Advertisement
Quick Links
Advertisement
Related Manuals for Whirlpool LDE7800W1
Summary of Contents for Whirlpool LDE7800W1
- Page 1 ill_'h.lllilliIDll ill,_'h'ntliIDllS Electric Dryer...
- Page 2 Before you begin read the following instructions completely and carefully. They will simplify the installation. AFTER COMPLETING INSTALLATION, SAVE THESE INSTRUCTIONS FOR FUTURE USE. IMPORTANT: OBSERVE ALL GOVERNING CODES AND ORDINANCES Where to install the dryer Physical Characteristics The site must be large enough _o--r_ dr--_ a-T_-w room...
- Page 3 IMPORTANT: ELI CT£ICAL REQUIREMENTS OBSERVE GOVERNING CODES AND ORDINANCES 5. CAUTION: For mobile home installations, the appliance 1. A three-wire or four-wire single phase 120/240 volt wiring must be revised. The appliance frame must not be Hz AC only electrical supply three-wire or four-wire...
- Page 4 DO NOT USE 3 INCH EXHAUST DUCT I 2. You can get the parts need installation from your Whirlpool parts distributor or your local plumbing heating store. 3. We strongly recommend exhausting dryer to the outside...
- Page 5 TURNS exhaust air to be directed inside to conserve energy during winter months. These devices may be used with Whirlpool dryers providing their use does not violate national or local codes and providing the device does not restrict exhaust MAXIMUM 43FT.
- Page 6 'i'YPICAL EXIlAUS 1 lN_ I ,_,[_]__.\'I'!()X 14. Formobile home installations thedryermustbeex- hausted t o the outside. If the dryer is exhausted through R,G,D METAL'I the floor and the area under the mobile home is enclosed, the exhaust system must terminate outside the enclosure.
- Page 7 IN TALLATION INSTRUCTIONS DO NOT GRASP APPLIANCE BY THE CONSOLE Next wipe the interior of the drum thoroughly with a damp MOVE APPLIANCE INTO EXACT cloth before using the dryer. LOCATION UNTIL FOLLOWING STEPS HAVE BEEN PERFORMED C. INSTALL DRYER LEVELING FEET REMOVE...
-
Page 8: D, Electrical Connection
D, ELECTRICAL CONNECTION It is the personal responsibility of the customer to contact Replace the terminal block cover by first installing qualific'd installer to assure that the electrical installation the tab of the cover into the slot of the dryer rear adequate and is in conformance... - Page 9 *Cold water pipe must have metal continuity electrical ground power cupp! V cnrd !'J} £_OII[IU_L LII_ II_Ut. wl,c interrupted plastic, rubber other electrically to _he center silver colored terminal of the terminal insula[]ng connectors (including water meter pump) without block connect other wires...
- Page 10 PLAIN-END FIELD WIRING NOTE: terminal connections at the dryer terminal block are suitable connection of No. 10 copper wire only. Plain-end field wires must be fastened between terminals of the terminal block and the nuts of the terminal EXTERNAL GROUND CONNECTOR block screws as shown...
- Page 11 E. FINAL INSTALLATION CONNECTIONS Make the electrical connection: 1. Move dryer to its operating position and check Plug the flexible connector (pigtail) into an approved level of the machine using a small spirit level. The dryer receptacle (where local codes permit be leveled from...
- Page 12 INSTRUCTIONS FOR RECESSED OR CLOSET INSTALLATIONS PREVENT LARGE AMOUNTS LINT RECESS INSTALLATION *D**' MOISTURE FROM ACCUMULATING NON-EXHAUSTED (DEFLECTOR MAINTAIN DRYING EFFICIENCY, THIS MACHINE LCK4000 REQUIRED) MUST BE EXHAUSTED OUTDOORS. EXHAUSTED CLOSET CLOSET INSTALLATION *1_* "'H DOOR EXHAUSTED ONLY 24sq. 485q. Unobstructed openings required...
- Page 13 1. Read O perating instructions Book and Dryer G uide. TYPICAL INSTAI,I,.\TiON 2. Dryer w illnotoperate withthedoor o pen. 3. Keeplint screen a ndexhaust system clearof lint. A blocked screen o r exhaust will cause s lowdrying and/or other m alfunctions. Donotoperate d ryerwithoutLint s creen.
- Page 14 i ,l() i[NG OPERATIONS PROCEDURE 1. Shul electric supply _o dryer by opening circuit 4. Apply filament tape from inside drum, the door breaker or fused disconnect. opening to the front panel to prevent drum movement. 5. Use tape to secure clothes door and lint screen.
-
Page 15: Rack Installation
LITEI{ATURE RACK INSTALLATION 1. Insert the 4 side tabs (2 on each side) the rack into the back panel. (See FigureA) RACK 2. Push downward until 4 tabs bottom out, locking sides of rack in place. 3. Insert 2 bottom tabs into the slots... - Page 16 WHIRLPOOL appliance should need service, call dealer from whom purchased appliance a WHIRLPOOL franchised TECH-CARE®service company He is in the Yellow Pages your telephone directory listed under Washers, Dryers-Repairing Servicing. also obtain name number dialing, free, wi[hin continental...