Summary of Contents for Windsor Saber Cutter SCX264
Page 1
WALK BEHIND SCRUBBER Operating Instructions (ENG) Instrucciones de funcionamiento (SPA) MODELS: SCX264 SCXC264 BSCSCX264 10052380 10052430 10052860 SCX324 SCXC324 10052390 10052440 IPX4 Read these instructions before using the machine Lea las instrucciones antes de utilizar la máquina 86039080 - BP 01/24/13...
Warranty Registration Thank you for purchasing a Windsor product. Warranty registration is quick and easy. Your registration will allow us to serve you better over the lifetime of the product.
The OPERATIONS section is to familiarize the correct repair parts. operator with the operation and function of the machine. Parts may be ordered from authorized Windsor dealers. When placing an order for parts, the The MAINTENANCE section contains preventive machine model and machine serial number are maintenance to keep the machine and its important.
IMPORTANT SAFETY INSTRUCTIONS When using an battery powered appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. WARNING: To reduce the risk of fire, electric shock, or injury: Use only indoors. Do not use outdoors or expose to rain. Use only as described in this manual.
WHEN SERVICING MACHINE: Avoid moving parts. Do not wear loose clothing; jackets, shirts, or sleeves when working on the machine. Use Windsor approved replacement parts. WARNING Batteries emit hydrogen gas. Explosion or fire can result. Keep sparks and open flame away. Keep top cover in raised position when charging.
SAFETY LABEL LOCATION NOTE: These drawings indicate the location of safety labels on the machine. If at any time the labels become illegible, promptly replace them. SAFETY DECAL 86252530 PRV NO. 81494 BATTERY CAUTION 86252520 PRV NO. 80885 CIRCUIT BREAKER DECAL 86243530 SEE MANUAL PRV NO.
TECHNICAL SPECIFICATIONS ITEM DIMENSION/CAPACITY Nominal power 1450 W Rated Voltage 24VDC Rated Amperage 60 Amps Batteries 4 X 6 Volt 250-305-335AH @ 20 hr rate Scrub Brush Motors 2 X .75 hp (0.56 kW) Vacuum Motor .75 hp (0.56 Kw) Propelling Motor .3 hp (0.22 Kw) Mass (GVW)
Page 9
TECHNICAL SPECIFICATIONS ITEM MEASURE Height 45 in. (114 cm) Length with 26 in. (66 cm) scrub head 64 in. (163 cm) Length with 32 in. (81 cm) scrub head 66 in. (167 cm) Width without squeegee and scrub head 24 in. (61 cm) Width of squeegee for 26 in.
HOW THE MACHINE WORKS The Saber Cutter is a battery powered, self- propelled, hard floor scrubber intended for The function of the recovery system is to vacuum commercial use. The appliance applies a the soiled water back into the recovery tank. The cleaning solution onto a hard floor, scrubs the recovery system consists of the squeegee, floor with brushes, and then vacuums the soiled...
COMPONENTS 1. Control Panel 2. Front Cover 3. Recovery Tank 4. Recovery Tank Drain Hose 5. Scrub Head Shrouds 6. Solution Tank 7. Solution Tank Cover 8. Solution Tank Drain Hose 9. Solution Strainer 10. Squeegee 11. Aqua-Mizer 12. Top Cover 13.
Page 13
CONTROLS 1. Key Switch 10. Squeegee Lift Lever 2. Emergency Shut Off Switch (Optional) 11. Squeegee Pitch Adjustment Knob 3. Speed Control Knob 12. Squeegee Deflection Adjustment Knobs 4. Propel Control Lever 13. Battery Charge Level Indicator 5. Reverse Button 14.
Page 14
CONTROLS 7. ACTUATOR SWITCH 10. SQUEEGEE LIFT LEVER Adjusts the amount of brush pressure to the Raises and lowers the squeegee. floor by raising or lowering the scrub deck. To lower the squeegee, lift the lever from its raised position. To increase brush pressure, press the bottom of the switch.
Page 15
CONTROLS 13. BATTERY CHARGE LEVEL INDICATOR Indicates the charge level of the batteries. The meter display is divided into 10 vertical bars. Bar illuminated on the far right indicate full charge. Bars flashing near the left side indicate the batteries should be recharged. Further operation of the machine could damage the machine or the batteries.
MACHINE OPERATION FILLING SOLUTION TANK PRE-RUN MACHINE INSPECTION FOR SAFETY: Before leaving or servicing Do a pre-run inspection to find possible problems that machine; stop on level surface, turn off machine could cause poor performance or lost time from and remove key. breakdown.
MACHINE OPERATION NORMAL SCRUBBING TO BEGIN SCRUBBING Plan the scrubbing pattern in advance. The WARNING longest track is around the perimeter of the area to be cleaned. For efficient operation, the runs When operating the machine around people, pay close attention for unexpected movement. Use should be the longest possible without turning, extra caution around children.
MACHINE OPERATION DOUBLE SCRUB RECOVERY TANK 1. Unhook the large drain hose from the retainer. For floors which are heavily soiled or have thick Unscrew the T-handle on plug enough to loosen accumulations of floor finish may not clean plug, then lower hose in direction of the drain. sufficiently with one pass.
MAINTENANCE SERVICE SCHEDULE MAINTENANCE DAILY WEEKLY MONTHLY Check batteries after charging; add water if necessary Check pad wear to prevent buildup of chemicals Check linkages and connectors for wear and damage Check hoses for wear, blockages, or damage Clean squeegee; check for adjustment; inspect for wear Check handles, switches, knobs, domes, and gaskets for damage Clean out recovery tank...
MAINTENANCE 1. BATTERIES CAUTION The batteries provide the power to operate the When servicing machine, avoid contact with machine. The batteries require regular maintenance battery acid. to keep them operating at peak efficiency. WARNING The machine batteries will hold their charge for long Batteries emit hydrogen gas.
MAINTENANCE CHECKING BATTERY SPECIFIC GRAVITY TO CHARGE THE BATTERIES Use a hydrometer to check the battery specific WARNING gravity. When servicing machine, avoid contact with battery acid. CAUTION Battery Check Batteries emit hydrogen gas. Explosion or fire can result. Keep sparks and open flame away. Keep covers open when charging.
MAINTENANCE 5. Replace the battery caps, and leave them in CHANGING BATTERIES place while charging. Stop the machine in a clean area next to the 6. Unplug the battery connector from the machine. charger. Turn off machine. FOR SAFETY: When charging, connect the FOR SAFETY: Before leaving or servicing the charger to the batteries before connecting the machine;...
MAINTENANCE 2. SQUEEGEE BLADES TO REMOVE SQUEEGEE ASSEMBLY The front squeegee blade allows solution to pass 1. With the squeegee in the up position, turn key through channels in the blade into the squeegee switch “OFF”. assembly while maintaining vacuum to provide lift. 2.
MAINTENANCE TO ADJUST SQUEEGEE PITCH TO ADJUST AMOUNT OF REAR SQUEEGEE DEFLECTION 1. Choose a smooth, level surface. Turn “ON” the key switch. Lower the squeegee and drive 1. Choose a smooth, level surface. Lower the forward at least 2 feet (60cm.). squeegee and drive forward at least 2 feet 2.
MAINTENANCE SCRUB BRUSHES REPLACING OR INSTALLING SCRUB BRUSHES There are four different types of brushes available to cover applications from cleaning heavily soiled floors 1. With the scrub deck up, turn “OFF” the machine. to polishing. A pad driver is also available to take advantage of the many cleaning pads on the market.
MAINTENANCE 6. SOLUTION STRAINER BRUSH MOTOR CARBON BRUSH The solution strainer is located in front of the left REPLACEMENT front wheel. The solution strainer protects the solenoid valve from debris. If there is little or no 1. Scribe alignment mark on motor barrel to motor solution flow to the ground, check the strainer for cap.
MAINTENANCE 8. TRACTION MOTOR 9. CIRCUIT BREAKERS Circuit breakers interrupt the flow of power in WARNING the event of an electrical overload. When a Do not use a pressure washer to clean around the circuit breaker is tripped, reset it by pressing motors.
4. Remove vacuum motor mounting bracket bolts, which are located under frame. 5. Remove vacuum motor and mounting bracket assembly. 6. Reverse steps to install Note: Place Vacuum Motor Carbon Brushes Replacement (Windsor) stop in End Cap groove. Carbon Brushes Important: These brushes wear quicker as the length shortens due to increased heat.
MAINTENANCE 12. ACTUATOR SCRUB DECK SCRUB DECK ACTUATOR ADJUSTMENT REMOVAL/REPLACEMENT The actuator will need to be adjusted when replaced. FOR SAFETY: Before leaving or servicing To adjust the actuator: machine, stop on a level surface, turn off machine and set parking brake (If option is 1.
Page 31
MAINTENANCE RECOMMENDED GREASING: 1-2 strokes of Mobiltemp®78 or compatible clay-based or calcium-based grease. CUTTER 24V 86039080 04/17/07 4-13...
MACHINE TROUBLESHOOTING PROBLEM CAUSE SOLUTION Poor or no water pick-up Squeegee out of adjustment Adjust squeegee Debris caught on squeegee Remove debris Worn squeegee blades Rotate or replace squeegee blades Vacuum hose clogged Clear obstruction from hose Vacuum hose disconnected Reconnect vacuum hose from squeegee or recovery tank...
Page 33
MACHINE TROUBLESHOOTING PROBLEM CAUSE SOLUTION Little or no solution flow to the floor Solution tank empty Fill solution tank Solution flow turned off or Turn on or increase flow set too low setting Solution strainer plugged Clean solution strainer Solution hoses obstructed Clear obstruction from hose Solution solenoid valve Clean or replace...
COVER (FRONT) & TANK MOUNT CUTTER 24V 86039080 04/17/07...
Page 37
COVER (FRONT) & TANK MOUNT SERIAL NO. PART NO. PRV NO. DESCRIPTION FROM NOTES: 86070150 140574 BRKT, TANK MOUNT 24V 86010670 87029 WASHER, 5/16 FLAT SS 86276780 70728 SCR, 5/16-18 X 3/4 HHCS SS 86062530 27925 COVER, FRONT, 24V GRY 86004790 48012 KNOB, 5/16 –18 4 PRONG...
COVER (TOP) & TANK MOUNT CUTTER 24V 86039080 04/17/07...
Page 39
COVER (TOP) & TANK MOUNT SERIAL NO. PART NO. PRV NO. DESCRIPTION FROM NOTES: 86062540 27926 COVER, TOP 24V GRY 86271840 57285 NUT, 5/16-18 HEX NYLOCK THIN SS 86010670 87029 10 WASHER, 5/16 FLAT SS 86239630 41429 HINGE, COVER TO TANK 86276780 70728 SCR, 5/16-18 X 3/4 HHCS SS...
Page 53
SCRUB DECK AQUA-MIZER-26IN SCRUBHEAD SERIAL NO. PART NO. PRV NO. DESCRIPTION FROM NOTES: 86006930 70514 SCR, 5/16-18 X 1.00 BSHCS SS 86228840 09124 BEARING, FLANGED .314 ID X .502 OD 86259420 87232 WASHER, THRUST .51 ID X 1 OD BRO 86259400 87205 WASHER, THRUST .51 ID X 1 OD BRO...
Page 55
SCRUB DECK AQUA-MIZER-32IN SCRUBHEAD SERIAL NO. PART NO. PRV. NO DESCRIPTION FROM NOTES: 86006930 70514 SCR, 5/16-18 X 1.00 BSHCS SS 86228840 09124 BEARING, FLANGED .314 ID X .502 OD 86259420 87232 WASHER, THRUST .51 ID X 1 OD BRO 86259400 87205 WASHER, THRUST .51 ID X 1 OD BRO...
Page 63
SCRUB DECK LIFT LINKAGE-26IN SCRUBDECK SERIAL NO. PART NO. PRV. NO DESCRIPTION FROM NOTES: 86273780 70015 SCR, 1/4-20 X 3/4 HHCS SS NP 86066760 140545 BRACKET, ANGLE SUPPORT LEFT 86273740 70010 SCR, 1/4-20 X 1.5 HHCS SS 86010630 87013 WASHER, 1/4ID X 5/8OD SS 86271870 57290 NUT, 1/4-20 HEX NYLOCK THIN SS...
Page 69
SCRUB DECK LIFT SERIAL NO. PART NO. PRV NO. DESCRIPTION FROM NOTES: 86276920 70755 SCR, 3/8-16 X 1HHCS SS NP 86279590 87185 WASHER, 3/8 SEALING X 3/4 OD WAS 87003 86069590 140479 BRACKET, ACTUATOR MOUNT BACK 86069600 140480 BRACKET, ACTUATOR MOUNT FRONT 86272410 66233 PIN, CLEVIS 3/8”...
Page 85
WIRING-BATTERY SERIAL NO. PART NO. PRV NO. DESCRIPTION FROM NOTES: 86010120 82803 CONNECTOR, RED 24V 86271870 57290 NUT, 1/4-20 HEX NYLOCK THIN SS 86271910 57295 NUT, 5/16-18 FLEXLOCK 86008920 80889 BOOT, RUBBER TERM. ISOLATOR 86009000 81131 WIRE, 4 X 9.5 BK 5/16 RING X 5/16 RING 86010850 880352 WIRE, 4X20 RD C, TERM X 5/16 RING...
WIRING-CONTROL PANEL DIAGRAM B DIAGRAM A 51 RED 30 RED 49 BLK 56 RED 18 BLU 48 BLK 47 RED 52 RED 41 BLU 29 YLW 50 BLK 43 BLK 63 BLK 62 RED 63 BLK 26 RED 61 BLK 33 RED 2/25 BLK 28 WHT...
Page 87
WIRING-CONTROL PANEL SERIAL NO. PART NO. PRV NO. DESCRIPTION FROM NOTES: 86238990 41442 HARNESS, PANEL, DELUXE 86261210 29204 DIODE ASM, 76008 X 76008 86003410 29215 DIODE ASM, 76075 X 76075 86267340 880269 WIRE, 22” RED/18 76040 X 76075 86269300 88868 WIRE, 16”...
WIRING-MAIN HARNESS 74 RED RIGHT BRUSH MOTOR 75 BLK 76 RED LEFT BRUSH MOTOR 77 BLK 72 RED MOTOR 73 BLK 5 BRN DIAGRAM A 6 BLK ACTUATOR 75 BLK 78 RED 79 BLK 76 RED 69 RED 77 BLK 74 RED 68 GRN/YLW SOLENOID...
Page 89
WIRING-MAIN HARNESS SERIAL NO. PART NO. PRV NO. DESCRIPTION FROM NOTES: 86238980 41441 HARNESS, MAIN CUTTER 24V 86039080 04/17/07 5-56...
Page 93
BRAKE-OPTION SERIAL NO. PART NO. PRV NO. DESCRIPTION FROM NOTES: 86248370 66381 PAD, BRAKE 86006220 66192 PIN, ROLL 1/4 X 1.25L 86252070 67486 ROD, BRAKE 24V 86231330 14664 BUSH, BRZ FLG .63 X .75 X 1.0 86255060 73426 SPRING, EXT .43D X 2.50 L X .047 W 86070070 140565 BRKT, LOWER BRAKE MOUNT 24V...