Garmin Gladiator TR-1 Owner's Manual
  1. Manuals
  2. Brands
  3. Garmin Manuals
  4. Marine Equipment
  5. Gladiator TR-1
  6. Owner's manual

Garmin Gladiator TR-1 Owner's Manual

Garmin gladiator lcd heading display owner's manual tr-1
Hide thumbs Also See for Gladiator TR-1:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Owner's Manual
TR-1 Gladiator
LCD Heading Display
Installation & Operations
Owner's Manual
1-800-588-7655
www.nautamatic.com
906-2700-00
Version 03

Advertisement

Table of Contents
loading

Related Manuals for Garmin Gladiator TR-1

Summary of Contents for Garmin Gladiator TR-1

  • Page 1 TR-1 Gladiator LCD Heading Display Installation & Operations Owner’s Manual 1-800-588-7655 www.nautamatic.com 906-2700-00 Version 03...
  • Page 2 TR-1 Gladiator LCD Heading Display Thank you for purchasing the TR-1 Gladiator Display. This guide contains an explanation on how to install and use your new TR-1 Display. Please be sure to read this instruction manual fully to familiarize yourself with the features and proper installation and operation of this display.
  • Page 3 You are responsible for the safe and prudent operation of your vessel. Your TR-1 Autopilot is a tool that will enhance your capability to operate your boat and catch fish. It does not relieve you from the responsibility for safe operation of your vessel.

  • Page 4: Installation Overview

    Installation of Basic LCD Display Installation Overview: • Figure out where on your dash you want to mount the display, or optional mounting panel. Be sure to allow plenty of room in the back of the display for mounting accessibility. •...

  • Page 5: Mounting The Display Unit

    Mounting the Display Unit You will want to decide where to mount the display unit. Mount the display in a place where you have good visibility and a convenient reach to the dial. (The outside diameter is 4” and 4-1/2” with the trim ring.) Using template (A) provided, you have two options for mounting the Standard display unit: Type I Template: Cut a 3-3/4”...
  • Page 6 Connecting the Display Wiring o Optional Rudder Indicator Connection to Optional rudder indicator unit. Red= ( + ) Positive Black= (- ) Signal Silver= (Grnd) Connects to the ECU’s Connection # 3 Connects to the autopilot’s handheld Page 5...
  • Page 7 Connecting the Display With Wireless Remote Option 1 Connects to the ECU’s Connection Display Wireless Receiver Connects to the autopilot’s handheld Connects to the ECU’s Connection Wireless Receiver Display Connects to the autopilot’s handheld Page 6 Option 2...

  • Page 8: Operating The Display

    Steering Mode Rudder Angle or Turn Rate Indicator Setting your display for accurate heading output: The heading display displays the current heading of the vessel. The compass must be calibrated and north set for this display to be correct. Please see your Gladiator’s Owner’s Manual for these instructions.

  • Page 9: Display Elements

    Display Elements: The Three large digits on the display show the current heading in degrees. (See Figure 10) Figure 10 If the autopilot is in calibration mode, (Autotune, Compass Calibration, or rudder calibration) the three digits will display “CAL”. Figure 11 The Three smaller digits display a horizontal bar (See Figure 12) if the heading command mode is available.
  • Page 10 Heading Command Display The heading command display will be blank if the heading command function is unavailable. Figure 16. whenever the autopilot is in heading hold (AUTO) and the display turn rate command is inactive. It will display a single horizontal bar until the operator enters a heading command by turning the command knob.
  • Page 11 Rate of Turn Command Dial The “Rate of Turn Command Dial” on the display controls the boat somewhat like your steering wheel at the helm. Turning the dial either clockwise or counterclockwise will cause the autopilot to execute a turn and make a continuous rate of turn until the dial is turned in the opposite direction until only a single vertical bar is displayed.

  • Page 12: Rudder Calibration

    Rudder Position Display The rudder position display is optional. If you wish to use this portion of the display, you will need to purchase an aftermarket transducer unit. The rudder position display is activated by a mode selection from the handheld on the autopilot.
  • Page 13 to illuminate the 5 LED, and pressing and releasing the [Right Chevron Button] Three (3) times to illuminate the 9 LED. 3. Press the [up arrow] button on the handheld remote, the up arrow LED will light and the display will indicate CAL. 4.

Table of Contents