AOR SDU5500 Operating Manual

SDU5500 OPERATING MANUAL ADDENDUM
1. Use with the AR3000A
If using an AR3000A receiver with the SDU5500, section 4-2 page 17 describes the configuration of the AR3000A for use at
9600bps. Please ignore this reference and leave the radio configured to the factory default of 4800bps (the baud rate selection
slide dip switch pressed to the edge of the PCB).
In addition, when the SDU5500/AR3000A combination is used for the first time, the SDU5500 may display the wrong centre
frequency (receive frequency), receive mode and tuning step. Simply switch the SDU5500 off and on again to correct this.
The combination will continue to operate correctly until completely powered down and back on again... in this case simply
switch the SDU5500 off and on again following configuration.
2. Flash upgrade of CPU
The initial release firmware was V1.050 while later production carries V1.010, V1.011 (or higher), hold the decimal key of the
SDU5500 to display the firmware version number. As the CPU is flash up-gradeable, it is possible to upgrade ANY
SDU5500 by transferring a HEX file via the RS232 link using Windows HyperTerminal or similar software. Full details of
upgrade and the HEX file can be found on the AOR UK web site http://www.aoruk.com/software (follow the links to the
SDU5500). The paperwork describing the upgrade process and added RS232 commands is in Adobe Acrobat format on the
same internet site, a free Acrobat reader is available from the Adobe internet site at
http://www.adobe.com/acrobat
3. RS232 changes with later firmware releases
On the later versions of the SDU5500, the RIGD command is made invalid. In place of RIGD, RICD and RIFD should be used.
RICD command
Examples of response to RICD command
"ICD" + (CR)(LF).... Acknowledgement
"f" + frequency (MHz)... Frequency
", " .... divider
"l" + level(dbm)... Level
(CR)(LF)............. End
Basically this is equivalent to J command of the earlier SDU5000 with the exception of "ICD" up front.
Typical example of response
ICD
f80.0000,l-75
RIFD command
"IFD" + (CR)(LF).... Acknowledgement
"K" + (CR)(LF)....... Start of data download
Data (0 - FF, max 304 byte)..... Data
"k" +(CR)(LF)........ End of data download
This is equivalent to K command of the earlier SDU5000 with the exception of IFD up front.
With the SDU5500, volume of data is variable (in step resolution mode, etc) the length of data is also variable. WAIT when
remote-controlling the receiver via the SDU5500. The SDU5500 has a buffer which enables the operator to send commands
continuously.
Extra SDU5500 RS232 commands for the later firmware can be found in the UPGRADE Acrobat file stated above.
4. PC Windows software - FREE
A free software package to control the SDU5500 has been loaded onto the AOR web sites. The software provides a virtual
display of the SDU5500 with video recording via AVI files to the computers hard drive for later re-play and analysis.
Visit http://www.aoruk.com/software or check out the other AOR web sites http://www.aorja.com
http://www.aorusa.com
SDU5500 English language operating manual addendum V1.3 20/10/99
©AOR LTD, 1999 E&OE - Page 1
®
AOR Ltd
2-6-4 Misuji, Taito-ku, Tokyo 111-0055, Japan.
Tel: +81 3 3865 1695 Fax: +81 3 3865 1697
post@aorja.com www.aorja.com
AOR (UK) Ltd
4E East Mill, Bridgefoot, Belper, Derbys DE56 2UA, England
Tel: +44 1773 880788 Fax: +44 1773 880780
info@aoruk.com www.aoruk.com
AOR USA, INC.
20655 S. Western Avenue, Suite # 112
Torrance, CA. 90501, USA
Tel: (310) 787 8615 Fax: (310) 787 8619
info@aorusa.com www.aorusa.com