Related Manuals for Lite-on Tech Scenic Edition X101
Summary of Contents for Lite-on Tech Scenic Edition X101
- Page 1 Lite-On Tech Corp. SCENIC Edition X101 Mainboard USER’S MANUAL Intel® Pentium® 4 Processor Motherboard Rev. 1.0...
- Page 2 COPYRIGHT Copyright by LITE-ON, (LITE-ON Technology Corp.). No part of this manual may be reproduced or transmitted in any form without the expressed, written permission of LITE-ON Technology Corp. TRADEMARKS LITE-ON is a registered trademark of LITE-ON Technology Corp. Other names, trademarks listed here are the property of their respective owners.
-
Page 3: Table Of Contents
Contents Chapter 1: Introduction....................4 1-1 SCENIC Edition X101-Mainboard Specification and Features ......... 4 1-2 SCENIC Edition X101-Mainboard Layout Diagram ............6 1-3 Back Panel Connectors Diagram..................6 Chapter 2: Hardware Installation ................. 7 2-1 Installing the Motherboard ....................7 2-2 Install the CPU and Heatsink.................... -
Page 4: Chapter 1: Introduction
Chapter 1: Introduction SCENIC Edition X101-Mainboard Specification and Features Processor Socket478 (CPU Clear Out Zone) Support single Intel® Pentium 4 3.06GHz+ 400/533 Mhz (Willamette /Northwood) & Celeron processor Chipset Intel 845GV Intel ICH4 Super I/O SMSC LPC47M192 Front Side Bus Frequency... -
Page 5: Additional Features
Industrial Standard PCI 2.2 compliant USB 2.0 Additional Features Keyboard/Mouse/USB wake up Support S1,S3,S4 and S5 ACPI status Hardware monitor capability Rear Side I/O Ports 1 x PS2 keyboard port 1 x PS2 mouse port 4 x USB ports 1 x RJ-45 LAN connector (option) 1 x Serial port 1 x Parallel port 1 x VGA connector... -
Page 6: Scenic Edition X101-Mainboard Layout Diagram
1-2 SCENIC Edition X101-Mainboard Layout Diagram Figure 1-2. SCENIC Edition X101-Mainboard Layout Diagram 1-3 Back Panel Connectors Diagram Figure 1-3. Back Panel Connectors... -
Page 7: Chapter 2: Hardware Installation
Please REMOVE the metal studs or spacers if they are already fastened on the chassis base and are without mouting-holes on the motherbard to align with. 2-2 Install the CPU and Heatsink ® ® This motherboard uses a CPU socket called Socket478 to install the 478 pin Intel Pentium 4 & ® Celeron CPU. -
Page 8: Install System Memory
The following set of rules allows for optimum configurations. NOTE: Intel 82845GV supports DDR333 SDRAM. Locate the DDR DIMM slot. Push the white retaining clips on each side of the DDR DIMM slot outward. -
Page 9: Jumpers, Connectors, Headers And Indicators
2-5 Jumpers, Connectors, Headers and Indicators Inside the case of any computer there are several cables and jumpers that have to be connected. These cables and jumpers are usually connected one-by-one to connectors located on the board. During the installation you have to pay attention to the orientation of the connectors, headers and the cables. -
Page 10: Chapter 3: Bios Setup
Chapter 3: BIOS Setup The BIOS is a boot program located in a Flash Memory chip on the mainboard. It is used to communicate with the hardware before the operating system (OS) takes the control of the system. Its main function is to manage the setup of the motherboard and interface card parameters, including simple parameters such as time, date, hard disk drive, as well as more complex parameters such as hardware synchronization, device operating mode, and the operating speed of the CPU. -
Page 11: Standard Cmos Setup
2. Standard CMOS Setup This setup page includes all the basic configuration parameters of the BIOS. Including the date, VGA, FDD and the HDDs settings. Use the ↑↓←% → keys to select the items and press <Enter> to confirm and enter the sub-menu. Time (hh: mm: ss): You can set the time in this item: hour (hh), minute (mm) and second (ss). -
Page 12: Power Management Setup
Enable: IRQ 20-23 (Default) Disable: IRQ 09-11 Hyper-Threading Technology: Allows you to enable or disable the Intel Hyper-Threading Technology. (This item only selectable when Intel HTT CPU is plugged –in) Enable: Intel HTT function enable (BIOS auto detect) Disable: Intel HTT function disable (BIOS auto detect) Internal Graphic Mode Select Allows you to select the size of memory for the internal graphic adapter. -
Page 13: Peripherial Setup
Disable: OnBoard LAN Chip Boot ROM disable Enable: OnBoard LAN Chip Boot ROM enable (Default) Intial Graphics Adapter Priority: Allows you to set the initial priority of the Graphics Adapter. (SCENIC Edition X101-Mainboard GE/GV has a different option) SCENIC Edition X101-MainboardGE SCENIC Edition X101-MainboardGV AGP/Int-VGA... - Page 14 USB Controller: Allows you to enable or disable the USB Controller. Disable: USB Contoller disable Enable: USB Controller enable (Default) USB 1.1 Device Legacy Support: Allows you to set the USB 1.1 Device Legacy Support under DOS mode. Disable: USB 1.1 Device Legacy Support disable No Mice: Only Mice is not supported All Device: All device support OnBoard Serial Port:...
-
Page 15: Hardware Monitor Setup
This setup page describes the PC health status, including temperature (CPU, system), fan speed (CPU, system, chassis) and the voltage (CPU, AGP, system power). CPU Ratio Selection: Allows you to setup the Intel P4 and Celeron CPU ratio CPU Warning Temperature: System will warn when the CPU temperature reaches above 85°C/185°F CPU Shutdown Temperature: System will shutdown when the CPU temperature reaches above 90°C/194°F... -
Page 16: Password Option
+12.0V: Current ATX Power +12.0V detect. 7. Password Option The Password Option screen allows users to setup password and execute checking function. Change Supervisor Password Allow you to set and change the Supervisor Password. Password Status This feature shows Password Status. Password Check Allows you to set the Password Check when Supervisor Password setup.