Page 1
Operating Instructions (ENG) Bedienungsanleitung (GER) Istruzioni operative (ITA) Instrucciones de funcionamiento (SPA) MODELS: SCE264 10052270 IPX4 Read these instructions before using the machine Bitte lesen Sie diese Anleitungen, bevor Sie die Maschine in Gebrauch nehmen Leggere attentamente queste istruzioni prima di azionare la macchina Lea las instrucciones antes de utilizar la máquina...
Warranty Registration Thank you for purchasing a Windsor product. Warranty registration is quick and easy. Your registration will allow us to serve you better over the lifetime of the product.
TABLE OF CONTENTS Machine Data Log/Overview......2 Brush Shrouds & Brush Skirts ....4-10 Table of Contents..........3 Vacuum Motor ...........4-11 Greasing Instructions.........4-12 HOW TO USE THIS MANUAL Machine Troubleshooting ......4-13 GROUP PARTS LIST How to use this Manual.........1-1 SAFETY Control Handle..........
They are Parts may be ordered from authorized Windsor listed in this general order: dealers. When placing an order for parts, the machine model and machine serial number are Batteries important.
IMPORTANT SAFETY INSTRUCTIONS When using an battery powered appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. To reduce the risk of fire, electric shock, or injury: WARNING: se only indoors. Do not use outdoors or expose to rain. Use only as described in this manual.
WHEN SERVICING MACHINE: Avoid moving parts. Do not wear loose clothing; jackets, shirts, or sleeves when working on the machine. Use Windsor approved replacement parts. WARNING Batteries emit hydrogen gas. Explosion or fire can result. Keep sparks and open flame away. Keep top cover in raised position when charging.
SAFETY LABEL LOCATION NOTE: These drawings indicate the location of safety labels on the machine. If at any time the labels become illegible, promptly replace them. SAFETY DECAL 86252530 PRV NO. 81494 BATTERY CAUTION 86252520 PRV NO. 80885 CIRCUIT BREAKER DECAL 86243530 SEE MANUAL PRV NO.
TECHNICAL SPECIFICATIONS ITEM DIMENSION/CAPACITY Nominal power 1450 W Rated Voltage 24VDC Rated Amperage 60 Amps Batteries 4 X 6 Volt 250-305-335 AH @ 20 hr rate Scrub Brush Motors 2 X .75 hp (0.56 kW) Vacuum Motor .75 hp (0.56 Kw) Propelling Motor .3 hp (0.22 Kw) Mass (GVW)
Page 9
TECHNICAL SPECIFICATIONS ITEM MEASURE Height 45 in. (114 cm) Length with 26 in. (66 cm) scrub head 64 in. (163 cm) Width without squeegee and scrub head 24 in. (61 cm) Width of squeegee for 26 in. (66 cm) scrub head 35 in.
HOW THE MACHINE WORKS The Saber Cutter is a battery powered, self- The function of the recovery system is to vacuum propelled, hard floor scrubber intended for the soiled water back into the recovery tank. The commercial use. The appliance applies a recovery system consists of the squeegee, cleaning solution onto a hard floor, scrubs the vacuum motor, float ball filter, recovery tank and...
COMPONENTS 1. Control Panel 2. Front Cover 3. Recovery Tank 4. Recovery Tank Drain Hose 5. Scrub Head Shrouds 6. Solution Tank 7. Solution Tank Cover 8. Solution Tank Drain Hose 9. Solution Strainer 10. Squeegee 11. Aqua-Mizer 12. Top Cover 13.
Page 13
CONTROLS 1. Key Switch 9. Vacuum Switch 2. Emergency Shut Off Switch 10. Squeegee Lift Lever 3. Speed Control Knob 11. Squeegee Pitch Adjustment Knob 4. Propel Control Lever 12. Squeegee Deflection Adjustment Knobs 5. Reverse Button 13. Battery Charge Level Indicator 6.
Page 14
CONTROLS 7. BRUSH PRESSURE LEVER 11. SQUEEGEE PITCH ADJUSTMENT Adjusts the amount of brush pressure to the floor by KNOB raising or lowering the scrub deck. Adjusts the deflection at the ends of the To apply brush pressure, lower brush pressure lever to squeegee.
Page 15
CONTROLS 13. BATTERY CHARGE LEVEL INDICATOR Indicates the charge level of the batteries. The meter display is divided into 10 vertical bars. Bar illuminated on the far right indicate full charge. Bars flashing near the left side indicate the batteries should be recharged. Further operation of the machine could damage the machine or the batteries.
MACHINE OPERATION FILLING SOLUTION TANK PRE-RUN MACHINE INSPECTION FOR SAFETY: Before leaving or servicing Do a pre-run inspection to find possible problems that machine; stop on level surface, turn off machine could cause poor performance or lost time from and remove key. breakdown.
MACHINE OPERATION TO BEGIN SCRUBBING NORMAL SCRUBBING Plan the scrubbing pattern in advance. The WARNING longest track is around the perimeter of the area When operating the machine around people, pay to be cleaned. For efficient operation, the runs close attention for unexpected movement. Use should be the longest possible without turning, extra caution around children.
MACHINE OPERATION DOUBLE SCRUB RECOVERY TANK For floors which are heavily soiled or have thick 1. Unhook the large drain hose from the retainer. accumulations of floor finish may not clean Unscrew the T-handle on plug enough to loosen sufficiently with one pass. In these cases it will be plug, then lower hose in direction of the drain.
MAINTENANCE SERVICE SCHEDULE MAINTENANCE DAILY WEEKLY MONTHLY Check batteries after charging; add water if necessary Check pad wear to prevent buildup of chemicals Check linkages and connectors for wear and damage Check hoses for wear, blockages, or damage Clean squeegee; check for adjustment; inspect for wear Check handles, switches, knobs, domes, and gaskets for damage...
Page 20
MAINTENANCE 1. Batteries 2. Squeegee 3. Aqua Mizer 4. Scrub Brushes 5. Recovery Tank Float Shut-Off 6. Solution Strainer 7. Brush Motor 8. Traction Motor Circuit Breakers Brush Shroud & Brush Skirts Vacuum Motor CUTTER 24V (SCE) 86037010 02/21/07...
MAINTENANCE 1. BATTERIES The batteries provide the power to operate the CAUTION machine. The batteries require regular maintenance When servicing machine, avoid contact with to keep them operating at peak efficiency. battery acid. The machine batteries will hold their charge for long WARNING periods of time, but they can only be charged a Batteries emit hydrogen gas.
MAINTENANCE TO CHARGE THE BATTERIES CHECKING BATTERY SPECIFIC GRAVITY WARNING Use a hydrometer to check the battery specific gravity. When servicing machine, avoid contact with battery acid. CAUTION Batteries emit hydrogen gas. Explosion or fire Battery Check can result. Keep sparks and open flame away. Keep covers open when charging.
MAINTENANCE 5. Replace the battery caps, and leave them in CHANGING BATTERIES place while charging. Stop the machine in a clean area next to the 6. Unplug the battery connector from the machine. charger. Turn off machine. FOR SAFETY: When charging, connect the FOR SAFETY: Before leaving or servicing the charger to the batteries before connecting the machine;...
MAINTENANCE 2. SQUEEGEE BLADES TO REMOVE SQUEEGEE ASSEMBLY The front squeegee blade allows solution to pass 1. With the squeegee in the up position, turn key through channels in the blade into the squeegee switch “OFF”. assembly while maintaining vacuum to provide lift. 2.
MAINTENANCE TO ADJUST SQUEEGEE PITCH TO ADJUST AMOUNT OF REAR SQUEEGEE DEFLECTION 1. Choose a smooth, level surface. Turn “ON” the key switch. Lower the squeegee and drive 1. Choose a smooth, level surface. Lower the forward at least 2 feet (60cm.). squeegee and drive forward at least 2 feet 2.
MAINTENANCE SCRUB BRUSHES REPLACING OR INSTALLING SCRUB BRUSHES There are four different types of brushes available to cover applications from cleaning heavily soiled floors 1. With the scrub deck up, turn “OFF” the machine. to polishing. A pad driver is also available to take advantage of the many cleaning pads on the market.
MAINTENANCE 6. SOLUTION STRAINER BRUSH MOTOR CARBON BRUSH REPLACEMENT The solution strainer is located in front of the left front wheel. The solution strainer protects the 1. Scribe alignment mark on motor barrel to motor solenoid valve from debris. If there is little or no cap.
MAINTENANCE 8. TRACTION MOTOR 9. CIRCUIT BREAKERS Circuit breakers interrupt the flow of power in WARNING the event of an electrical overload. When a Do not use a pressure washer to clean around the circuit breaker is tripped, reset it by pressing motors.
4. Loosen clamp and disconnect hose from vacuum intake. 5. Remove vacuum motor mounting bracket bolts. 6. Remove vacuum motor from mounting bracket. 7. Reverse steps to install. Note: Place Vacuum Motor Carbon Brushes Replacement (Windsor) stop in End Cap groove. Carbon Brushes Important: These brushes wear quicker as the length shortens due to increased heat.
Page 30
MAINTENANCE RECOMMENDED GREASING: 1-2 strokes of Mobiltemp®78 or compatible clay-based or calcium-based grease. 4-12 CUTTER 24V (SCE) 86037010 02/21/07...
MACHINE TROUBLESHOOTING PROBLEM CAUSE SOLUTION Poor or no water pick-up Squeegee out of adjustment Adjust squeegee Debris caught on squeegee Remove debris Worn squeegee blades Rotate or replace squeegee blades Vacuum hose clogged Clear obstruction from hose Vacuum hose disconnected Reconnect vacuum hose from squeegee or recovery tank...
Page 32
MACHINE TROUBLESHOOTING PROBLEM CAUSE SOLUTION Little or no solution flow to the floor Solution tank empty Fill solution tank Solution flow turned off or set Turn on or increase flow too low setting Solution strainer plugged Clean solution strainer Solution hoses obstructed Clear obstruction from hose Solution solenoid valve Clean or replace...
Page 33
THIS PAGE LEFT BLANK INTENTIONALLY 4-15 CUTTER 24V (SCE) 86037010 02/21/07...
COVER (FRONT) & TANK MOUNT CUTTER 24V (SCE) 86037010 02/21/07...
Page 37
COVER (FRONT) & TANK MOUNT SERIAL NO. PART NO. PRV NO. DESCRIPTION FROM NOTES: 86070150 140574 BRKT, TANK MOUNT 24V 86010670 87029 WASHER, 5/16 FLAT SS 86276780 70728 SCR, 5/16-18 X 3/4 HHCS SS 86062530 27925 COVER, FRONT, 24V GRY 86004790 48012 KNOB, 5/16 –18 4 PRONG...
COVER (TOP) & TANK MOUNT CUTTER 24V (SCE) 86037010 04/12/07...
Page 39
COVER (TOP) & TANK MOUNT SERIAL NO. PART NO. PRV NO. QTY DESCRIPTION FROM NOTES: 86062540 27926 COVER, TOP 24V GRY 86271840 57285 NUT, 5/16-18 HEX NYLOCK THIN SS 86010670 87029 10 WASHER, 5/16 FLAT SS 86239630 41429 HINGE, COVER TO TANK 86276780 70728 SCR, 5/16-18 X 3/4 HHCS SS...
Page 53
SCRUB DECK AQUA-MIZER-26IN SCRUBHEAD SERIAL NO. PART NO. PRV NO. DESCRIPTION FROM NOTES: 86006930 70514 SCR, 5/16-18 X 1.00 BSHCS SS 86228840 09124 BEARING, FLANGED .314 ID X .502 OD 86259420 87232 WASHER, THRUST .51 ID X 1 OD BRO 86259400 87205 WASHER, THRUST .51 ID X 1 OD BRO...
Page 59
SCRUB DECK LIFT LINKAGE-26IN SCRUBDECK SERIAL NO. PART NO. PRV NO. DESCRIPTION FROM NOTES: 86273780 70015 SCR, 1/4-20 X 3/4 HHCS SS NP 86069910 140545 BRACKET, ANGLE SUPPORT LEFT 86273740 70010 SCR, 1/4-20 X 1.5 HHCS SS 86010630 87013 WASHER, 1/4ID X 5/8OD SS 86271870 57290 NUT, 1/4-20 HEX NYLOCK THIN SS...
Page 61
SCRUB DECK LIFT LINKAGE-CENTER SERIAL NO. PART NO. PRV NO. DESCRIPTION FROM NOTES: 86273820 70019 SCR, 1/4-20 X 1.25 HHCS SS 86010630 87013 WASHER, 1/4 ID X 5/8 OD SS 86228900 09138 BEARING FLANGED, .252 ID X .503 OD 86259400 87205 WASHER, THRUST .51 ID X 1 OD BRO 86259410...
Page 63
SCRUB DECK LIFT LINKAGE-FRONT & REAR SERIAL NO. PART NO. PRV NO. DESCRIPTION FROM NOTES: 86066990 51366 BAR, VERTICAL LINK 86067000 51375 BAR, VERTICAL BRACE 86273810 70018 SCR, 1/4-20 X 1 HHCS SS 86228900 09138 BEARING, FLANGED .252ID X .503OD 86010630 87013 WASHER, 1/4ID X 5/8OD SS...
Page 77
WIRING-BATTERY SERIAL NO. PART NO. PRV NO. QTY DESCRIPTION FROM NOTES: 86010120 82803 CONNECTOR, 175 DCA RED W/O TERMS 86271870 57290 CABLE ASM, BAT. JUMPER X 15” 86002510 23125 WIRE 4X 15 B CLAMP X B CLAMP NOT SHOWN 86002570 23190 WIRE, 4 X 27 RD B CLAMP X C TERM NOT SHOWN...
WIRING-CONTROL PANEL DIAGRAM B DIAGRAM A 51 RED 30 RED 49 BLK 56 RED 48 BLK 47 RED 52 RED 29 YLW 50 BLK 43 BLK 62 BLK 63 RED 63 BLK 26 RED 66 BLK 61 BLK 65 RED 2 BLK 28 WHT 86269300...
Page 79
WIRING-CONTROL PANEL SERIAL NO. PART NO. PRV NO. DESCRIPTION FROM NOTES: 86239000 41443 HARNESS, PANEL BASIC 86261210 29204 DIODE ASM, 76008 X 76008 86003410 29215 DIODE ASM, 76075 X 76075 86267340 880269 WIRE, 22” RED/18 76040 X 76075 86269300 88868 WIRE, 16”...
Page 80
WIRING GROUP – MAIN HARNESS 74 RED RIGHT BRUSH MOTOR 75 BLK 76 RED LEFT BRUSH MOTOR 77 BLK 72 RED MOTOR 73 BLK DIAGRAM A 73 BLK 75 BLK 78 RED 79 BLK 76 RED 69 RED 72 RED 77 BLK 74 RED 68 GRN/YLW...
Page 81
WIRING GROUP – MAIN HARNESS SERIAL NO. PART NO. PRV NO. DESCRIPTION FROM NOTES: 86238980 41441 HARNESS, MAIN CUTTER 24V (SCE) 86037010 02/21/07 5-48...
Page 85
BRAKE SERIAL NO. PART NO. PRV NO. DESCRIPTION NOTES: FROM 86248370 66381 PAD, BRAKE 86006220 66192 PIN, ROLL 1/4 X 1.25L 86252070 67486 ROD, BRAKE 24V 86231330 14664 BUSH, BRZ FLG .63 X .75 X 1.0 86255060 73426 SPRING, EXT .43D X 2.50 L X .047 W 86070070 140565 BRKT, LOWER BRAKE MOUNT 24V...