Ford Edge Quick Reference Manual page 8

FUnCTiOn
REARvIEw CAmERA* blInd Spot InfoRmAtIon
This system provides a visual display of the area SyStEm (blIS
behind the vehicle. The display automatically
tRAffIC AlERt (CtA)*
appears in the touch screen when the vehicle is
bliS uses radar sensors to help you determine
in R (Reverse) and uses green, yellow and red
if a vehicle may be in your blind spot zone. The
guides to alert you of your proximity to objects.
CTA feature alerts you if a car is coming toward
For non-touch screen vehicles, the image will
you when you are backing out of a parking
appear in the 4.2 inch center stack display.
space. bliS and CTA will display a yellow
indicator light in your exterior mirrors and the
CTA will also sound tones and display messages
to warn you which direction vehicles are
approaching. Refer to the Driving Aids chapter
in your Owner's Manual for more information.
SElECtShIft AUtomAtIC™
tRAnSmISSIon*
Gives you the ability to manually change gears if
REvERSE SEnSIng SyStEm
you'd like. To use, move the gearshift lever from
This system sounds a warning tone if there is an
D (Drive) to S (Sport). Then, simply press + or –
obstacle near the vehicle's rear bumper when
buttons on the gearshift lever to make shifts. if
the vehicle is in R (Reverse) and is traveling
equipped with steering wheel paddles, pull the
less than 3 mph (5 km/h). The warning tone will
right paddle (+) to upshift, pull the left paddle
increase in frequency as the object gets closer.
(–) to downshift.
note: visibility aids do not replace the need to
watch where the vehicle is moving. Refer to your
Owner's Manual for safety information, more
detail and limitations.
14
myKEy *
®
) wIth CRoSS MyKey allows you to program certain driving
®
restrictions in order to promote good driving
habits. You can program things like; speed
restrictions, limited volume levels and safety belt
reminders. For complete information, refer to the
MyKey chapter in your Owner's Manual.
SECURICodE™ KEylESS
EntRy SyStEm*
Allows you to lock or unlock the doors using the
touchpad. You will need your five digit factory
code located on your owner's wallet card in the
glove box. Refer to the Locks chapter in your
Owner's Manual for more information on how
to use SecuriCode.
COMFORT
*
(if equipped)
hEATED FROnT SEATS
To access heated seats, press the Climate
corner on your touch screen. Press
repeatedly to cycle through the various heat
modes and off. if your vehicle is not equipped
with a touch screen, press the hard button
EASYFOlD ® REAR
FOlDinG SEATS*
The controls are located near the left side
of the liftgate interior opening. Press the top
control to lower the right seat, or the bottom
control to lower the left seat. To return the
seats to their upright position, rotate the
seatbacks upward until you hear a click and
the seat latches.
note: This feature is operational when the vehicle
is in park and the liftgate has been open for less
than 10 minutes.
TilTinG hEAD RESTRAinTS* PAnORAMiC viSTA ROOF™
Your vehicle's front row head restraints can be
AnD POWER SUnShADES*
adjusted. Pull up to raise the head restraint.
To open, press and release the overhead
To lower, press the head restraint down while
moonroof switch
pressing and holding the guide sleeve adjust/
sunshades will open entirely, and the glass
release button. Tilt the head restraint forward
. panel will open to the first position. Press
for additional comfort by gently pulling the
again to fully open. To close, pull the switch
top of the head restraint. Once it is in the
down. The glass panel will stop at the first
forward-most position, tilting it forward once
position. Pull again and hold to fully close the
more will release it to the upright position.
glass panel and the sunshades.
note: Do not attempt to force the headrest To vent from a closed position, press the TilT
backward after its tilted. instead, continue tilting
button. To close from a venting position, pull
it forward until the headrest releases to the
the TilT button.
upright position.
MEMORY FUnCTiOn*
The memory function allows a "one touch"
recall of personalized memory features such
as; driver seat positions and power mirrors. Use
the memory controls located on the driver's
door to program and then recall memory
positions. To Program position 1, press and
hold until you hear a chime. To set a
second position, press and hold until the
same chime sounds. You can now use these
controls to recall the set positions.
*
(if equipped)
. The front and rear
15