Listening To Ipad / Iphone/Ipod / Listening To Radio - iHome iDN38 Instruction Book

Listening to iPad, iPhone or iPod Using the Dock or USB Port
This unit features both a 30-pin dock (located on top of the unit) to play and charge iOS devices equipped with the older 30-pin
connector AND a USB port (located on back of the unit) which can play and charge both older iOS devices (such as iPhone 4,
iPad, etc.) AND Lightning devices using the charging cable that came with the device. NOTE: The USB port will NOT charge
iPad models.
Play and pause a device connected to the 30-pin dock using the
USB Button. Only one device can play at a time. Directions below apply to whichever dock/port you
the USB port using the
wish to control.
1. Connecting using the 30-pin Dock: Dock an already playing iPad, iPhone or iPod in the 30-pin dock on top of the unit. The
unit will automatically turn on and you will hear the audio playing from your iPad/iPhone/iPod.
Connecting using the USB port: Connect your iPad, iPhone, iPod or other device to the USB port located on back of the
unit using the USB charging cable that came with it.
Note: If the audio source volume is too low on the iPad/iPhone/iPod, the unit may not detect that the iPad/iPhone/iPod is in play
mode. If so, pressing the
2. When an iPad/iPhone/iPod is docked to the 30-pin dock or connected to the USB port and in standby mode, press the
Dock Button or
the Mode Button as needed until "Dock" or "USB" appears on the lower part of the display, indicating which dock/port on the
unit is in iPod mode.
3. Press the Dock Button or
4. Press the + or – Button on the unit to go to the next or previous track. Press and hold while track is playing for high
speed forward or reverse music search of the current track.
Adjusting Sound on the Unit
You can adjust the sound on the unit while listening to any sound source.
1. Press the or Button on the unit to adjust the system volume.
2. Press and hold the Mode/EQ Button to access EQ mode then press and release as needed to select Treble, Bass, or
Balance, then press the + or – Button to adjust settings.
TIP: You can also adjust EQ with the iHome Set app.
Setting up Antenna
Extend FM wire antenna fully for best reception. Do not strip, alter or attach to other antennas.
Tuning and Playing the Radio
1. Press and release the Mode Button as needed to turn on the unit and cycle through dock, USB, FM radio, and Aux-in modes.
2. When the desired FM mode is selected, press the + or – Button to tune the radio to a desired station. The current radio
frequency appears in the bottom of the display. Press the + or – Button for a few seconds to scan for the next clear station.
3. To memorize a station as a preset:
A. Press either Preset Button as needed to step through the 6 presets (P1 - P6) to the number you wish to assign, and
then hold the Preset Button until the selected preset number begins flashing in the display.
B. Press the + or – Button to tune the radio to a desired station. Hold briefly to have the radio autoscan/search for the next
clear station.
C. Press the Preset Button to confirm the setting, two confirmation beeps will confirm the setting and the preset number
you wish to assign. Repeat steps A-C to preset up to 6 stations.
4. To listen to a preset station, use the Mode Button to select FM mode, then press the
preset.
5. Press the or Button on the unit to adjust the system volume.
6. To stop listening at any time, press the
Dock Button or USB Button on the unit once should make it play.
USB Button on the unit to play the iPad/iPhone/iPod. If the unit is already on, press and release
USB Button on the unit to pause play; press again to resume play.
Listening to Radio
Button on the iDN38 to turn it off.
Listening to Radio
Dock Button, and play and pause a device connected to
Preset Button to choose the desired
8
P10