ceiling. Drill two holes into the wall; and hammer in the plastic anchors. 2.
  • Page 8: General Connection (Without Poe)

    Network Deployment General Connection (without PoE) 1. Connect the camera to a switch via Ethernet cable. 2. Connect the supplied power adapter between the camera and a power outlet. Ethernet Switch NOTE: The PT8133W comes with an antenna. It should be installed by turning clockwise to attach to the associated connector.
  • Page 9: Power Over Ethernet (Poe)

    Power over Ethernet (PoE) When using a PoE-enabled switch The PT8133 Network Camera is PoE-compliant, allowing transmission of power and data via a single Ethernet cable. Follow the below illustration to connect the camera to a PoE enabled switch via a CAT5e Ethernet cable.
  • Page 10: Assigning An Ip Address

    “Next” button to continue the program. Installation Wizard 2 3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network Cameras on the same LAN. 4. After a brief search, the main installer window will pop up. Double-click on the MAC address that matches the one printed on the camera label or the S/N number on the package box label to open a browser management session with the Network Camera.
  • Page 11: Ready To Use

    Ready to Use 1. A browser session with the Network Camera should prompt as shown below. 2. You should be able to see live video from your camera. You may also install the 32-channel recording software from the software CD in a deployment consisting of multiple cameras.
  • Page 12 Configure the Wireless Connection (PT8133W) 1. Make sure your AP (Access Point) and Operating System support the WPS (Wi-Fi Protected Setup) functions. WPS enables easy setup with compatible APs. 2. Connect your camera using a LAN cable, open a web console, and enter the Configuration ->...
  • Page 13 NOTE: 1. WPS may not work if your AP is configured with a "hidden" SSID. 2. If the camera can not detect an AP after 2 minutes, the wireless setup will be cancelled. 3. If a camera is assigned with a fixed IP outside the AP's network segment, wireless setup will fail.
  • Page 14 All specifications are subject to change without notice. Copyright 2011 VIVOTEK INC. All rights reserved. P/N:625016400G VIVOTEK INC. VIVOTEK USA, INC. 6F, No.192, Lien-Cheng Rd., Chung-Ho, New Taipei City, 235, Taiwan, R.O.C. 2050 Ringwood Avenue, San Jose, CA 95131 |T: +886-2-82455282| F: +886-2-82455532| E: sales@vivotek.com...

This manual is also suitable for:

Pt8133w

Table of Contents