Epson STYLUS PRO PRO WT7900 Quick Reference Manual
Garmin all in one printer user manual
Hide thumbs
Also See for STYLUS PRO PRO WT7900:
- User manual (136 pages) ,
- Reference manual (46 pages) ,
- Network manual (33 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Epson STYLUS PRO PRO WT7900
Summary of Contents for Epson STYLUS PRO PRO WT7900
- Page 1 Epson Stylus Pro WT7900 ® QUICK REFERENCE GUIDE...
-
Page 2: Printer Parts
Printer Parts Front Roll paper holder Front cover Ink bay Film basket guide Film basket Back Optional SpectroProofer port USB port Maintenance tank Roll paper cover Paper basket Network interface port Control panel Ink bay Manual holder Casters AC inlet... - Page 3 Loading Epson Media Open the roll paper cover. Push the lock lever down firmly, then move the roll paper holder to the left. Set the roll paper on top of the printer. If necessary, adjust the roll paper adapters to fit the core size of the roll paper. Then release the tension lever on each adapter. 2-inch core Push the adapters into the paper core at both ends of the roll. Then press down on the tension levers to secure the adapters on the roll. Move the roll paper all the way to the right. Slide the roll paper holder to align the the roll paper adapter. 3-inch core Roll the paper slowly into position. arrow with...
- Page 4 Loading Epson Media (continued) Grasp the left roll paper holder and slide it to the right as far as it will go. Make sure the roll paper is pushed all the way to the right. Pull up the lock lever to lock the paper in place. Press the paper source button until appears on the display. Choose paper automatically after each page is printed, to decide for yourself when to cut the paper. Removing Epson Media Open the roll paper cover. Press the button to release the paper. The paper rewinds automatically. If you don’t plan to reload paper immediately, press button again to exit paper loading mode. Push down the lock lever firmly to release it. Then grasp the roll paper holder and slide it all the way to the left to release the roll. If the load paper. Insert the paper all the way into the slot. If the paper doesn’t come out, lower the suction by pressing the after the paper is loaded. Close the roll paper cover. Press the paper to move into position. to cut the Select the paper type setting (such as ClearProof Film) to match the type of paper you’ve loaded. Roll the paper forward so it rests on top of the printer. Pull up the tension levers, then remove the adapters from the paper roll.
-
Page 5: Checking And Cleaning The Print Head
Shaking the White Ink Cartridge To maintain optimal image quality, remove the white ink cartridge and shake it once a week. The printer will tell you when this is required: Alert that shaking is required Days until next required shaking Press the button to unlock the ink bay. Press to select OPEN LEFT COVER, then press OK. Open the cover and remove the white ink cartridge. Checking and Cleaning the Print Head Checking the Nozzles The printer automatically checks the nozzles and cleans them if necessary, but you can also check them yourself. Make sure roll paper or letter- or A4-size cut sheet paper is loaded in the printer. If you need to check the white ink nozzles, use film to ensure that the ink is visible. Menu. Press until TEST PRINT is selected, then press Press... -
Page 6: Cleaning The Nozzles
Checking and Cleaning the Print Head (continued) Cleaning the Nozzles Press the cleaning button on the control panel. Press to select one of the following: NORMAL CLEANING—Press OK to start the • cleaning cycle. CLEAN COLOR PAIRS—Press OK, select the • color pair you want to clean, then press OK to start the cleaning cycle. Use if you know which color(s) you need to clean; this saves ink from being used unnecessarily to clean working nozzles. POWER CLEANING—Press OK to start the • cleaning cycle. Use only if three cycles of normal cleaning doesn’t clear the nozzles. Aligning the Print Head If your prints look grainy or blurry, or you see misregistration or “ghosting,” you need to align the print head. Load the bundled roll paper included with the printer. You can also use Epson film or other compatible Epson media. For best results, use the same width of paper that you plan to print with. -
Page 7: Replacing Ink Cartridges
Checking Ink Levels and Replacing Ink Cartridges Before you begin a large print job, you should check your ink levels. If one of your cartridges is low, you can replace it before you start. Or you can wait until the ink runs out, replace the cartridge, and then continue the job. Checking Ink and Maintenance Tank Levels The easiest way to check ink levels is from the control panel. The numbers above the ink cartridge icons correspond to the 11 cartridge slots in the printer. Ink gauges for 11 cartridges listed below Replacing Ink Cartridges When one of the ink icons flashes, and INK LOW is displayed on the LCD, the cartridge is nearly expended. Check the LCD to see which cartridge is low, and make sure you have the correct replacement cartridge. Epson UltraChrome ® HDR ink cartridges Slot Cartridge 150 ml... -
Page 8: Replacing The Paper Cutter
Checking Ink Levels and Replacing Ink Cartridges (continued) Make sure the replacement cartridge is the correct color, and remove it from its package. Gently shake the cartridge before installing it: 30 seconds for the white ink cartridge, or 5 seconds for all others. Hold the cartridge with the arrow mark pointing toward the printer. Then insert the cartridge into the slot. Don’t force it. Replacing Printer Parts Replacing the Paper Cutter If you notice that the paper isn’t cut cleanly, you may need to replace the cutter (part # C12C815331). Press the Menu button on the printer, then press until MAINTENANCE is highlighted. Press again. Press to highlight CUTTER REPLACEMENT. Press to display EXECUTE, then press OK. The paper cutter moves to the replacement position. Turn off the printer. Note: If you can’t insert the cartridge smoothly, you may have the wrong cartridge. -
Page 9: Replacing The Maintenance Tank
Replacing Printer Parts (continued) Carefully remove the cutter. Insert the new cutter. Make sure the cutter pin goes into the hole. Tighten the screw. Insert the cutter cover, then press it in until it snaps into place. Turn the printer back on. Run the cutter adjustment from the Maintenance menu using the control panel. Replacing the Maintenance Tank You need to replace the maintenance tank (part # C12C890191) when you see MAINTENANCE TANK FULL on the LCD, the icon has an X, and the printer won’t print. Turn off the printer. Pull out the maintenance tank as shown. Caution: Do not tip the tank or ink may spill out. Place the used tank in the plastic bag included with the new tank and dispose of it carefully. Insert the new tank. -
Page 10: Control Panel Menus
Control Panel Menus Control Panel Menus Boldface type indicates the default setting. Press the Menu button to access the menus. See the User’s Guide for details. Menu Item PRINTER SETUP PLATEN GAP PAGE LINE ROLL PAPER MARGIN PAPER SIZE CHECK PAPER SKEW CHECK REFRESH MARGIN AUTO NOZZLE CHECK PRINT NOZZLE PATTERN AUTO WT INK REFRESH INITIALIZE SETTINGS TEST PRINT NOZZLE CHECK STATUS SHEET... - Page 11 Control Panel Menus (continued) PAPER SETUP ROLL PAPER REMAINING REMAINING PPR SETUP ROLL PAPER LENGTH ROLL LENGTH ALERT PAPER TYPE CUSTOM PAPER PAPER TYPE PLATEN GAP THICKNESS PATTERN PAPER FEED ADJUST DRYING TIME PAPER SUCTION SET ROLL PAPER TENSION REMOVE SKEW HEAD ALIGNMENT PAPER THICKNESS SELECT PAPER TYPE...
-
Page 12: Where To Get Help
Where To Get Help Service Access Telephone support Call (888) 377-6611. Make sure you have your Unit ID number. If you experience any difficulty with the toll-free number or your Unit ID number, call (562) 276-1305. Internet Go to epson.com/support to download drivers and firmware, access product documentation and troubleshooting, and get technical advice through e-mail. - Page 13 Control Panel Lights and Buttons Paper light Power light and button Pause/reset light and button Ink light Head cleaning button Ink cover open button Paper source button Paper feed button (up) Paper release (ePlaten™) light and button Menu button Paper cut button OK button Paper feed button (down) Printed in USA...