Operation; Furnished Accessories; Optional Accessories - Shure SM86 User Manual

OPERATION

Power
The SM86 requires phantom power. This may be supplied to the
microphone from an external power supply (such as the Shure
model PS1A) or directly from preamplifi ers, mixers, or consoles
with built-in phantom power. Suitable sources should provide 11 to
52 Vdc phantom voltage.
Impedance
A load impedance of at least 600 Ohms is recommended. The load
may be as low as 150 Ohms, but a reduction in output level and
output clipping level will result.
SPECIFICATIONS
Transducer Type
Condenser (electret bias)
Frequency Response
50 to 18,000 Hz (see Figure 2)
+10
0
–10
2
20 50 100
TYPICAL FREQUENCY RESPONSE
Polar Pattern
Cardioid (see Figure 3)
250 Hz
500 Hz
1000 Hz 1000 Hz
TYPICAL POLAR PATTERN
Output Impedance
150 Ohms at 1 kHz
Recommended minimum load impedance: 600 Ohms
Sensitivity (at 1,000 Hz)
Open Circuit Voltage . . . . . . . . . . . . . . . –50 dBV/Pa (3.15 mV)
Output Clipping Level
1000 Ohm Load at 1,000 Hz . . . . . . . . . . . . . .+3 dBV (1.41 V)
Maximum SPL (at 1,000 Hz)
1000 Ω load (1% THD). . . . . . . . . . . . . . . . . . . . . . . . . . 147 dB
Self-Noise
23 dB typical, A-weighted
3 4 5 6 7 8 9 2 3 4 5 6 7 8 9
1000 10000
Hz
FIGURE 2
2500 Hz
6400 Hz
10000 Hz 10000 Hz
FIGURE 3
(1 Pa = 94 dB SPL)
Dynamic Range (1000 Ω)
124 dB (maximum SPL to A-weighted noise level)
Signal-to-Noise Ratio
71 dB at 94 dB SPL (IEC 651)*
*S/N ratio is difference between 94 dB SPL and equivalent SPL of
self-noise A-weighted.
Polarity
Positive pressure on diaphragm produces positive voltage on
pin 2 relative to pin 3 of the output connector. See Figure 4.
CAPACITOR
(ELECTRET
CONDENSER)
CARTRIDGE
BLACK
PEDANCE CON-
GREEN
Power
Phantom Supply Requirement . . . . . . . . 11 to 52 Vdc, positive
Current Drain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.2 mA
Connector
Three–pin (XLR) professional audio
Case
Dark gray enamel-painted steel with matte-fi nished silver
20000
colored steel grille
Dimensions
See Figure 5
24 mm
(.95 in.)
Net Weight
Net: 278 grams (9.8 oz)
Environmental Conditions
Operating: –18° to 60° C (0° to 135° F) (relative humidity <90%)
Storage: –29° to 74° C (–20° to 165° F) (relative humidity <80%)
CERTIFICATION
Eligible to bear CE Marking. Conforms to European EMC Directive
89/336/EEC. Meets applicable tests and performance criteria in
European Standard EN55103 (1996) parts 1 and 2, for residential
(E1) and light industrial (E2) environments.

FURNISHED ACCESSORIES

Break Resistant Microphone Clip . . . . . . . . . . . . . . . . . . . . . A25D
Microphone Bag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26A13
5/8" to 3/8" Thread Adapter 5/8" to 3/8" Thread Adapter . . . . . . . . . . . . . . . . . . . . . . . 5/8" to 3/8" Thread Adapter . . . . . . . . . . . . . . . . . . . . . . .

OPTIONAL ACCESSORIES

Phantom Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . PS1A
Shock Stopper. Isolation Mount . . . . . . . . . . . . . . . A55M, A55HM
Popper Stopper...Windscreen . . . . . . . . . . . . . . . . . . . . . A85WS
7.6 m (25 ft.) Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C25
2
FET IM- DISCRETE
LF RESPONSE
CLASS A
FILTER FILTER FIL
VERTER AMPLIFIER
REVERSE
VOLTAGE
PROTECTOR
SM86 BLOCK DIAGRAM
FIGURE 4
183 mm
(7.2 in.)
OVERALL DIMENSIONS
FIGURE 5
2 1
RFI FILTER
3
at both pins 2 and 3
49 mm
(1.92 in.)
31A1856