Advertisement
Installation
Instructions
30" Built In Wall Oven
JTP15AA, JTP15BA,
JTP17SC, JTP18WA, JTP18AA,
JTP18BA, JTP18WA, JTP27BA, JTP27WA, JTP45BA,
JTP45WA, JTP47SC, JTP56AA, JTP56BA, JTP56WA,
JT910AA, JT910BA, JT910CA, JT910SA, JT910WA,
JT950AA, JT950BA, JT950CA, JT950SA, JT950WA,
ZET737BA, ZET737WA, ZET757BA, ZET757WA
Questions? Call GE Answer Center at 800.626.2000 orvisit
our
Website at: www.geappliances.com
Before you begin
Read these instructions carefully and completely
• IMPORTANT-Save
these instructions
for
local inspector's
use.
• IMPORTANT-Observe
all governing
codes and ordiances.
• Note to Installer-
Be sure to leave these
instructions
with the consumer.
• OWNER-
Keep these instructions
for future
reference.
• NOTE- This appliance
must be properly
grounded.
IPa s.nc.u,e, IIMa,eria.s,ee I
4 screws
(single)
8 screws
(double)
Bottom Trim
Wire Nuts
Junction
Strain Relief
Box
k_
Clamp
I Tools You Will Need
I
36" of String
1/8" Drill Bit &
Phillips
Electric or
Screwdriver
Hand Drill
Pub. No. 31-10435
229c4053P417
1
Advertisement
Table of Contents
Related Manuals for GE JTP15AA
Summary of Contents for GE JTP15AA
- Page 1 JTP45WA, JTP47SC, JTP56AA, JTP56BA, JTP56WA, JT910AA, JT910BA, JT910CA, JT910SA, JT910WA, JT950AA, JT950BA, JT950CA, JT950SA, JT950WA, ZET737BA, ZET737WA, ZET757BA, ZET757WA Questions? Call GE Answer Center at 800.626.2000 orvisit Website at: www.geappliances.com Before you begin • Note to Installer- Be sure to leave these instructions with the consumer.
-
Page 2: Important Safety Instructions
Installation Instructions IMPORTANT SAFETY INSTRUCTIONS Electrical For Your Safety Requirements • Be sure your oven is installed properly a qualified installer or service technician. This appliance must be supplied with the • Be sure the oven is securely installed in a proper voltage and frequency, and connected cabinet that is firmly attached to the... -
Page 3: Pre-Installation
Installation Instructions Pre-Installation Checklist Open the door to the stop position. ON THE FOLLOWING PAGES ARE TO BE USED FOR SINGLE AND DOUBLE OVEN INSTALLATION! Remove packaging materials. Check behind hinges, and under false bottom. Remove labels on door, plastic on trims and panel, and all tape around oven. - Page 4 Installation Instructions Pre-Installation Checklist cont Place the oven on a table or Cover hinge with paper towel rolls platform even with the cutout or toweling. opening. (Platform must support 150 Ibs. single, 275 Ibs double.) Remove the bottom trim from the CAUTION: When the door is top of the oven.
- Page 5 Installation Instructions Cutouts for Single Built-In-Oven CUTOUT WIDTH Cabinet Width 30" _--.-28112"MIN._..,_ 285/8"MAX.-- Recommended Cutout Location JUNCTION from Floor 32 1/2" LOCATION ALLOW 11/16"FOR OVERLAPOFTHE OVEN OVER SIDE _ 23 1/2" Min. Cutout Depth EDGES OF CUTOUT THE OPENING BETWEEN INSIDE 22"TO CUTOUT WALLS...
- Page 6 Installation Instructions Cutouts for Double Built-In-Oven CUTOUT WIDTH _F- 28 1/2" MIN. 28 5/8" MAX. Cabinet Width 30" JUNCTION Recommended LOCATION Cutout Location from Floor 12" ALLOW 11/16" FOR OVERLAP OFTHE OVEN 23 1/2" Min. Cutout Depth OVER SIDE EDGES OF CUTOUT Cutout Wdth 28 1/2"...
- Page 7 Installation Instructions Cutouts For Single Oven Under Counter Gas or electric cooktops may be installed over this oven. See cooktop installation instructions for cutout size. Gas and electrical connections See label on top of oven for approved cooktop models. for 30" gas cooktop must be located in an adjacent accessible 240V / 208V location to the right.
- Page 8 Installation Instructions Turn off the circuit breaker or remove NEW CONSTRUCTION AND FOUR- fuses to the oven branch circuit. CONDUCTOR BRANCH CIRCUIT CONNECTION With the oven in front of the cabinet opening, on a table or platform, connect the flexible conduit to the electrical •...
-
Page 9: Electrical Connections
Installation Instructions Electrical Connections cont. Do not shorten the flexible conduit.The conduit strain Relief Clamp must be CIRCUIT CONNECTION I THREE-CONDUCTORBRANCH securely attached to the junction and the flexible conduit must be securely attached to the clamp. If the flexible conduit will not fit within the When connecting to a 3-conductor... -
Page 10: Securing The Oven
Installation Instructions Securing the Oven With the conduit connected, the oven IC---_ Drill four-I/8" pilot holes through the is ready to be slid into the cutout mounting holes (top and bottom) of the opening. side trim, for the four #8 screws provided. - Page 11 Installation Instructions I-D-1 Installing the Bottom Trim Key hole slot and wide flange at top ake sure the flat side is up on the bottom trim. ind the Key Slot on the back of the trim. atch the key slot with the rivet on the bottom of the side trim Lower trim mounting rivet on bottom of side...
-
Page 12: Replacing The Oven Door
Installation Instructions Replacing the Oven Door Make sure the hinge is in the door stop position. Remove the toweling or paper towel holder from the hinge. Grasp the door on both sides. Hold the door over the hinges lining up the hinges with the hinge slots on the bottom of the door. -
Page 13: Pre-Test Check List
Installation Instructions Pre-Test Check List Check that the bottom trim is installed Remove all protective film if properly (see page 11). present, and any stickers. Check to be sure that all wiring is Check to be sure the mounting secure and not pinched or in screws are installed and flush with the contact with moving parts. - Page 14 NOTES...
- Page 15 NOTES...
- Page 16 NOTES Pub. No. 31-10435 229c4053P417...